烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

含钛高炉炉渣微波合成碳化钛及其介电性能测定

The preparation of functional material titanium carbide by the carbothermal reduction of Ti-bearing blast furnace slag with microwave heating is an effective method for valuable metals recovery; it can alleviate the environmental pressure caused by slag stocking. The dynamic dielectric parameters of Ti-bearing blast furnace slag/pulverized coal mixture under high-temperature heating are measured by the cylindrical resonant cavity perturbation method. Combining the transient dipole and large π bond delocalization polarization phenomena, the interaction mechanism of the microwave macroscopic non-thermal effect on the titanium carbide synthesis reaction was revealed. The material thickness range during microwave heating was optimized by the joint analysis of penetration depth and reflection loss, which is of great significance to the design of the microwave reactor for the carbothermal reduction of Ti-bearing blast furnace slag.     

对图书馆读者满意度问题的思考

分析了图书馆读者满意度的含义及衡量要素,论述了图书馆调查读者满意度的目的及方式,提出了图书馆提升读者满意度的策略。     

会计信息复杂性与财务估价修正

分析了会计信息复杂性的各种表现及其成因,在收集会计信息复杂性对公司价值产生负面影响的实证证据的基础上,提出了对财务估价模型进行修正的解决思路,并给出了降低会计信息复杂性的若干建议。     

柴油机缸套穴蚀产生的机理

探讨柴油机缸套产生穴蚀的机理,分析了柴油机活塞、缸套、冷却系等零部件一结构、安装、配合和使用情况对缸套穴蚀的影响。     

桥梁混凝土结构裂缝成因探讨

分析了混凝土桥梁裂缝的种类和产生的原因,提出了在施工中控制裂缝的可行办法。     

元数据对专利自动分类准确度的影响

在介绍专利自动分类的计算模型基础上,总结了元数据对专利自动分类的作用,分析了元数据对专利自动分类准确度的影响。     

从美国硅谷银行模式看我国科技银行未来发展

在辩证分析美国硅谷银行经营模式的基础上,简要回顾了我国科技银行的发展历程、现状及不足,并对我国科技银行未来发展的路径选择提出了对策建议。     

战斗部侧弦攻击舰船内爆毁伤能力评估

建立了舰船内爆毁伤的静爆试验方法,并基于该方法建立了数值模型。通过实验分析与数值模拟,获取了战斗部内爆产生的冲击波超压和破片毁伤参数,分析了冲击波超压对主、临舱室人员的毁伤情况及破片的主要毁伤范围,为战斗部对相同舰船目标的毁伤威力及毁伤评估提供参考依据。     

高速公路沥青路面早期破坏的原因分析

在调研的基础上归纳了高速公路沥青路面早期破坏的类型,详细分析了高速公路沥青路面早期破坏的原因。     

叶轮进口边位置对自吸泵性能的影响分析

为研究自吸泵叶轮气液混合能力对自吸性能的影响,在叶轮原模型基础上,设计了叶片不同进口边位置的5种模型方案.采用VOF多相流模型对不同方案全流域进行三维定常数值计算,研究对自吸性能的影响规律.针对350WFB-1200-50型外混式无密封自吸泵,初始条件设定进水S型弯管中含一定体积的空气段,出口处设置含气率监测点.结果表明:针对中高比转速叶轮,进口边沿后盖板位置向出口前掠,使得叶轮进口边工作时对流体分时加载,可以有效提升叶轮的气液混合能力,从而缩短自吸泵的自吸时间;在一定前掠角度范围内改变进口边位置对自吸泵的扬程和效率影响不大,但是当叶片进口边向出口位置前掠超过一定范围时,会导致自吸泵扬程明显下降;当叶轮进口边前掠10°时,额定工况下自吸时间缩短25％,自吸性能明显得到提高.     

箱拱梁体裂缝成因分析及预防

针对施工中出现的梁体裂缝情况，在详细分析与探讨梁体裂缝产生原因的基础上，提出了具体的预防措施。