烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

不同硅饱和系数水榴石的碳酸化分解动力学

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method, which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method. In this study, the effect of the silica saturation coefficient (x) on the carbonation of hydrogarnet was investigated from the kinetic perspective. The results indicated that the carbonation of hydrogarnets with different x values (x = 0.27, 0.36, 0.70, and 0.73) underwent two stages with significantly different rates, and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3. The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol, respectively. Moreover, the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.     

一种超重力燃烧合成制备高性能高熵合金的新方法

A new method of high-gravity combustion synthesis (HGCS) followed by post-treatment (PT) is reported for preparing high-performance high-entropy alloys (HEAs), Cr_0.9FeNi_2.5V_0.2Al_0.5 alloy, whereby cheap thermite powder is used as the raw material. In this process, the HEA melt and the ceramic melt are rapidly formed by a strong exothermic combustion synthesis reaction and completely separated under a high-gravity field. Then, the master alloy is obtained after cooling. Subsequently, the master alloy is sequentially subjected to conventional vacuum arc melting (VAM), homogenization treatment, cold rolling, and annealing treatment to realize a tensile strength, yield strength, and elongation of 1250 MPa, 1075 MPa, and 2.9%, respectively. The present method is increasingly attractive due to its low cost of raw materials and the intermediate product obtained without high-temperature heating. Based on the calculation of phase separation kinetics in the high-temperature melt, it is expected that the final alloys with high performance can be prepared directly across master alloys with higher high-gravity coefficients.     

窄板坯结晶器内连铸工艺参数对钢液流场的影响

Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting (CC) molds with narrow widths for the production of automobile exposed panels. Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process. The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold. Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone. The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min?1 and casting speed of 1.7 m·min?1. Under the present experimental conditions, the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.     

电渣重熔脱硫技术研究进展

Electroslag remelting (ESR) gives a combination of liquid metal refining and solidification structure control. One of the typical aspects of liquid metal refining during ESR for the advanced steel and alloy production is desulfurization. It involves two patterns, i.e., slag–metal reaction and gas–slag reaction (gasifying desulfurization). In this paper, the advances in desulfurization practices of ESR are reviewed. The effects of processing parameters, including the initial sulfur level of consumable electrode, remelting atmosphere, deoxidation schemes of ESR, slag composition, melting rate, and electrical parameters on the desulfurization in ESR are assessed. The interrelation between desulfurization and sulfide inclusion evolution during ESR is discussed, and advancements in the production of sulfur-bearing steel at a high-sulfur level during ESR are described. The remaining challenges for future work are also proposed.     

利用皮秒激光烧蚀制备非球形铝纳米颗粒

We report the picosecond laser ablation of aluminum targets immersed in a polar organic liquid (chloroform, CHCl₃) with ~2 ps laser pulses at an input energy of ~350 μJ. The synthesized aluminum nanoparticles exhibited a surface plasmon resonance peak at ~340 nm. Scanning electron microscopy images of Al nanoparticles demonstrated the spherical morphology with an average size of (27 ± 3.6) nm. The formation of smaller spherical Al nanoparticles and the diminished growth could be from the formation of electric double layers on the Al nanoparticles. In addition to spherical aluminum nanoparticles, triangular/pentagonal/hexagonal nanoparticles were also observed in the colloidal solution. Field emission scanning electron microscopy images of ablated Al targets demonstrated laser induced periodic surface structures (LIPSSs), which were the high spatial frequency LIPSSs (HSF-LIPSSs) since their grating period was ~280 nm. Additionally, coarse structures with a period of ~700 nm were observed.     

《梁山伯与祝英台》与《罗密欧与朱丽叶》调式比较

《梁山伯与祝英台》与《罗密欧与朱丽叶》两部作品的内容都取材于民间故事,都属于标题性音乐作品,作品曲式结构基本相同。不同之处是对造成悲剧原因的展示有着明显区别,主、副部主题的表现和运用截然相反,音乐的主基调有较大差异,作品的整体风格迥异。     

有氧运动与身心健康探析

健康与运动是密不可分的,运动分为有氧和无氧,有氧运动较无氧运动更易普及和被大众接受,从人体长期参加有氧运动对人的身体健康和心理健康的角度来阐述有氧运动对人体的良好影响。     

文献信息情报工作在科技工作及立项决策中的作用

本文揭示了在当今信息市场形势下 ,文献信息情报工作在科技工作和经济立项决策中的作用 ,同时也指出 :图书馆文献信息工作者们能在强手如云的信息市场中占领一块阵地也应成为图书馆界的共识     

道教与魏晋南北朝文人的功利欲望

欲望是作家创作的内驱力,道教对中国古代文人的欲望有什么影响,这是研究中国古代文学和文学理论不能不思考的问题。本文从道教的功利性,文人纷纷走近道教,文学观念中的道教因素等方面,对道教与魏晋南北朝文人的功利欲望作些专门探讨。这无疑会拓展人们研究的新视界。     

博客与高校思想政治教育

网络的发展为我们带来全新便捷的互动平台和交流方式,博客是当今传播文化的重要载体,因个体性、公共性、开放性、成本投入少等特点吸引着"90后"大学生广泛关注。在新形势的要求下,高校辅导员应主动占领网络博客思想政治教育新阵地,加强辅导员博客建设,根据大学生的心理特点,利用博客提升网络思想政治教育工作的吸引力和感染力,创新高校思想政治教育。     

高校管理与师生权益的保护

当前,因高校管理引发的法律纠纷呈上升趋势,究其原因是师生的法治观念在增强,另一方面说明高校在师生管理等方面也存在诸多不适应。要改变这些不适应,就要进行依法治校,更新管理理念。做到规章制度合法、管理行为合法。努力加强法制教育工作和师德校风建设,切实保障师生的合法权益。     

楼兰的兴衰与环境变迁和环境灾害

通过对楼兰兴衰史及同一时期的环境变化的综合研究表明:楼兰的兴衰与环境的变迁、灾变密切相关,自然环境变迁、灾变是楼兰消亡的重要原因     

果蔬加工和进出口环节存在的安全问题及防治对策

我国是果蔬生产大国,近些年果蔬加工业和进出口贸易发展较快.但果蔬加工和进出口环节存在一些安全问题,包括微生物及其毒素超标、加工过程中残留和添加的有害物质、加工过程中产生的有害物质、包装带来的危害.从果蔬原料、加工环节和产品三方面实施标准化,将有利于解决这些问题,促进果蔬产业健康发展.     

荔枝龙眼炭疽病和霜疫霉病的识别与防治

总结了荔枝龙眼重要病害炭疽病和霜疫霉病的症状、病原、发生规律及综合防治措施;指出荔枝龙眼炭疽病和霜疫霉病主要为害叶片、花穗和果实,叶片早落,花穗干枯死亡,果实腐烂并产生异味;两种病害为害造成的损失很大,防治必须及时,且防治措施以农业防治和化学防治为主。     

VB与Excel数据导入导出的研究与实现

通过引用Excel对象实例和ADO对象,解决VB中的数据与Excel数据导入、导出的问题.