烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

不同硅饱和系数水榴石的碳酸化分解动力学

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method, which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method. In this study, the effect of the silica saturation coefficient (x) on the carbonation of hydrogarnet was investigated from the kinetic perspective. The results indicated that the carbonation of hydrogarnets with different x values (x = 0.27, 0.36, 0.70, and 0.73) underwent two stages with significantly different rates, and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3. The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol, respectively. Moreover, the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.     

一种超重力燃烧合成制备高性能高熵合金的新方法

A new method of high-gravity combustion synthesis (HGCS) followed by post-treatment (PT) is reported for preparing high-performance high-entropy alloys (HEAs), Cr_0.9FeNi_2.5V_0.2Al_0.5 alloy, whereby cheap thermite powder is used as the raw material. In this process, the HEA melt and the ceramic melt are rapidly formed by a strong exothermic combustion synthesis reaction and completely separated under a high-gravity field. Then, the master alloy is obtained after cooling. Subsequently, the master alloy is sequentially subjected to conventional vacuum arc melting (VAM), homogenization treatment, cold rolling, and annealing treatment to realize a tensile strength, yield strength, and elongation of 1250 MPa, 1075 MPa, and 2.9%, respectively. The present method is increasingly attractive due to its low cost of raw materials and the intermediate product obtained without high-temperature heating. Based on the calculation of phase separation kinetics in the high-temperature melt, it is expected that the final alloys with high performance can be prepared directly across master alloys with higher high-gravity coefficients.     

窄板坯结晶器内连铸工艺参数对钢液流场的影响

Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting (CC) molds with narrow widths for the production of automobile exposed panels. Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process. The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold. Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone. The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min?1 and casting speed of 1.7 m·min?1. Under the present experimental conditions, the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.     

电渣重熔脱硫技术研究进展

Electroslag remelting (ESR) gives a combination of liquid metal refining and solidification structure control. One of the typical aspects of liquid metal refining during ESR for the advanced steel and alloy production is desulfurization. It involves two patterns, i.e., slag–metal reaction and gas–slag reaction (gasifying desulfurization). In this paper, the advances in desulfurization practices of ESR are reviewed. The effects of processing parameters, including the initial sulfur level of consumable electrode, remelting atmosphere, deoxidation schemes of ESR, slag composition, melting rate, and electrical parameters on the desulfurization in ESR are assessed. The interrelation between desulfurization and sulfide inclusion evolution during ESR is discussed, and advancements in the production of sulfur-bearing steel at a high-sulfur level during ESR are described. The remaining challenges for future work are also proposed.     

利用皮秒激光烧蚀制备非球形铝纳米颗粒

We report the picosecond laser ablation of aluminum targets immersed in a polar organic liquid (chloroform, CHCl₃) with ~2 ps laser pulses at an input energy of ~350 μJ. The synthesized aluminum nanoparticles exhibited a surface plasmon resonance peak at ~340 nm. Scanning electron microscopy images of Al nanoparticles demonstrated the spherical morphology with an average size of (27 ± 3.6) nm. The formation of smaller spherical Al nanoparticles and the diminished growth could be from the formation of electric double layers on the Al nanoparticles. In addition to spherical aluminum nanoparticles, triangular/pentagonal/hexagonal nanoparticles were also observed in the colloidal solution. Field emission scanning electron microscopy images of ablated Al targets demonstrated laser induced periodic surface structures (LIPSSs), which were the high spatial frequency LIPSSs (HSF-LIPSSs) since their grating period was ~280 nm. Additionally, coarse structures with a period of ~700 nm were observed.     

叶轮进口边位置对自吸泵性能的影响分析

为研究自吸泵叶轮气液混合能力对自吸性能的影响,在叶轮原模型基础上,设计了叶片不同进口边位置的5种模型方案.采用VOF多相流模型对不同方案全流域进行三维定常数值计算,研究对自吸性能的影响规律.针对350WFB-1200-50型外混式无密封自吸泵,初始条件设定进水S型弯管中含一定体积的空气段,出口处设置含气率监测点.结果表明:针对中高比转速叶轮,进口边沿后盖板位置向出口前掠,使得叶轮进口边工作时对流体分时加载,可以有效提升叶轮的气液混合能力,从而缩短自吸泵的自吸时间;在一定前掠角度范围内改变进口边位置对自吸泵的扬程和效率影响不大,但是当叶片进口边向出口位置前掠超过一定范围时,会导致自吸泵扬程明显下降;当叶轮进口边前掠10°时,额定工况下自吸时间缩短25％,自吸性能明显得到提高.     

由对诗人的重估到对新诗史的重构--从《诗刊》看五四以来的新诗传统在五、六十年代的命运

作为二十世纪五六十年代国内最权威的诗歌刊物《,诗刊》无疑代表了当时的文学潮流,并引领着文学的走向。研究自1957年1月到1965年停刊的《诗刊》,可以清晰地把握当时的诗坛动态和文学环境,不失为五六十年代中国文学的一份生动史料。本文着重考察的是《诗刊》如何以对“五四”以来新诗人的重估和对新诗史的重构,完成了新诗在五六十年代的历史叙述。     

湿度传感器稳定性的误差来源分析

阐述了湿度传感器稳定性的误差,指出影响湿度传感器稳定性的误差有线性误差、温度影响误差、湿滞误差以及校验标准误差等.     

技术异化的生成

从技术的复杂性和局限性、技术的不恰当使用、自然的不可预见性、技术理性的沙文主义式扩展及社会文化等几个方面探讨了技术异化产生的根源。     

对图书馆读者满意度问题的思考

分析了图书馆读者满意度的含义及衡量要素,论述了图书馆调查读者满意度的目的及方式,提出了图书馆提升读者满意度的策略。     

业务外包对图书馆可持续发展的影响

介绍了目前图书馆业务外包的外延和内涵,论述了业务外包之后的图书馆办馆效益,分析了业务外包带来的问题,对业务外包后的图书馆事业可持续发展进行了思考。     

迎接知识经济的挑战 加强高校图书馆建设

在知识经济的背景下,图书馆的工作职能将发生显著变革,知识经济时代图书馆将面临新的机遇与挑战。图书馆要适应知识经济的需要,就必须加强自身建设,提高人才素质是决定性因素;网络建设是必由之路;现代化的科学管理是关键环节。     

关于中小企业信息化建设问题的再思考

阐述了中小企业内部存在的阻碍信息化建设的不利因素,介绍了企业信息化的3个阶段以及中小企业信息化实施的一般步骤,提出了中小企业应关注的信息化的几个问题以及中小企业实施信息化的一般策略,指出中小企业提高企业管理水平和决策水平的行之有效的方法是循序渐进地推进信息化的建设。     

医疗体育对大学生身高增长的影响

19至24岁的大学生,随着内脏器官的不断完善,两次身高增长的高峰期已经过去,一但骨骺部位闭合,骨化,身高的增长就几乎停止。通过对815名学生样本数据的正态分析和对中外多项增高实例研究,对比,得出大学生群体中身材矮小及伴随相关心问题的人,通过有针对性的体疗锻炼,能使其形体和心理都得到有效的改善。对大学生身体发育抢救阶段,医疗体育（体疗）方案,运动处方,增高器械等方面的深入探索,对培养高素质人才具有深远的意义。     

Change in the tilting of the ridgeline surface of the subtropical anticyclone and the predictability of the onset of the Asian summer monsoon

The NCEP/NCAR reanalysis data are used to study the relationships among the change in the tilting of the ridgeline surface of the subtropical anticyclone, the establishment of the so-called "seasonal transition axis (STA)" and the onset of the Asian summer monsoon. It is shown that the monsoon onset is characterized by the overturning of the meridional temperature gradient (MTG) in the vicinity of the ridgeline surface. A MTG index is then constructed to investigate the predictability of the Asian summer monsoon onset conceptually. Data diagnoses show that if the initial MTG is known and the meridional gradient across the ridgeline surface of the local temperature tendency can be estimated, a late or early onset of the summer monsoon can be qualitatively predicted in advance.