Effects of Gd solutes on hardness and yield strength of Mg alloys

Relative contribution of individual strengthening mechanisms to the yield strength of Mg–0–15 wt%Gd alloys were investigated.Alloys with different grain size were prepared by adding Zr and hot extrusion.Hardness and tensile/compression yield strength were tested on the alloys after solid solution treatment and extrusion.HallPetch constants were calculated with hardness and tensile/compressive data.The results showed that the hardness of Mg–Gd alloys with similar Gd content and different grain size were almost the same,which indicates that grain size had little effect on hardness.The hardness linearly increased with rising Gd content(d H_v/dc≈25 kg mm~(-2)/at%Gd).The tensile and compressive yield strengths enhanced with the increase of Gd content for all alloys in different conditions.In addition,the tensile/compressive(t/c)yield asymmetry of extruded alloys decreased with increasing Gd content.Large t/c yield asymmetry ratio(1.77)was observed for pure Mg,and with increasing Gd content this value decreased to 1.With the increasing of tensile strength,the stress intensity factor,k_y,decreased from 0.27 MPa m~(1/2)for Mg–2 wt%Gd alloy to 0.19 MPa m~(1/2) for Mg–5 wt%Gd alloy,then increased to 0.29 MPa m~(1/2) for Mg–15 wt%Gd alloy.However,k_yincreased linearly form 0.16–0.31 MPa for compression test.The influence of grain size strengthening was eliminated,and the yield strength of tension and compression both linearly increased with c~n,where c is the atom concentration of Gd,and n=1/2 or 2/3.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of Zn addition on microstructure and mechanical properties of an Al–Mg–Si alloy

In the present work, an Al–0.66Mg–0.85Si–0.2Cu alloy with Zn addition was investigated by electron back scattering diffraction(EBSD), high resolution electron microscopy(HREM), tensile and Erichsen tests. The mechanical properties of the alloy after pre-aging met the standards of sheet forming. After paint baking, the yield strength of the alloy was improved apparently. GP(Ⅱ) zones and η’phases were formed during aging process due to Zn addition. With the precipitation of GP zones, β″ phases, GP(Ⅱ) zones and η’phases, the alloys displayed excellent mechanical properties.     

Microstructure,mechanical, and corrosion properties of extruded low-alloyed Mg–xZn–0.2Ca alloys

The microstructure, mechanical, and corrosion properties of extruded low-alloyed Mg-xZn-0.2Ca (x=0, 1.0, 2.0, 3.0) alloys were investigated in this study. Findings from scanning electron microscope, X-ray diffraction and transmission electron microscopy results indicate that the amount of ternary Ca₂Mg₆Zn₃ phase, as the only secondary phase in 1.0Zn, 2.0Zn, and 3.0Zn alloys, gradually increases with the addition of Zn, while the Mg₂Ca phase was observed in the Mg-0.2Ca alloy only. Zn has a strong effect on the orientation and intensity of textures, which also influence mechanical behaviors, as revealed by electron back-scatter diffraction. Among all the alloys, the Mg-2.0Zn-0.2Ca alloy obtains the maximum tensile strength (278 MPa) and yield strength (230 MPa). Moreover, Zn addition has an evident influence on the corrosion properties of Mg-xZn-0.2Ca alloy, and Mg-1.0Zn-0.2Ca alloy exhibits the minimum corrosion rate. This paper provides a novel low-alloyed magnesium alloy as a potential biodegradable material.     

Corrosion behavior of Mg–Y alloy in NaCl aqueous solution

The corrosion behavior of Mg–(0.25, 2.5, 5, 8 and 15)Y alloys in 3.5wt.% NaCl aqueous solution was investigated. It was found that the degree of corrosion deterioration increased with increasing immersion time up to 2 h. Corrosion modes for the alloys with low and high content of Y element were general corrosion and pitting corrosion, respective ly, and the threshold content for the corrosion mode change was 2.5% for the tested alloys. The experimental results showed that the addition of Y refined the grain of the alloy, and the distribution, i.e., continuous or not, of the Mg24Y5 phases had great effect on the corrosion rate and corrosion mode.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Effect of thermo-mechanical treatment on mechanical and elastic properties of Ti–36Nb–5Zr alloy

The evolutions of phase constitutions and mechanical properties of a β-phase Ti–36Nb–5Zr(wt%) alloy during thermo-mechanical treatment were investigated. The alloy consisted of dual(β t α″) phase and exhibited a double yielding phenomenon in solution treated state. After cold rolling and subsequent annealing at 698 K for 20 min, an excellent combination of high strength(833 MPa) and low modulus(46 GPa) was obtained. The high strength can be attributed to high density of dislocations, nanosized α phase and grain refinement. On the other hand, the low Young's modulus originates from the suppression of chemical stabilization of β phase during annealing, which guarantees the low β-phase stability. Furthermore, the single-crystal elastic constants of the annealed Ti–36Nb–5Zr alloy were extracted from polycrystalline alloy using an in-situ synchrotron X-ray technique. The results indicated that the low shear modulus C44 contributes to the low Young's modulus for the Ti–36Nb–5Zr alloy, suggesting that reducing C44 through thermo-mechanical treatment might be an efficient approach to realize low Young's modulus in β-phase Ti alloys. The results achieved in this study could be helpful to elucidate the origin of low modulus and sheds light on developing novel biomedical Ti alloys with both low modulus and high strength.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

DSC analyses of static and dynamic precipitation of an Al–Mg–Si–Cu aluminum alloy

In the present investigation, both static and dynamic precipitations of an Al–Mg–Si–Cu aluminum alloy after solid-solution treatment(SST)were comparatively analyzed using differential scanning calorimetry(DSC). Dynamic aging was performed in the SST alloy through equal channel angular pressing(ECAP) at different temperatures of room temperature, 110, 170, 191 and 300 1C. For comparison, static artificial aging was conducted in the SST alloy at 191 1C with two aging times of 4 and 10 h. The DSC analyses reveal that the dynamic precipitation has occurred in the ECAPed samples, while the activation energies associated with the strengthening precipitates in the dynamic samples are considerably higher than the energies in the SST and static aged samples. The higher activation energies are probably attributed to the smaller grains and higher dislocation density developed after ECAP. The results in the present investigation allow the prediction of the type of the dynamic precipitates to influence the strength of the ultrafine grained alloy during ECAP at various temperatures.     

Microstructure and mechanical properties of the micrograined hypoeutectic Zn–Mg alloy

A biodegradable Zn alloy, Zn–1.6Mg, with the potential medical applications as a promising coating material for steel components was studied in this work. The alloy was prepared by three different procedures: gravity casting, hot extrusion, and a combination of rapid solidification and hot extrusion. The samples prepared were characterized by light microscopy, scanning electron microscopy, transmission electron microscopy, and X-ray diffraction analysis. Vickers hardness, tensile, and compressive tests were performed to determine the samples’ mechanical properties. Structural examination reveals that the average grain sizes of samples prepared by gravity casting, hot extrusion, and rapid solidification followed by hot extrusion are 35.0, 9.7, and 2.1 μm, respectively. The micrograined sample with the finest grain size exhibits the highest hardness (Hv = 122 MPa), compressive yield strength (382 MPa), tensile yield strength (332 MPa), ultimate tensile strength (370 MPa), and elongation (9%). This sample also demonstrates the lowest work hardening in tension and temporary softening in compression among the prepared samples. The mechanical behavior of the samples is discussed in relation to the structural characteristics, Hall–Petch relationship, and deformation mechanisms in fine-grained hexagonal-close-packed metals.     

Development of NiTiNb in-situ composite with high damping capacity and high yield strength

The shape memory alloys are well known to exhibit high damping capacity in martensite state, but possess low yield strength because of the reorientation or de -twining of the martensite variants. The high damping mechanism of shape memory alloys was introduced. The NiTiNb alloys with high yield strength and high damping capacity were designed and prepared. The microstructure evolution, martensitic transformation behavior, damping capacity and mechanical properties of series NiTiNb alloys were investigated. In view of the microstructure characteristic s of the NiTiNb in-situ composites, the mechanism associated with high damping capacity and high yield strength was discussed. The results show that NiTiNb alloys feature in in-situ composite, compo sed of primary NiTi(Nb) phase and fine lamellar eutectics of NiTi(Nb) and β-Nb.     

Development of NiTiNb in-situ composite with high damping capacity and high yield strength

The shape memory alloys are well known to exhibit high damping capacity in martensite state,but possess low yield strength because of the reorientation or de-twining of the martensite variants.The high damping mechanism of shape memory alloys was introduced.The NiTiNb alloys with high yield strength and high damping capacity were designed and prepared.The microstructure evolution,martensitic transformation behavior,damping capacity and mechanical properties of series NiTiNb alloys were investigated.In vi...     

Effect of homogenization process on the hardness of Zn–Al–Cu alloys

The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell “B” hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of the θ and τ' phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and temperature, used in their preparation.     

A β-type TiNbZr alloy with low modulus and high strength for biomedical applications

The effect of thermo-mechanical treatment on the mechanical properties of a novel β-type Ti–36Nb–5Zr(wt%) alloy has been investigated.The solution treated alloy consists of β and α″ phases and exhibits a two-stage yielding with a low yield stress(around 100 MPa). After cold rolling at a reduction of 87.5% and subsequent annealing treatment at 698 K for 25 min, a fine microstructure with nanosized α precipitates distributed in small β grains as well as high density of dislocations was obtained to achieve a yield strength of 720 MPa and a ultimate tensile strength of 860 MPa. In spite of the formation of α precipitates, the β-stabilizers are not enriched in the parent β matrix due to the short duration and low temperature of the thermal treatment, resulting in a low chemical stability of β phase. The low stability of β phase and the small volume fraction of α precipitates produce a low Young’s modulus of 48 GPa. Such an excellent combination of low elastic modulus and high strength in mechanical properties indicates great potential for biomedical applications.     

Effects of P addition on the microstructure and mechanical properties of Mg–5%Sn–1.25%Si alloy

The effects of Al-P addition on the microstructure and mechanical properties of as-cast Mg–5%Sn–1.25%Si magnesium alloy were investigated. The results show that the phases of the as-cast alloy are composed of α-Mg, Mg2 Sn, Mg2 Si, little P, and AlP. The Chinese character shape Mg2 Si phase changes into a granular morphology by P addition because AlP can act as a heterogeneous nucleation core for the Mg2 Si phase. When 0.225wt% of Al–3.5%P alloy is added, the mechanical properties of the Mg–5%Sn–1.25%Si alloy are greatly improved, and the tensile strength increases from 156 to 191 MPa, an increase of 22.4% compared to the alloy without P addition. When the amount of Al–3.5%P reaches 0.300wt%, a segregation phenomenon occurs in the granular Mg2 Si phase, and the tensile strength and hardness decrease though the elongation increases.     

Microstructure s and mechanical properties of Ti3Al/Ni-based superalloy joints arc welded with Ti –Nb and Ti– Ni – Nb filler alloys

Dissimilar joining of Ti3Al-based alloy to Ni-based superalloy has been carried out using gas tungsten arc(GTA) welding technology with Ti–Nb and Ti–Ni–Nb filler alloys.The joint welded with the Ti–Nb filler alloy contained much less interfacial brittle phases than the one using the Ti–Ni–Nb filler alloy.The average room-temperature tensile strength of the joint welded with Ti–Nb was 202 MPa and the strength value of the one welded with Ti–Ni–Nb was 128 MPa.For both fillers,the weak links of the dissimilar joints were the weld/In718 interfaces.The presence of TiNi,TiNi3 and Ni3Nb intermetallic compounds in the joint welded with Ti–Ni–Nb induced microcracks at the weld/In718 interface and deteriorated the mechanical properties of the joint.And the adoption of the Ti–Nb filler alloy decreased the formation tendency of interfacial brittle phases to some extent and thus enhanced the tensile strength of the joint.     

Growth and properties of semi-organic nonlinear optical crystal: L-Glutamic acid hydrochloride

Semiorganic nonlinear optical crystal of L-Glutamic acid hydrochloride(LGHC) was grown from aqueous solution by slow evaporation technique. Single crystal X-ray Diffraction analysis confirms that LGHC crystallizes in orthorhombic system with noncentrosymmetric space group P2_12_12_1. The powder X-ray diffraction study confirms the crystallinity of the grown crystal. The fundamental functional groups of the grown crystals were analyzed by Fourier Transform Infrared spectroscopic analysis in the range of 450–4000 cm~(-1). The range of optical transmission was ascertained using UV–vis–NIR studies. The Refractive Index of the LGHC crystal was found to be 1.4. The second harmonic generation efficiency of the LGHC was determined using Kurtz and Perry powder technique and it was 0.5 times greater than that of the KDP crystal. Thermo Gravimetric Analysis(TGA) and Differential Thermal Analysis(DTA) were used to study thermal behavior of the sample. The dielectric behavior and ac conductivity of the sample were studied as a function of frequency for different temperatures. The mechanical strength of the crystal was determined by Vicker's Hardness test. The elastic stiffness constant and yield strength of the sample was calculated.     

Microstructure,phase stability and mechanical properties of Nb–Ni–Ti–Co–Zr and Nb–Ni–Ti–Co–Zr–Hf high entropy alloys

Owning to their excellent thermal stability and high strength at elevated temperature,high entropy alloys(HEAs) possess great potential for the application in aviation and aerospace fields.In present work,two novel Nb-Ni-Ti-Co-Zr and Nb-Ni-Ti-Co-Zr-Hf HEAs were prepared by arc melting and copper mold suction-casting method.The microstructure,phase stability,mechanical properties at room temperature and elevated temperature of the two HEAs were studied.Both of the HEAs possess high yield stress at room temperature,especially for the Nb-Ni-Ti-Co-Zr(with 2331 Mpa).In addition,the Nb-Ni-Ti-Co-Zr HEA exhibited high yield stress of 564 Mpa at elevated temperature of 800 ℃ and large compressive plastic strain(more than 50%at 800 ℃).Nb-Ni-Ti-Co-Zr-Hf alloy showed new phase precipitation at 800 ℃,whereas the structure of Nb-Ni-Ti-Co-Zr was more stable,which is one of the reason why it possesses high strength at room temperature and elevated temperature.The high temperature properties of the Nb-Ni-Ti-Co-Zr HEA make it promising for high temperature application.     

Structure and corrosion resistance of Al–Cu–Fe alloys

The microstructure and electrochemical properties of Al–Cu–Fe alloys with the atomic compositions of Al_(65)Cu_(20)Fe_(15),Al_(78)Cu_7Fe_(15)and Al_(80)Cu_5Fe_(14)Si_1have been studied.The alloys were produced by induction melting of pure elements with copper mold casting.The microstructure of the alloys was analyzed by X-ray diffraction and high-resolution transmission electron microscopy.The formation of quasicrystalline phases in the Al–Cu–Fe alloys was confirmed.The presence of intermetallic phases was observed in the alloys after crystallization in a form of ingots and plates.The electrochemical measurements were conducted in 3.5%NaCl solution.The electronic structure of the alloys was determined by X-ray photoelectron spectroscopy.The post corrosion surface of the samples was checked using a scanning electron microscope equipped with the energydispersive X-ray detector.It was observed that the Al_(65)Cu_(20)Fe_(15)alloy had the highest corrosion resistance.The improved corrosion resistance parameters were noted for the plate samples rather than those in the as-cast state.And the hardness of the Al_(65)Cu_(20)Fe_(15)alloy was significantly higher than the other alloy samples.