烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

含钛高炉炉渣微波合成碳化钛及其介电性能测定

The preparation of functional material titanium carbide by the carbothermal reduction of Ti-bearing blast furnace slag with microwave heating is an effective method for valuable metals recovery; it can alleviate the environmental pressure caused by slag stocking. The dynamic dielectric parameters of Ti-bearing blast furnace slag/pulverized coal mixture under high-temperature heating are measured by the cylindrical resonant cavity perturbation method. Combining the transient dipole and large π bond delocalization polarization phenomena, the interaction mechanism of the microwave macroscopic non-thermal effect on the titanium carbide synthesis reaction was revealed. The material thickness range during microwave heating was optimized by the joint analysis of penetration depth and reflection loss, which is of great significance to the design of the microwave reactor for the carbothermal reduction of Ti-bearing blast furnace slag.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…