焊接速度对自适应双轴肩搅拌摩擦焊接Al–Mg合金接头微观组织和机械性能的影响

The butt welds of 4-mm thick 5A06 aluminum alloy plates were produced by adjustable-gap bobbin-tool friction stir travel with travel speeds of 200, 300, and 400 mm/min in this study. The microstructure was studied using optical microscopy and electron backscatter diffraction (EBSD). Tensile tests and microhardness measurements were performed to identify the effect of the travel speed on the joint mechanical properties. Sound joints were obtained at 200 mm/min while voids were present at different positions of the joints as the travel speed increased. The EBSD results show that the grain size, high angle grain boundaries, and density of geometrically necessary dislocations in different regions of the joint vary depending on the recovery and recrystallization behavior. Specific attention was given to the relationship between the local microstructure and mechanical properties. Microhardness measurements show that the average hardness of the stir zone (SZ) was greater than that of the base material, which was only affected slightly by the travel speed. The tensile strength of the joint decreased with increasing travel speed and the maximal strength efficiency reached 99%.     

基于EBSD数据，采用考虑各向异性效应的改进蒙特卡罗模型对冷轧超薄晶粒取向硅钢的再结晶过程进行了模拟

A Monte Carlo Potts model was developed to simulate the recrystallization process of a cold-rolled ultra-thin grain-oriented silicon steel. The orientation and image quality data from electron backscatter diffraction measurements were used as input information for simulation. Three types of nucleation mechanisms, namely, random nucleation, high-stored-energy site nucleation (HSEN), and high-angle boundary nucleation (HABN), were considered for simulation. In particular, the nucleation and growth behaviors of Goss-oriented ({011}<100>) grains were investigated. Results showed that Goss grains had a nucleation advantage in HSEN and HABN. The amount of Goss grains was the highest according to HABN, and it matched the experimental measurement. However, Goss grains lacked a size advantage across all mechanisms during the recrystallization process.     

电弧填丝增材制造高强度低合金钢的组织和力学性能

A high-building multi-directional pipe joint (HBMDPJ) was fabricated by wire and arc additive manufacturing using high-strength low-alloy (HSLA) steel. The microstructure characteristics and transformation were observed and analyzed. The results show that the forming part includes four regions. The solidification zone solidifies as typical columnar crystals from a molten pool. The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100°C, and the typical columnar crystals in this zone are difficult to observe. The partial austenitizing zone forms from the completely austenite zone heated between Ac1 (austenite transition temperature) and 1100°C, which is mainly equiaxed grains. After several thermal cycles, the partial austenitizing zone transforms to the tempering zone, which consistes of fully equiaxed grains. From the solidification zone to the tempering zone, the average grain size decreases from 75 to 20 μm. The mechanical properties of HBMDPJ satisfies the requirement for the intended application.     

烧结温度对纳米石墨烯增强ZA27基复合材料孔隙比和力学性能的影响

Nano graphene platelet (Gr) reinforced nano composites with a zinc–aluminum alloy (ZA27) matrix were produced by powder metallurgy at four different mass ratios (0.5wt%, 1.0wt%, 2.0wt% and 4.0wt%) and three different sintering temperatures (425, 450, and 475°C). In order to investigate the effect of sintering temperatures and nano graphene reinforcement materials on the composite structure, the microstructures of the composite samples were investigated and their densities were determined with a scanning electron microscope. Hardness, transverse rupture, and abrasion wear tests were performed to determine the mechanical properties. According to the test results, the porosity increased and the mechanical strength of the nano composites decreased as the amount of nano graphene reinforcement in ZA27 increased. However, when the composites produced in different reinforcement ratios were evaluated, the increase in sintering temperature increased the mechanical structure by positively affecting the composite structure.     

煤田火灾的形成机理及其探测和控制技术

Coalfield fires are considered a global crisis that contributes significantly to environmental destruction and loss of coal resources and poses a serious threat to human safety and health. In this paper, research related to the initiation, development, and evolution of coalfield fires is reviewed. The existing detection and control techniques of coalfield fires are also reviewed. Traditional firefighting is associated with waste of resources, potential risks of recrudescence, potential safety hazards, extensive and expensive engineering works, and power shortages. Recently, coalfield fires have been recognized as having significant potential for energy conservation and heat energy recovery. Thermoelectric power generation is regarded as a suitable technology for the utilization of heat from coalfield fires. The extraction of heat from coalfield fires can also control coalfield fires and prevent reignition leading to combustion. Technologies for absorbing heat from burning coal and overlying rocks are also analyzed. In addition, the control mode of “three-region linkage” is proposed to improve firefighting efficiency. Integrating heat energy recovery with firefighting is an innovative method to control coalfield fires.     

烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

关于农业区划地图集中的统一协调问题

图集的统一协调,对图集质量有很大影响。本文是作者在编制北京市农业区划地图集的实践基础上,根据地图信息传输论的观点,对农业区划地图集的统一协调的内容及方法进行了探讨。试图总结编制这类图集的统一协调模式,以供读者编图时参考。     

民间法正义观的转型

研究了国家法的抽象正义观与民间法的情理正义观,认为西方国家法的抽象正义观与东方民间法的情理正义观存在实质的不同,原因在于思维方式、超验与经验传统、政治结构的差别。在现代法治理念下,传统民间法所代表的正义观将向混合正义观转型,西方法治所代表的国家法抽象正义观是其骨架。     

“真空的真空”的存在性问题

许多科学家包括诺贝尔奖获得者李政道教授都预言,真空是未来物理学的一个重要研究对象.十七世纪的伽利略时代人们曾讨论过"真空"是否存在的问题.当时的学术界分成两派,一派以帕斯卡为代表,认为真空存在,另一派以笛卡尔为代表,认为真空不存在,最后实验证明"真空存在派"正确.现代研究表明,真空并非一无所有,这样就产生了一个新的问题"排除了真空物质后的空间",即"真空的真空"是否存在.本文探讨了与"真真空"有关的问题,提出了一些观测实验方法,这些方法可以帮助我们最终解答"真真空"的存在性问题.     

关于一维非自治时滞系统点态退化一例

给出了一维非自治时滞系统点态退化的一个例子,拓宽了该领域的研究。     

老年人生活空间移动性影响要素研究进展

 老年人生活空间移动性是老年人在日常生活中能动生活状态的重要表征。在梳理老年人生活空间移动性相关概念、测度方法基础上，分析了物质环境要素和非物质环境要素对老年人生活空间移动性的影响；提炼出有效支持老年人生活空间移动性的中观环境规划、微观环境设计和政策文化扶助层面的策略；指出了老年人生活空间移动性的研究建议和发展方向。     

人-自观念演进的否定之否定

在人与自然界的关系的演进过程中,形成了与不同文明时期相适应的人-自观念。从＂天人合一＂到＂人定胜天＂再到＂和谐共生＂,这是人-自观念演进的肯定、否定、否定之否定的辩证发展过程,也是一个合乎规律的过程,它们都是时代的产物,都包含着不同程度的合理的因素,我们必须对它们进行具体的辩证的分析。     

行政机关违法设定许可的法律责任探析

对于行政许可违法的法律责任问题，人们往往是从行政许可实施违法的角度进行研究，而对于设定违法及其责任追究的探讨却相对薄弱。然而。行政许可设定一旦违法，其对相对人和社会公共利益的损害将会更大，因此，对许可设定的违法及其责任问题进行研究，以避免违法行政行为的发生，促进政府依法行政，不仅必要而且是非常有意义的。     

曲面"侧"概念的"参照物"理解法

曲面“侧”是一个重要而难以理解的概念,本文对曲面“侧”概念的讲授方法进行了探讨,给出了曲面“侧”概念的“参照物”理解法,通过实践证明,效果良好。     

十二烷基苯硝化选择性的测定

利用对位异构体的对称性由核磁共振氢谱测定了工业十二烷基苯在硝硫混酸中的硝化选择性，发现一硝化产物中对位异构体的比例为７５％￣８０％。以月桂酸和苯为原料，经氯化、酰化和还原合成了正十二烷基苯。在同样条件下研究了正十二烷基苯的硝化，由核磁共振氢谱和气相色谱分析，发现一硝化产物中对位异构体的比例仅为６０％。根据空间位阻效应，对结果进行了讨论，并与甲苯，乙苯，异丙苯等短链烷基苯的硝化结果进行了比较。