烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

氧化锌矿物浸出渣中铅、锶的提取及动力学分析

NH₄HCO₃ conversion followed by HCl leaching was performed and proven to be effective in extracting Pb and Sr from zinc extracted residual. The mechanism and operating conditions of NH₄HCO₃ conversion, including molar ratio of NH₄HCO₃ to zinc extracted residual, NH₄HCO₃ concentration, conversion temperature, conversion time, and stirring velocity, were discussed, and operating conditions were optimized by the orthogonal test. Experimental results indicate that NH₄HCO₃ conversion at temperatures ranging from 25 to 85°C follows the shrinking unreacted core model and is controlled by inner diffusion through the product layer. The extraction ratios of Pb and Sr under optimized conditions reached 85.15% and 87.08%, respectively. Moreover, the apparent activation energies of Pb and Sr were 13.85 and 13.67 kJ·mol?1, respectively.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

叶轮进口边位置对自吸泵性能的影响分析

为研究自吸泵叶轮气液混合能力对自吸性能的影响,在叶轮原模型基础上,设计了叶片不同进口边位置的5种模型方案.采用VOF多相流模型对不同方案全流域进行三维定常数值计算,研究对自吸性能的影响规律.针对350WFB-1200-50型外混式无密封自吸泵,初始条件设定进水S型弯管中含一定体积的空气段,出口处设置含气率监测点.结果表明:针对中高比转速叶轮,进口边沿后盖板位置向出口前掠,使得叶轮进口边工作时对流体分时加载,可以有效提升叶轮的气液混合能力,从而缩短自吸泵的自吸时间;在一定前掠角度范围内改变进口边位置对自吸泵的扬程和效率影响不大,但是当叶片进口边向出口位置前掠超过一定范围时,会导致自吸泵扬程明显下降;当叶轮进口边前掠10°时,额定工况下自吸时间缩短25％,自吸性能明显得到提高.     

由对诗人的重估到对新诗史的重构--从《诗刊》看五四以来的新诗传统在五、六十年代的命运

作为二十世纪五六十年代国内最权威的诗歌刊物《,诗刊》无疑代表了当时的文学潮流,并引领着文学的走向。研究自1957年1月到1965年停刊的《诗刊》,可以清晰地把握当时的诗坛动态和文学环境,不失为五六十年代中国文学的一份生动史料。本文着重考察的是《诗刊》如何以对“五四”以来新诗人的重估和对新诗史的重构,完成了新诗在五六十年代的历史叙述。     

技术异化的生成

从技术的复杂性和局限性、技术的不恰当使用、自然的不可预见性、技术理性的沙文主义式扩展及社会文化等几个方面探讨了技术异化产生的根源。     

湿度传感器稳定性的误差来源分析

阐述了湿度传感器稳定性的误差,指出影响湿度传感器稳定性的误差有线性误差、温度影响误差、湿滞误差以及校验标准误差等.     

对图书馆读者满意度问题的思考

分析了图书馆读者满意度的含义及衡量要素,论述了图书馆调查读者满意度的目的及方式,提出了图书馆提升读者满意度的策略。     

业务外包对图书馆可持续发展的影响

介绍了目前图书馆业务外包的外延和内涵,论述了业务外包之后的图书馆办馆效益,分析了业务外包带来的问题,对业务外包后的图书馆事业可持续发展进行了思考。     

迎接知识经济的挑战 加强高校图书馆建设

在知识经济的背景下,图书馆的工作职能将发生显著变革,知识经济时代图书馆将面临新的机遇与挑战。图书馆要适应知识经济的需要,就必须加强自身建设,提高人才素质是决定性因素;网络建设是必由之路;现代化的科学管理是关键环节。     

医疗体育对大学生身高增长的影响

19至24岁的大学生,随着内脏器官的不断完善,两次身高增长的高峰期已经过去,一但骨骺部位闭合,骨化,身高的增长就几乎停止。通过对815名学生样本数据的正态分析和对中外多项增高实例研究,对比,得出大学生群体中身材矮小及伴随相关心问题的人,通过有针对性的体疗锻炼,能使其形体和心理都得到有效的改善。对大学生身体发育抢救阶段,医疗体育（体疗）方案,运动处方,增高器械等方面的深入探索,对培养高素质人才具有深远的意义。     

关于汉族民歌体裁的分类问题

目前,汉族民歌体裁的分类存在着多种分类依据并存的现象,如果长期达不到共识,民歌体裁的分类研究就名存实亡。因此,必须对民歌音乐上的种种特征进行不同角度归纳和整理。汉族民歌在音乐形态上有共性,那么,体裁的划分依据应以音乐形态特征为主,应划分开质与量的区别,能分离质的不同而包容量的差异,将民间文化不断丰富、发展、生生不息的因素考虑在其中,形成一个能概括汉族各地民歌体裁类型的分类方法和标准。     

关于中小企业信息化建设问题的再思考

阐述了中小企业内部存在的阻碍信息化建设的不利因素,介绍了企业信息化的3个阶段以及中小企业信息化实施的一般步骤,提出了中小企业应关注的信息化的几个问题以及中小企业实施信息化的一般策略,指出中小企业提高企业管理水平和决策水平的行之有效的方法是循序渐进地推进信息化的建设。