云芝漆酶理化性质及动力学研究

主要研究pH值、金属离子、温度对云芝漆酶活性和稳定性的影响,以及该酶底物浓度效应和Km值测定.实验结果表明:Cu2+、Co2+对漆酶有激活作用,而Ag+则有抑制作用;该酶最适pH为4.8,在pH4~4.8表现出较强的稳定性;最适反应温度为40℃,低于50℃时有较好的热稳定性;Km值为4.2×10-3mol/L.     

溴酸钾存在下苯丙氨酸的极谱催化波研究

在0.10mol/L LiCl-0.02mol/L HCl-8.0×10-3mol/L KBrO3支持电解质中,苯丙氨酸产生一个极谱催化波,峰电位为-1.65V(vs.SCE).该极谱催化波二阶导数峰电流与苯丙氨酸的浓度在2.0×10-5～2.5×10-3mol/L范围呈线性关系,其检测下限为6.5×10-6mol/L.本文建立了苯丙氨酸的分析测定方法,讨论了该极谱催化波的产生机理.     

吸附溶出催化伏安法测定痕量锗的研究

提出了吸附溶出催化伏安法测定痕量锗的方法。该方法最佳体系为0.15 mol/L KCl+1.0×10~(-3) mol/L 3,4-二羟基苯甲醛(DHB)+2.0×10~(-3)mol/L EDTA+3.0×10~(-3)mol/L V(Ⅳ),pH2.15。其线性范围为1.2×10~(-10)～6.O×10~(-8)mol/L,最低检出浓度为3.6×10~(-11)mol/L Ge(Ⅳ)。     

催化动力学分光光度法测定镨和钐

在盐酸介质中,痕量稀土元素镨和钐催化双氧水氧化碘化钾生成单质碘,单质碘可使次甲基蓝褪色,基于此建立了催化动力学分光光度法测定稀土元素镨和钐的新方法.方法的线性范围分别为5.1×10-6mol/L～5.1×10-5mol/L、5.1×10-6mol/L～5.1×10-5mol/L,检出限分别为2.75×10-6mol/L和2.44×10-6mol/L.该方法用于含稀土的纳米材料中镨和钐的分析测定,结果满意.     

聚组氨酸修饰电极测定多巴胺的研究

本文研究了多巴胺在聚组氨酸修饰电极上的循环伏安行为.在pH7.0的磷酸盐缓冲溶液中,用线形扫描伏安法测定多巴胺的线性范围为:6.0×10-8～1.0×10-5mol/L,1.5×10-5～1.0×10-3mol/L,检出限为4×10-8mol/L.用于药剂中多巴胺的测定,结果满意.     

一种麦芽酸性磷酸酶的分离纯化及部分性质研究

经硫酸铵分级沉淀、CM-Sepharose CL 4B和DEAE-Sepharose CL 4B离子交换柱层析等步骤,从麦芽中分离提纯到一种酸性磷酸酶(ACPase,E．C．3．1．3．2),纯化倍数为33．06,酶液比活为88．27 U/mg．通过动力学方法测得其最适pH为5．4,酸碱稳定性较差,仅在pH 6．0左右的缓冲液中较稳定;最适温度为50 ℃,40 ℃以下有较好的稳定性;在最适条件下,该酶催化pNPP的米氏常数(Km)为4．696×10-4 mol/L．同时研究了一些金属离子和有机化合物对该酶     

朊圆酵母Y0401尿酸酶的基本特性研究

研究了尿酸酶分离纯化条件和pH、温度、底物浓度、一些有机和无机试剂对尿酸酶酶促反应速度的影响.研究结果表明,用Triton X-100及巯基乙醇处理细胞悬液(pH 8.5),再用超声波处理破碎细胞效果最佳.硫酸铵沉淀尿酸酶的最佳浓度为75%.用Phenyl-Sepharose CL-4B疏水层析和Xanthine-agarose亲和层析两步纯化步骤可获得理想纯度的酶制剂.在一定的条件下,尿酸酶的最适pH和酸碱稳定pH范围分别为8.5和5.0～12.最适温度为37℃;热稳定性较好,在50℃处理30 min时活性保持90%,在60℃处理30min时活性仍保持80%.在最适条件下,该酶催化尿酸的米氏常数(Km)为3.34×10-5mol/L.一些金属离子和有机化合物对酶活性的影响也进行了研究.     

喹啉的极谱催化波及其应用

在0.15mol/L HAc-NaAc(pH 4.4)-0.016mol/L KIO3支持电解质中,喹啉产生一灵敏的极谱催化波,峰电流比其相应的极谱波增大30余倍,峰电位为-1.14V(vs.SCE).该极谱催化波的二阶导数峰电流与其浓度在1.0×10-4～3.5×10-4mol/L范围内呈线性关系,检测下限为2.0×10-5 mol/L,该方法可用于微量喹啉的测定,其灵敏度比无KIO3存在时提高了近一个数量级.     

中国黑白花优良种公牛精子透明质酸酶的分离纯化及部分性质研究

中国黑白花优良种公牛精子透明质酸酶经硫酸铵分级沉淀和 Sephadex 柱层析分离纯化,得到一个电泳纯品,活力纯化40倍.用 sephadexG-150凝胶过滤和 SDS—聚丙烯酰胺凝胶电泳测得分子量为65000.该酶的最适 pH 为3.5～4.5,最适温度为37℃～45℃,在室温下较稳定,用 Limeweaver-Burk 作图法求得 Km 值为6.06×10~(-4)mol/L.     

谷氨酸生产菌T6—13谷氨酸脱氢酶特性研究

本文对谷氨酸生产菌Te_(-13)谷氨酸脱氢酶的辅酶专一性、热稳定性、最适温度、最适pH、动力学参数和发酵过程中酶活力变化进行了研究。结果表明该酶属胞内酶,以NADP~+为专一性辅酶,脱氨反应的最适pH为9.5,酶的最适温度为35～40℃,酶的热稳定性试验表明50℃保温10分钟,残留活力为50%,60℃保温10分钟残留活力为4%,70℃下则完全丧失活力,对L—谷氨酸和NADP~+动力学参数分别为2.13×10.2mol/L和6.58×10~(-5)mol/L,AMP、ADP对脱氨反应有激活作用,ATP无影响。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.