烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

人工闪锌矿氧压酸浸过程中Cu2+的催化机理研究

The potential autoclave was used to study the catalytic mechanism of Cu2+ during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu2+ formed a CuS deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu2+. At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

超声振动辅助钨极惰性气体焊接异种金属 316L 和 L415

Ultrasonic vibration assisted tungsten inert gas welding was applied to joining stainless steel 316L and low alloy high strength steel L415. The effect of ultrasonic vibration on the microstructure and mechanical properties of a dissimilar metal welded joint of 316L and L415 was systematically investigated. The microstructures of both heat affected zones of L415 and weld metal were substantially refined, and the clusters of δ ferrite in traditional tungsten inert gas (TIG) weld were changed to a dispersive distribution via the ultrasonic vibration. The ultrasonic vibration promoted the uniform distribution of elements and decreased the micro-segregation tendency in the weld. With the application of ultrasonic vibration, the average tensile strength and elongation of the joint was improved from 613 to 650 MPa and from 16.15% to 31.54%, respectively. The content of Σ3 grain boundaries around the fusion line zone is higher and the distribution is more uniform in the ultrasonic vibration assisted welded joint compared with the traditional one, indicating an excellent weld metal crack resistance.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

荔枝龙眼炭疽病和霜疫霉病的识别与防治

总结了荔枝龙眼重要病害炭疽病和霜疫霉病的症状、病原、发生规律及综合防治措施;指出荔枝龙眼炭疽病和霜疫霉病主要为害叶片、花穗和果实,叶片早落,花穗干枯死亡,果实腐烂并产生异味;两种病害为害造成的损失很大,防治必须及时,且防治措施以农业防治和化学防治为主。     

中胚花筒螅辐射幼体附着和变态及其温盐效应

研究了中胚花筒螅辐射幼体的附着和变态过程以及不同温、盐度对辐射幼体附着和变态的影响．结果表明幼体的附着分为暂时性附着及永久性附着两个阶段；幼体附着变态的适宜盐度范围为23～41；适宜温度范围为13～21℃；在较低温度下（9～17℃），幼体可逆性ATT附着时间延长，有利于幼体对附着基底的选择及幼体的扩散．     

中胚花筒螅辐射幼体附着和变态及其温盐效应

研究了中胚花筒螅辐射幼体的附着和变态过程以及不同温、盐度对辐射幼体附着和变态的影响.结果表明幼体的附着分为暂时性附着及永久性附着两个阶段;幼体附着变态的适宜盐度范围为23～41;适宜温度范围为13～21℃;在较低温度下(9～17℃),幼体可逆性ATT附着时间延长,有利于幼体对附着基底的选择及幼体的扩散.     

科技出版与科技学术道德

本文从科技出版的角度探究和思考了当前关注的学术腐败问题，对学术腐败产生的原因、学术腐败在科技出版中的表现以及科技出版如何抵制学术腐败进行了分析，提出了解决问题的意见。     

镁合金板带生产应用现状与发展前景

通过对目前镁合金板带的生产技术、工艺设备和产品应用现状等方面的描述,分析了其生产与应用的特点.同时,通过介绍镁合金板带生产工艺的开发现状,探讨了其发展趋势与前景,尤其是以热轧开坯进行卷式法生产的可能.     

桩土摩擦粘着特性及分析方法

同一土层的桩侧摩阻力在不同条件下取值会有很大区别,因此有必要对桩侧摩阻力的影响因素进行分析。分析了桩土的摩擦粘着机理,指出影响侧摩阻力的因素主要为桩土界面强度及土层强度,其中桩土界面强度包括界面摩擦力和界面粘着力两部分。根据机理分析提出使用有限元法配合试验结果进行分析应包括两方面的(1)根据试验实测结果通过试算确定侧摩阻力极值由桩土界面强度决定还是由土层强度决定;(2)若侧摩阻力由界面强度决定则根据土层特性进行摩擦系数假定,进而确定界面摩擦力及粘着力。介绍了ADINA建模及计算过程。通过应用一组混凝土短桩的静载试验结果进行计算分析来说明分析过程。     

公民的法律理解-解释与和谐社会的治理及建设

基于对公民法律理解-解释问题的分析引出了对公民的法律理解-解释活动与和谐社会善治的内在关系的探讨。和谐社会的善治模式内在地蕴含了公民法律理解-解释的要素,这是构建和谐社会重要的心理基础。公民法律理解-解释活动过程对于和谐社会的建设所具有社会整合作用,正确引导与教育以及优化公民法律理解-解释活动是公民意识教育的重要内容。     

海洋科技发展演变的影响因素及规律探析

海洋科技在漫长的发展演变过程中,由于多种因素的交织作用而形成了特有的发展规律。基于分析影响海洋科技发展的诸如政治、经济、军事等各种因素,探讨海洋科技发展演变规律,有利于深层次理解海洋科技的发展历程、正确把握其发展脉络,并对未来的走势作出科学预测。     

科技腾飞与文学发展

科技腾飞与文学发展是全球语境中的一个重要话题。针对这一话题主要有两种观点:持悲观论调者认为科技腾飞导致文学终结;持乐观论调者认为科技腾飞带来文学进步。究竟谁是谁非是理论界亟待解决的关系到文学及其研究是存在还是消亡的根本性问题。本文认为科技腾飞既没有导致文学的终结也没能带来文学的进步,而是推动了文学的全面发展。这种发展表现为:一,现代科技媒介与制作方式为文学发展拓宽了空间,生产了新的文学种类,为文学大家庭增添了新成员;同时也改变了文学的活动方式。二,新的文学种类的出现、文学活动方式的改变以及高科技时代的后现代语境,使文学的价值功能发生变化,从而赋予文学以鲜明的时代特征———大众的、消费的品格。     

资源开发利用与环境保护

文章论述资源的开发利用和对生态环境保护的关系入手，提出了资源开发利用过程中的自然环境污染及经济评价问题。