氧化锌矿物浸出渣中铅、锶的提取及动力学分析

NH₄HCO₃ conversion followed by HCl leaching was performed and proven to be effective in extracting Pb and Sr from zinc extracted residual. The mechanism and operating conditions of NH₄HCO₃ conversion, including molar ratio of NH₄HCO₃ to zinc extracted residual, NH₄HCO₃ concentration, conversion temperature, conversion time, and stirring velocity, were discussed, and operating conditions were optimized by the orthogonal test. Experimental results indicate that NH₄HCO₃ conversion at temperatures ranging from 25 to 85°C follows the shrinking unreacted core model and is controlled by inner diffusion through the product layer. The extraction ratios of Pb and Sr under optimized conditions reached 85.15% and 87.08%, respectively. Moreover, the apparent activation energies of Pb and Sr were 13.85 and 13.67 kJ·mol?1, respectively.     

皮秒Nd:YAG激光对生物金属纯Ti和Ti–13Nb–13Zr合金的表面改性

The effects of picosecond Nd:YAG laser irradiation on chemical and morphological surface characteristics of the commercially pure titanium and Ti–13Nb–13Zr alloy in air and argon atmospheres were studied under different laser output energy values. During the interaction of laser irradiation with the investigated materials, a part of the energy was absorbed on the target surface, influencing surface modifications. Laser beam interaction with the target surface resulted in various morphological alterations, resulting in crater formation and the presence of microcracks and hydrodynamic structures. Moreover, different chemical changes were induced on the target materials’ surfaces, resulting in the titanium oxide formation in the irradiation-affected area and consequently increasing the irradiation energy absorption. Given the high energy absorption at the site of interaction, the dimensions of the surface damaged area increased. Consequently, surface roughness increased. The appearance of surface oxides also led to the increased material hardness in the surface-modified area. Observed chemical and morphological changes were pronounced after laser irradiation of the Ti–13Nb–13Zr alloy surface.     

基于响应曲面法的铁焦冶金性能多目标协同优化

Iron carbon agglomerates (ICA) are used to realize low-carbon blast furnace ironmaking. In this study, the central composite design based on response surface methodology was used to synergistically optimize the compressive strength, reactivity, and post-reaction strength of ICA. Results show that the iron ore addition ratio significantly influences the compressive strength, reactivity, and post-reaction strength of ICA. The iron ore addition ratio and carbonization temperature or the iron ore addition ratio and carbonization time exert significant interaction effects on the compressive strength and reactivity of ICA, but it has no interaction effects on the post-reaction strength of ICA. In addition, the optimal process parameters are as follows: iron ore addition ratio of 15.30wt%, carbonization temperature of 1000°C, and carbonization time of 4.27 h. The model prediction results of compressive strength, reactivity, and post-reaction strength are 4026 N, 55.03%, and 38.24%, respectively, which are close to the experimental results and further verify the accuracy and reliability of the models.     

汽车用废弃锂离子电池的减量化、再生及回收研究进展

The demand for Li-ion batteries (LIBs) for vehicles is increasing. However, LIBs use valuable rare metals, such as Co and Li, as well as environmentally toxic reagents. LIBs are also necessary to utilize for a long period and to recycle useful materials. The reduction, reuse, and recycle (3R) of spent LIBs is an important consideration in constructing a circular economy. In this paper, a flowsheet of the 3R of LIBs is proposed and methods to reduce the utilization of valuable rare metals and the amount of spent LIBs by remanufacturing used parts and designing new batteries considering the concept of 3R are described. Next, several technological processes for the reuse and recycling of LIBs are introduced. These technologies include discharge, sorting, crushing, binder removal, physical separation, and pyrometallurgical and hydrometallurgical processing. Each process, as well as the related physical, chemical, and biological treatments, are discussed. Finally, the problem of developed technologies and future subjects for 3R of LIBs are described.     

传统加热和微波加热下氧化锰矿的碳热还原行为研究

For the purpose of exploring a potential process to produce FeMn, the effects of microwave heating on the carbothermal reduction characteristics of oxidized Mn ore was investigated. The microwave heating curve of the mixture of oxidized Mn ore and coke was analyzed in association with the characterization of dielectric properties. The comparative experiments were conducted on the carbothermal reductions through conventional and microwave heatings at temperatures ranging from 973 to 1373 K. The thermogravimetric analysis showed that carbothermal reactions under microwave heating proceeded to a greater extent and at a faster pace compared with those under conventional heating. The metal phases were observed in the microstructures only under microwave heating. The carbothermal reduction process under microwave heating was discussed. The electric and magnetic susceptibility differences were introduced into the thermodynamics analysis for the formation of metal Mn. The developed thermodynamics considered that microwave heating could make the reduction of MnO to Mn more accessible and increase the reduction extent.     

机械合金化法制备的Cu/SiC纳米复合材料的组织、热性能和力学性能评估

Nano-sized silicon carbide (SiC: 0wt%, 1wt%, 2wt%, 4wt%, and 8wt%) reinforced copper (Cu) matrix nanocomposites were manufactured, pressed, and sintered at 775 and 875°C in an argon atmosphere. X-ray diffraction (XRD) and scanning electron microscopy were performed to characterize the microstructural evolution. The density, thermal expansion, mechanical, and electrical properties were studied. XRD analyses showed that with increasing SiC content, the microstrain and dislocation density increased, while the crystal size decreased. The coefficient of thermal expansion (CTE) of the nanocomposites was less than that of the Cu matrix. The improvement in the CTE with increasing sintering temperature may be because of densification of the microstructure. Moreover, the mechanical properties of these nanocomposites showed noticeable enhancements with the addition of SiC and sintering temperatures, where the microhardness and apparent strengthening efficiency of nanocomposites containing 8wt% SiC and sintered at 875°C were 958.7 MPa and 1.07 vol%?1, respectively. The electrical conductivity of the sample slightly decreased with additional SiC and increased with sintering temperature. The prepared Cu/SiC nanocomposites possessed good electrical conductivity, high thermal stability, and excellent mechanical properties.     

空冷条件下钛渣颗粒的氧化路径及氧化动力学

The oxidation pathway and kinetics of titania slag powders in air were analyzed using differential scanning calorimetry (DSC) andthermogravimetry (TG). The oxidation pathway of titania slag powder in air was divided into three stages according to their three exothermic peaks and three corresponding mass gain stages indicated by the respective non-isothermal DSC and TG curves. The isothermal oxidation kin-etics of high titania slag powders of different sizes were analyzed using the ln-ln analysis method. The results revealed that the entire isotherm-al oxidation process comprises two stages. The kinetic mechanism of the first stage can be described as f (α)=1.77 (1?α) [?ln (1?α)](1.77?1)/1.77 , f (α)=1.97 (1?α) [?ln (1?α)](1.97?1)/1.97 , and f (α)=1.18 (1?α) [?ln (1?α)](1.18?1)/1.18 . The kinetic mechanism of the second stage for all samples can be described as f (α)=1.5(1?α)2/3[1?(1?α)1/3]?1 . The activation energies of titania slag powders with different sizes (d1 < 0.075 mm, 0.125 mm < d2 < 0.150 mm, and 0.425 mm < d3 < 0.600 mm) for different reaction degrees were calculated. For the given experimental conditions, the rate-controlling step in the first oxidation stage of all the samples is a chemical reaction. The rate-controlling steps of the second oxidation stage are a chemical reaction and internal diffusion (for powders d1 < 0.075 mm) and internal diffusion (for powders 0.125 mm < d2 <0.150 mm and 0.425 mm < d3 < 0.600 mm).     

烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

铁酸锌焙烧后的还原行为及氨浸特性

A novel method for recovering zinc from zinc ferrite by reduction roasting–ammonia leaching was studied in this paper. The reduction thermodynamic of zinc ferrite by CO was analyzed. The effects of roasting parameters on the phase transformation and conversion rate of zinc ferrite, and the leaching behavior of zinc from the reductive roasted samples by ammonia leaching, were experimentally investigated. The mineralogical phase compositions and chemical compositions of the samples were characterized by X-ray diffraction and chemical titration methods, respectively. The results showed that most of the zinc ferrite was transformed to zinc oxide and magnetite after weak reduction roasting. 86.43% of the zinc ferrite was transformed to zinc oxide under the optimum conditions: CO partial pressure of 25%, roasting temperature of 750°C, and roasting duration of 45 min. Finally, under the optimal leaching conditions, 78.12% of zinc was leached into the solution from the roasted zinc ferrite while all iron-bearing materials were kept in the leaching residue. The leaching conditions are listed as follows: leaching duration of 90 min, ammonia solution with 6 mol/L concentration, leaching temperature of 50°C, solid-to-liquid ratio of 40 g/L, and stirring speed of 200 r/min.     

浅析航海过失和管货过失

《海牙规则》确立了海运承运人对航海过失造成的货损免责，航海过失可分为驾船过失和管船过失。但承运人对管货过失造成的货损应承担赔偿责任。区分航海过失，尤其是管船过失与管货过失，成为一项极其重要的任务。近百的来，有关于此的争议不同涌现，国际上要求废除航海过失免责的呼声日益高涨，《汉堡规则》虽废除了航海过失免责，但亦未被国际社会所接受。文章探讨了航海过失与管货过失的区分标准，并尝试建立一种新的承运人责任制度。     

以党内和谐促党群和谐,以党群和谐带社会和谐

党内关系的和谐状态不仅是衡量党的自身建设成效的重要标准,更是提高党的执政能力建设和永葆党的先进性的内在要求。党内和谐是党群和谐的根本,对党群关系和谐与社会和谐起着重要的示范和带动作用。要以党内和谐促进社会和谐,以优良的党风促政风带民风,必须通过党群关系的良性互动来实现。     

以党内和谐促党群和谐,以党群和谐带社会和谐

党内关系的和谐状态不仅是衡量党的自身建设成效的重要标准,更是提高党的执政能力建设和永葆党的先进性的内在要求.党内和谐是党群和谐的根本,对党群关系和谐与社会和谐起着重要的示范和带动作用.要以党内和谐促进社会和谐,以优良的党风促政风带民风,必须通过党群关系的良性互动来实现.     

从银政及银企关系看国家注资改造国有银行的有效性

通过对政府从国有银行退出的艰巨性和国有银行和国有企业之间建立真正债关系的艰巨性的角度,对国家通过注资的方式改造国有商业银行的有效性进行了深入的分析,结果表明:我国国有商业银行的改革决不是简单通过注资就可以一蹴而就的。根据分析的结果提出了对国有商业银行改革的意见和建议。     

智能化电能表及自动抄表系统在住宅中的应用

本文主要论述了智能化电能表及自动抄表系统的组成、特点，以及目前市场上使用的几种主要智能化电能表和自动抄表系统的方式及其发展趋势．     

建设以公众为中心的电子政府

从我国电子政府的发展现状出发,以上海市各级政府的电子政务为例,对我国各级电子政府建设在迅速发展的同时所呈现出的一些问题及面临的障碍进行分析,并提出以满足公众需求为基点,建设以公众为中心的电子政府,最后提出相应对策与建议,以利真正提高政府的绩效,让公众从中获得真正的收益.     

浅析增加农民收入的基本途径——对三农问题的几点思考

农民收入问题影响到农民的生活水平，影响到农业生产能力，是“三农”的根本问题。从农民、农村、农业三个角度提出了增加农民收入的对策建议。     

浅谈语言在馆员与读者沟通中的运用

阐述了正确运用符号语言与体态语言对改善馆员服务态度、提高馆员服务质量的重要作用。     

浅析新闻语言的弊病及其原因

新闻语言是通过新闻媒介,向人们报道新近发生的事实、传播新闻信息的载体之一。它作为媒体传递信息的工具,是一种对社会影响颇大的公共语言行为。时下新闻语言却出现了一系列的问题,已经严重的影响到新闻媒体的自身发展和社会用语的纯净。为了使新闻语言沿着科学、健康的方向发展,本文主要具体阐述了新闻语言弊病的表现形式和原因,希望能给新闻语言的规范提供帮助。     

由对诗人的重估到对新诗史的重构--从《诗刊》看五四以来的新诗传统在五、六十年代的命运

作为二十世纪五六十年代国内最权威的诗歌刊物《,诗刊》无疑代表了当时的文学潮流,并引领着文学的走向。研究自1957年1月到1965年停刊的《诗刊》,可以清晰地把握当时的诗坛动态和文学环境,不失为五六十年代中国文学的一份生动史料。本文着重考察的是《诗刊》如何以对“五四”以来新诗人的重估和对新诗史的重构,完成了新诗在五六十年代的历史叙述。