烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

人工闪锌矿氧压酸浸过程中Cu2+的催化机理研究

The potential autoclave was used to study the catalytic mechanism of Cu2+ during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu2+ formed a CuS deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu2+. At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

超声振动辅助钨极惰性气体焊接异种金属 316L 和 L415

Ultrasonic vibration assisted tungsten inert gas welding was applied to joining stainless steel 316L and low alloy high strength steel L415. The effect of ultrasonic vibration on the microstructure and mechanical properties of a dissimilar metal welded joint of 316L and L415 was systematically investigated. The microstructures of both heat affected zones of L415 and weld metal were substantially refined, and the clusters of δ ferrite in traditional tungsten inert gas (TIG) weld were changed to a dispersive distribution via the ultrasonic vibration. The ultrasonic vibration promoted the uniform distribution of elements and decreased the micro-segregation tendency in the weld. With the application of ultrasonic vibration, the average tensile strength and elongation of the joint was improved from 613 to 650 MPa and from 16.15% to 31.54%, respectively. The content of Σ3 grain boundaries around the fusion line zone is higher and the distribution is more uniform in the ultrasonic vibration assisted welded joint compared with the traditional one, indicating an excellent weld metal crack resistance.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

《梁山伯与祝英台》与《罗密欧与朱丽叶》调式比较

《梁山伯与祝英台》与《罗密欧与朱丽叶》两部作品的内容都取材于民间故事,都属于标题性音乐作品,作品曲式结构基本相同。不同之处是对造成悲剧原因的展示有着明显区别,主、副部主题的表现和运用截然相反,音乐的主基调有较大差异,作品的整体风格迥异。     

有氧运动与身心健康探析

健康与运动是密不可分的,运动分为有氧和无氧,有氧运动较无氧运动更易普及和被大众接受,从人体长期参加有氧运动对人的身体健康和心理健康的角度来阐述有氧运动对人体的良好影响。     

高校管理与师生权益的保护

当前,因高校管理引发的法律纠纷呈上升趋势,究其原因是师生的法治观念在增强,另一方面说明高校在师生管理等方面也存在诸多不适应。要改变这些不适应,就要进行依法治校,更新管理理念。做到规章制度合法、管理行为合法。努力加强法制教育工作和师德校风建设,切实保障师生的合法权益。     

博客与高校思想政治教育

网络的发展为我们带来全新便捷的互动平台和交流方式,博客是当今传播文化的重要载体,因个体性、公共性、开放性、成本投入少等特点吸引着"90后"大学生广泛关注。在新形势的要求下,高校辅导员应主动占领网络博客思想政治教育新阵地,加强辅导员博客建设,根据大学生的心理特点,利用博客提升网络思想政治教育工作的吸引力和感染力,创新高校思想政治教育。     

道教与魏晋南北朝文人的功利欲望

欲望是作家创作的内驱力,道教对中国古代文人的欲望有什么影响,这是研究中国古代文学和文学理论不能不思考的问题。本文从道教的功利性,文人纷纷走近道教,文学观念中的道教因素等方面,对道教与魏晋南北朝文人的功利欲望作些专门探讨。这无疑会拓展人们研究的新视界。     

文献信息情报工作在科技工作及立项决策中的作用

本文揭示了在当今信息市场形势下 ,文献信息情报工作在科技工作和经济立项决策中的作用 ,同时也指出 :图书馆文献信息工作者们能在强手如云的信息市场中占领一块阵地也应成为图书馆界的共识     

我国的沙暴、尘暴及其防治

 我国是沙尘暴易发的国家, 进入90年代以来, 沙尘暴有频率增加、强度加大、范围扩展、危害程度加剧的趋势。据统计, 我国发生强沙尘暴的次数, 50年代为5次, 60年代为8次, 70年代为13次, 80年代为14次[1], 90年代为23次[2], 呈明显上升趋势。沙尘暴的强度及造成的损失, 以90年代最为突出, 发生于1993年5月5日(5.5沙尘暴)和1998年4月16日(4.16沙尘暴)的特大强沙尘暴, 是我国近100年来所罕见, 损失极其惨重。     

我国的沙暴、尘暴及其防治

我国是沙尘暴易发的国家 ,进入９０年代以来 ,沙尘暴有频率增加、强度加大、范围扩展、危害程度加剧的趋势。据统计 ,我国发生强沙尘暴的次数 ,５０年代为５次 ,６０年代为８次 ,７０年代为１３次 ,８０年代为１４次［１］ ,９０年代为２３次［２］ ,呈明显上升趋势。沙尘暴的强度及造成的损失 ,以９０年代最为突出 ,发生于１９９３年５月５日（５．５沙尘暴）和１９９８年４月１６日（４．１６沙尘暴）的特大强沙尘暴 ,是我国近１００年来所罕见 ,损失极其惨重。５、５沙尘暴锋面前移速度１４～１７米／秒 ,最大１９．５米／秒 ,瞬时最大风…     

辽金诗文话语与佛禅

辽金诗文作品中存在着大量的由佛经禅典移植而来的话语。这一现象从特定侧面体现了佛禅对中国古代文学的渗透溶浸。其表现主要反映在借用佛禅意像、使用佛禅故实和引用佛禅语汇三方面。