热处理对粉末注射成形钛合金的组织与性能的影响

采用粉末注射成形方法制备了钛合金坯体,利用溶剂脱脂和热脱脂方法脱除坯体中粘结剂,并在真空气氛下烧结致密钛合金样品.真空烧结后,经960 ℃和140 MPa热等静压处理,在720～760 ℃进行1～1.5 h退火处理获得的样品微观结构为均匀的双态组织,由许多等轴较小的α晶粒和少量尺寸较小的β晶粒组成.XRD分析结果表明,当退火温度高于800 ℃时,样品存在Ti3Al杂质相.     

Ti-47．5Al-2．5V-1．0Cr注射成形

以Ti-47.5Al-2.5V-1.0Cr(原子分数,%)气雾化预合金粉末为原料,采用粉末注射成形工艺制备了TiAl合金材料,研究了该TiAl合金脱脂工艺对脱脂坯碳氧残留量和组织的影响规律及烧结工艺对烧结体显微组织、密度和压缩性能的影响规律. 结果表明:在脱脂温度600℃、保温时间为1h和真空脱脂气氛条件下脱除坯体中剩余粘结剂,坯体中残余碳氧含量(质量分数)分别为0.059%和0.12%;脱脂温度从600℃升到1000℃,粉末由枝状组织转变为近γ组织;烧结温度在1410～1450℃,保温时间在1h以内,烧结体可以快速致密化;在1450℃保温30min,烧结体相对密度可以达到95%,烧结体的抗压强度为2105MPa,压缩率达到30.9%,接近铸态合金力学性能;随烧结温度升高,烧结体中的γ相逐渐减少,组织由近片层组织逐渐转变为全片层组织.     

高压热等静压工艺烧结超细WC-10Co复合粉烧结体

实验室采用高压热等静压法（Sintering＋HIP）对超细WC-10Co复合粉烧结体进行烧结实验研究。实验结果表明,在1 360℃的温度下烧结,其抗弯强度较真空预烧前提高19.95%,致密度提高了2%以上,最高达到了97.92%,同时细化了晶粒,提高了合金的机械性能。     

碳氮化钛基金属陶瓷的热等静压处理工艺探讨

采用真空烧结-热等静压处理工艺制备碳氮化钛基金属陶瓷,考察不同热等静压处理温度和时间对材料力学性能及结构的影响.结果表明:热等静压处理可有效消除材料内部孔洞,细化组织;合理的处理温度和时间为1 550℃,30 min;与真空烧结相比,材料的抗弯强度,硬度和致密度均分别提高了22.9%,1.0%和1.2%.     

置氢Ti-6Al-4V合金组织与室温变形行为的相关性

应用压缩实验研究置氢Ti-6Al-4V合金的室温力学行为,采用OM、SEM分析了氢对钛合金组织的影响和断口形貌特征,探讨了置氢钛合金组织和室温变形行为之间的相关性.结果表明:氢的固溶强化作用使置氢Ti-6Al-4V合金硬化效应增加,但适量的氢可以显著降低其压缩屈服强度和弹性模量,且断裂时发生的变形量增加,此时合金组织为á a的双态组织,当合金中产生粗大的a晶粒时,断裂时发生的变形量显著降低;氢的加入促进了合金中斜方马氏体á″的生成;置氢Ti-6Al-4V合金的室温压缩断口为延性沿晶断裂或脆性沿晶断裂和解理型穿晶断裂两种断裂方式的混合断口.     

激光烧结与等静压复合技术制造致密合金零件

通过机械混合Fe,C及环氧树脂粉末配制了选择性激光烧结(SLS)用复合材料,利用SLS方法制备了生坯.分别经过脱脂预烧、冷等静压(CIP)、高温烧结和热等静压(HIP)处理提高其致密度,进而改善其力学性能.并采用阿基米德定律、环境扫描电镜与万能拉伸试验机分别对HIP试样的致密度、微观组织与力学性能进行测试.结果表明:合金材料致密度达到97%左右,极限拉伸强度超过350 MPa,延伸率大于9%,经HIP处理后试样显微组织为粒状珠光体与铁素体.     

Ti-6Al-4V合金电弧熔丝增材的组织性能研究进展

Ti-6Al-4V钛合金具有密度低、高温下组织稳定、强度高的特点,被广泛应用于机翼翼梁、起落架支撑肋等航空工业关键零部件的制造。电弧熔丝增材技术研究始于20世纪80年代,该技术具有成型效率高、原材料利用率高、设备简单等优势。目前,学界对Ti-6Al-4V合金电弧熔丝增材技术开展了广泛研究并已取得一定成果。笔者综述了电弧熔丝增材制造技术的发展历史及研究热点,并整合了国内外Ti-6Al-4V合金电弧熔丝增材技术的最新研究及应用情况,对电弧熔丝增材制造Ti-6Al-4V合金的组织性能特性及调控工艺进行了总结与展望。     

MA-SPS制备超细晶Ti-8Mo-3Fe合金的摩擦磨损性能

以机械合金化+放电等离子烧结(MA-SPS)制备的超细晶Ti-8Mo-3Fe合金为研究对象,研究了合金在模拟体液(SBF)中的摩擦磨损性能,并与放电等离子烧结制备的微米尺寸晶粒的Ti-8Mo-3Fe合金、铸造纯Ti及Ti-6Al-4V(TC4)合金进行了对比.结果表明:采用MA-SPS工艺可制备出高致密度、组织均匀的超细晶Ti-8Mo-3Fe合金,合金由β相及少量α相组成,平均晶粒尺寸为1.5μm,显微硬度为448 HV;在相同摩擦磨损条件下,超细晶Ti-8Mo-3Fe合金的摩损程度明显低于微米晶粒Ti-8Mo-3Fe和铸态的纯Ti及TC4合金,具有最低的磨损体积和较稳定的摩擦系数.超细晶Ti-8Mo-3Fe合金的磨损机制为磨粒磨损,而微米晶粒Ti-8Mo-3Fe和铸态纯Ti及TC4合金的磨损机制为磨粒磨损和黏着磨损并存的混合磨损.     

放电等离子烧结TiAl基合金的显微组织及力学性能

以Ti-47.5Al-2.5V-1.0Cr合金粉末为原料,采用放电等离子烧结工艺制备出TiAl基合金,并研究了制备工艺、显微组织与室温力学性能三者的关系.结果表明,采用放电等离子烧结方法可制备出致密度高、组织均匀的TiAl基合金.烧结温度对合金的显微组织影响显著,且其室温力学性能与显微组织密切相关,显微组织越细小,室温强度和塑性越高.当烧结温度为1100℃时,制备出的TiAl-V-Cr合金显微组织类型为细小双态组织,具有35.2%的压缩率和3321MPa的断裂强度,显示出较好的室温压缩性能.     

热挤压工艺对Ti-6Al-4V钛合金组织与性能的影响

研究了挤压温度和挤压比对Ti-6Al-4V钛合金挤压型材显微组织、织构及力学性能的影响.挤压温度在相变点Tβ以上150～350℃、挤压比λ为25～85范围内时,型材动态再结晶均已完成,形成均匀的魏氏组织.型材的晶粒随挤压温度的降低和挤压比的提高而细化.型材织构在挤压比较低(λ=25)时强度较弱且为随机分布;当挤压比增加时,织构增强并有形成(1219)面纤维织构的趋势;当挤压比提高至85时,形成完整的(1219)面纤维织构.由于织构与晶粒细化的共同作用,使不同挤压条件下得到的Ti-6Al-4V钛合金型材综合力学性能比较稳定,即强度差异均不大于35 MPa,且延伸率和断面收缩率差值均不超过3%.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Jane Eyre——A Feminist In The 19th Century

In the 19th century the society was controlled by men, and women were just appendants of them, they had not any rights and freedom. But Jane was an exception, she showed some characteristics of early feminist. Jane showed her characteristics of feminism in three aspects: rebellion, equality, and independence. These characteristics were helpful to her success, and feminism is the only way out for women of that time.     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~