烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

人工闪锌矿氧压酸浸过程中Cu2+的催化机理研究

The potential autoclave was used to study the catalytic mechanism of Cu2+ during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu2+ formed a CuS deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu2+. At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

超声振动辅助钨极惰性气体焊接异种金属 316L 和 L415

Ultrasonic vibration assisted tungsten inert gas welding was applied to joining stainless steel 316L and low alloy high strength steel L415. The effect of ultrasonic vibration on the microstructure and mechanical properties of a dissimilar metal welded joint of 316L and L415 was systematically investigated. The microstructures of both heat affected zones of L415 and weld metal were substantially refined, and the clusters of δ ferrite in traditional tungsten inert gas (TIG) weld were changed to a dispersive distribution via the ultrasonic vibration. The ultrasonic vibration promoted the uniform distribution of elements and decreased the micro-segregation tendency in the weld. With the application of ultrasonic vibration, the average tensile strength and elongation of the joint was improved from 613 to 650 MPa and from 16.15% to 31.54%, respectively. The content of Σ3 grain boundaries around the fusion line zone is higher and the distribution is more uniform in the ultrasonic vibration assisted welded joint compared with the traditional one, indicating an excellent weld metal crack resistance.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

关于中国西部村落生态智慧的理性阐释

在西方,提前消费观念的无限扩张和虚拟经济规模的毫无节制给世界经济带来严重冲击;在东方,人口快速增长给自然生态造成了不堪重负的压力。在虚拟经济泡沫不断破灭和持续发展推进艰难的现实峡谷之中,我们看到曾经被称为落后典型的＂自给自足＂乡村经济与民族文化的勃发生机。以＂村落生态智慧＂为代表的人与自然和谐共生的生存方式,其理论意义和承传价值理应成为支撑人类持续、健康、和谐发展不可缺少的智慧。     

浅析航海过失和管货过失

《海牙规则》确立了海运承运人对航海过失造成的货损免责，航海过失可分为驾船过失和管船过失。但承运人对管货过失造成的货损应承担赔偿责任。区分航海过失，尤其是管船过失与管货过失，成为一项极其重要的任务。近百的来，有关于此的争议不同涌现，国际上要求废除航海过失免责的呼声日益高涨，《汉堡规则》虽废除了航海过失免责，但亦未被国际社会所接受。文章探讨了航海过失与管货过失的区分标准，并尝试建立一种新的承运人责任制度。     

纳米技术的开发坚持以人为本之可能性

纳米技术的发展正如其他科学技术一样,必然给人类带来“双刃剑”效应。政府与企业、科学家都肩负着建立一个纳米技术发展的职业道德规范和约束的责任;在纳米技术开发中应坚持以人为本,这样才能保证纳米技术始终为人类文明的进步服务。     

浅析光绪朝漠河地区驱除金匪始末

光绪年间,黑龙江省漠河地区中俄金匪盗采现象尤甚,致使清政府损失了大量金矿资源。为了驱除金匪,保护本国矿产资源,清政府历经两年多艰苦卓绝的努力奋斗,投入大量人力、物力、财力才得以驱除以俄人为首的金匪。这不仅是中国历史上反抗外国经济侵略的一次抗争,还为中国漠河金矿的开办奠定了良好的开端。     

昔班尼王朝在中亚乌兹别克族形成中的作用

乌兹别克人穆罕默德·昔班尼于16世纪初期率其部民从钦察草原南下,在中亚建立了昔班尼王朝.经过几年的征服,该王朝包括河中地区、呼罗珊和花剌子模在内的大汗国.在昔班尼政权之下,中亚乌兹别克民族开始形成.昔班尼王朝在中亚乌兹别克族形成中起到了积极的作用.     

新时期中学教师师德修养浅谈

新时期中学教师应结合中学教师的角色特点,加强师德修养,诸如以身作则,以自己优良的品行教育和影响学生;热爱学生,建立新型的师生关系;加强学习,不断提高教育教学水平。     

论21世纪高校图书馆员的素质

21世纪高校图书馆员应具备良好的政治思想素与职业道德质和高层次的现代化知识素质,并通过继续教育来提高高校图书馆员的素质。     

伦理学视域中的尊严问题研究

伦理学意义上的尊严主要指社会行为主体人的尊严或者生命的尊严,与生命不可分割。人不仅是感性的肉体生命的存在,不仅是超越了自然理性的精神生命的存在,而且是牵涉肉体和精神的又赋予某种普遍性的社会生命的存在。在社会中,以人为主体便是生命尊严构成的必要条件,主体所承担的道德责任是人的尊严的体现。     

我国网络隐私权法律保护存在的问题及对策

随着计算机技术的飞速发展和互联网技术的迅速普及,侵犯网络隐私权的问题和矛盾日益突出,网络隐私权的法律保护成为当务之急。我们应综合考虑目前的立法状况和网络时代侵犯隐私权的特征,借鉴他国的先进经验并结合我国具体国情,完善我国网络隐私权立法,全面保护公民的网络隐私权。