焊接速度对自适应双轴肩搅拌摩擦焊接Al–Mg合金接头微观组织和机械性能的影响

The butt welds of 4-mm thick 5A06 aluminum alloy plates were produced by adjustable-gap bobbin-tool friction stir travel with travel speeds of 200, 300, and 400 mm/min in this study. The microstructure was studied using optical microscopy and electron backscatter diffraction (EBSD). Tensile tests and microhardness measurements were performed to identify the effect of the travel speed on the joint mechanical properties. Sound joints were obtained at 200 mm/min while voids were present at different positions of the joints as the travel speed increased. The EBSD results show that the grain size, high angle grain boundaries, and density of geometrically necessary dislocations in different regions of the joint vary depending on the recovery and recrystallization behavior. Specific attention was given to the relationship between the local microstructure and mechanical properties. Microhardness measurements show that the average hardness of the stir zone (SZ) was greater than that of the base material, which was only affected slightly by the travel speed. The tensile strength of the joint decreased with increasing travel speed and the maximal strength efficiency reached 99%.     

基于EBSD数据，采用考虑各向异性效应的改进蒙特卡罗模型对冷轧超薄晶粒取向硅钢的再结晶过程进行了模拟

A Monte Carlo Potts model was developed to simulate the recrystallization process of a cold-rolled ultra-thin grain-oriented silicon steel. The orientation and image quality data from electron backscatter diffraction measurements were used as input information for simulation. Three types of nucleation mechanisms, namely, random nucleation, high-stored-energy site nucleation (HSEN), and high-angle boundary nucleation (HABN), were considered for simulation. In particular, the nucleation and growth behaviors of Goss-oriented ({011}<100>) grains were investigated. Results showed that Goss grains had a nucleation advantage in HSEN and HABN. The amount of Goss grains was the highest according to HABN, and it matched the experimental measurement. However, Goss grains lacked a size advantage across all mechanisms during the recrystallization process.     

电弧填丝增材制造高强度低合金钢的组织和力学性能

A high-building multi-directional pipe joint (HBMDPJ) was fabricated by wire and arc additive manufacturing using high-strength low-alloy (HSLA) steel. The microstructure characteristics and transformation were observed and analyzed. The results show that the forming part includes four regions. The solidification zone solidifies as typical columnar crystals from a molten pool. The complete austenitizing zone forms from the solidification zone heated to a temperature greater than 1100°C, and the typical columnar crystals in this zone are difficult to observe. The partial austenitizing zone forms from the completely austenite zone heated between Ac1 (austenite transition temperature) and 1100°C, which is mainly equiaxed grains. After several thermal cycles, the partial austenitizing zone transforms to the tempering zone, which consistes of fully equiaxed grains. From the solidification zone to the tempering zone, the average grain size decreases from 75 to 20 μm. The mechanical properties of HBMDPJ satisfies the requirement for the intended application.     

烧结温度对纳米石墨烯增强ZA27基复合材料孔隙比和力学性能的影响

Nano graphene platelet (Gr) reinforced nano composites with a zinc–aluminum alloy (ZA27) matrix were produced by powder metallurgy at four different mass ratios (0.5wt%, 1.0wt%, 2.0wt% and 4.0wt%) and three different sintering temperatures (425, 450, and 475°C). In order to investigate the effect of sintering temperatures and nano graphene reinforcement materials on the composite structure, the microstructures of the composite samples were investigated and their densities were determined with a scanning electron microscope. Hardness, transverse rupture, and abrasion wear tests were performed to determine the mechanical properties. According to the test results, the porosity increased and the mechanical strength of the nano composites decreased as the amount of nano graphene reinforcement in ZA27 increased. However, when the composites produced in different reinforcement ratios were evaluated, the increase in sintering temperature increased the mechanical structure by positively affecting the composite structure.     

煤田火灾的形成机理及其探测和控制技术

Coalfield fires are considered a global crisis that contributes significantly to environmental destruction and loss of coal resources and poses a serious threat to human safety and health. In this paper, research related to the initiation, development, and evolution of coalfield fires is reviewed. The existing detection and control techniques of coalfield fires are also reviewed. Traditional firefighting is associated with waste of resources, potential risks of recrudescence, potential safety hazards, extensive and expensive engineering works, and power shortages. Recently, coalfield fires have been recognized as having significant potential for energy conservation and heat energy recovery. Thermoelectric power generation is regarded as a suitable technology for the utilization of heat from coalfield fires. The extraction of heat from coalfield fires can also control coalfield fires and prevent reignition leading to combustion. Technologies for absorbing heat from burning coal and overlying rocks are also analyzed. In addition, the control mode of “three-region linkage” is proposed to improve firefighting efficiency. Integrating heat energy recovery with firefighting is an innovative method to control coalfield fires.     

烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

不同硅饱和系数水榴石的碳酸化分解动力学

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method, which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method. In this study, the effect of the silica saturation coefficient (x) on the carbonation of hydrogarnet was investigated from the kinetic perspective. The results indicated that the carbonation of hydrogarnets with different x values (x = 0.27, 0.36, 0.70, and 0.73) underwent two stages with significantly different rates, and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3. The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol, respectively. Moreover, the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.     

一种超重力燃烧合成制备高性能高熵合金的新方法

A new method of high-gravity combustion synthesis (HGCS) followed by post-treatment (PT) is reported for preparing high-performance high-entropy alloys (HEAs), Cr_0.9FeNi_2.5V_0.2Al_0.5 alloy, whereby cheap thermite powder is used as the raw material. In this process, the HEA melt and the ceramic melt are rapidly formed by a strong exothermic combustion synthesis reaction and completely separated under a high-gravity field. Then, the master alloy is obtained after cooling. Subsequently, the master alloy is sequentially subjected to conventional vacuum arc melting (VAM), homogenization treatment, cold rolling, and annealing treatment to realize a tensile strength, yield strength, and elongation of 1250 MPa, 1075 MPa, and 2.9%, respectively. The present method is increasingly attractive due to its low cost of raw materials and the intermediate product obtained without high-temperature heating. Based on the calculation of phase separation kinetics in the high-temperature melt, it is expected that the final alloys with high performance can be prepared directly across master alloys with higher high-gravity coefficients.     

窄板坯结晶器内连铸工艺参数对钢液流场的影响

Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting (CC) molds with narrow widths for the production of automobile exposed panels. Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process. The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold. Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone. The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min?1 and casting speed of 1.7 m·min?1. Under the present experimental conditions, the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.     

电渣重熔脱硫技术研究进展

Electroslag remelting (ESR) gives a combination of liquid metal refining and solidification structure control. One of the typical aspects of liquid metal refining during ESR for the advanced steel and alloy production is desulfurization. It involves two patterns, i.e., slag–metal reaction and gas–slag reaction (gasifying desulfurization). In this paper, the advances in desulfurization practices of ESR are reviewed. The effects of processing parameters, including the initial sulfur level of consumable electrode, remelting atmosphere, deoxidation schemes of ESR, slag composition, melting rate, and electrical parameters on the desulfurization in ESR are assessed. The interrelation between desulfurization and sulfide inclusion evolution during ESR is discussed, and advancements in the production of sulfur-bearing steel at a high-sulfur level during ESR are described. The remaining challenges for future work are also proposed.     

利用皮秒激光烧蚀制备非球形铝纳米颗粒

We report the picosecond laser ablation of aluminum targets immersed in a polar organic liquid (chloroform, CHCl₃) with ~2 ps laser pulses at an input energy of ~350 μJ. The synthesized aluminum nanoparticles exhibited a surface plasmon resonance peak at ~340 nm. Scanning electron microscopy images of Al nanoparticles demonstrated the spherical morphology with an average size of (27 ± 3.6) nm. The formation of smaller spherical Al nanoparticles and the diminished growth could be from the formation of electric double layers on the Al nanoparticles. In addition to spherical aluminum nanoparticles, triangular/pentagonal/hexagonal nanoparticles were also observed in the colloidal solution. Field emission scanning electron microscopy images of ablated Al targets demonstrated laser induced periodic surface structures (LIPSSs), which were the high spatial frequency LIPSSs (HSF-LIPSSs) since their grating period was ~280 nm. Additionally, coarse structures with a period of ~700 nm were observed.     

基于云模型和混合半定量决策方法的闭矿风险管理

Mine closure is associated with many negative impacts on society and the environment. If these effects are not rationally addressed, they would pose risks of mine closure. Thus, a risk management method is needed to mitigate these adverse impacts and address mine-closure issues. An integral framework for mine-closure risk management that includes risk assessment and risk treatment was proposed. Given the fuzziness and randomness of the transformation between qualitative and quantitative knowledge in the risk assessment process, a novel risk assessment method based on the cloud model was presented, which fully considers the uncertainty in risks themselves and in the reasoning process. Closed mine reutilization is an effective risk treatment option in response to the identified high risks, but it requires selecting optimal reutilization strategies for the successful implementation of the reuse plan. To this end, a hybrid semi-quantitative decision method is proposed to optimize decision-making. The results of a case study showed that this risk management methodology can help budget planning for risk treatment and provide an instructional framework to effectively reduce the negative effects of closed mines.     

塑性应变和成型温度对低碳钢磁性能的影响

Claw poles are a key component of automobile generators. The output power performance of the generator is very dependent on the magnetic properties of its claw poles. Plastic deformation is known to significantly change the magnetic behavior of ferromagnetic materials in claw poles. In this paper, changes in the magnetic properties of low-carbon steel, used for claw pole components due to their plastic deformation, were investigated for different strains and temperatures. Ring-shaped material samples were prepared by machining and their magnetic properties were measured. The surface roughness was first evaluated and a machining process with an arithmetic average of roughness Ra 1.6 μm was selected as enabling the lowest measurement error. Hysteresis loops at different applied magnetic fields of the material were obtained for different plastic strains and forming temperatures. The magnetic parameters of magnetic flux density, coercivity, and remanence were obtained and compared with magnetic flux density as the primary focus. Results showed that machining, cold forming, and hot forming all led to lower magnetic flux density, larger coercivity, and smaller remanence. Magnetic flux density showed a sharp decrease at the start of plastic deformation, but as the strain increased, the decreasing trend gradually reached a constant value. The decrease was much larger for cold forming than for hot forming. For example, at 500 A/m, the degradation of magnetic flux density with a reduction percentage of 5% at room temperature was about 50%, while that of hot forming at 1200°C was about 10%. Results of this research may provide a reference for the future process design of hot-forged claw poles.     

用于低品位热能储蓄的盐浸渍阳极氧化铝复合材料的合成与表征

Thermochemical heat storage (THS) systems have recently attracted a lot of attention in research and development. In this study, an anodic aluminum oxide (AAO) template, fabricated by a two-step anodization method, was used for the first time as the matrix material for a THS system. Different salts were studied as thermochemical materials for their suitability in low-grade heat storage application driven by solar energy for an open system. Compositions were prepared by absorbing CaCl₂, MgCl₂, LiCl, LiNO₃ and mixtures of these salts under a vacuum in an AAO matrix. Field Emission Scanning Electron Microscopy was used to examine the morphology of the produced AAO composites. Thermal energy storage capacities of the composites were characterized using a differential scanning calorimeter. Characterization analysis showed that anodized Al plates were suitable matrix materials for THS systems, and composite sorbent prepared with a 1:1 ratio LiCl/LiNO₃ salt mixture had the highest energy value among all composites, with an energy density of 468.1 kJ·kg?1.     

通过高温预处理高磷鲕状赤铁矿实现铁富集和脱磷

The efficient development and utilization of high-phosphorus oolitic hematite is of great strategic significance for the sustainable supply of iron-ore resources in China. In this paper, the mechanism of high-temperature pretreatment for enhancing the effect of iron enrichment and dephosphorization in the magnetization roasting–leaching process was studied by X-ray diffraction (XRD), vibration sample magnetometer (VSM), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Compared with the process without high-temperature pretreatment, the iron grade of the magnetic separation concentrate after high-temperature pretreatment had increased by 0.98%, iron recovery rate had increased by 1.33%, and the phosphorus content in the leached residue had decreased by 0.12%. High-temperature pretreatment resulted in the dehydration and decomposition of hydroxyapatite, the dehydration of limonite and the thermal decomposition of siderite, which can produce pores and cracks and weaken the compactness of the ore, improve the magnetization characteristics of roasted ore, and strengthen the iron enrichment and dephosphorization during the magnetization roasting and leaching process.     

结晶器内电磁搅拌对结晶器表面负偏析影响的模型预测

Aiming at the problem of negative segregation under a bloom surface, a coupling macrosegregation model considering electromagnetic field, flow, heat, and solute transport was established based on the volume average method to study the effect of in-mold electromagnetic stirring (M-EMS) on the negative segregation under the bloom surface. In the model, the influence of dendrite structure on the flow and solute transport was described by the change of permeability. The model was validated by the magnetic induction intensity of M-EMS and carbon segregation experiment. The results show that the solute C in the solidified shell in the turbulent zone of the bloom undergoes two negative segregations, whereby the first is caused by nozzle jet, and the second by the M-EMS. The severities of the negative segregation caused by M-EMS at different currents and frequencies are also different, and the larger the current is, or the smaller the frequency is, the more serious will be the negative segregation. With the M-EMS, the solute C distribution in the liquid phase of the bloom is more uniform, but the mass fraction of C in the liquid phase is higher than that without M-EMS.