A β-type TiNbZr alloy with low modulus and high strength for biomedical applications

The effect of thermo-mechanical treatment on the mechanical properties of a novel β-type Ti–36Nb–5Zr(wt%) alloy has been investigated.The solution treated alloy consists of β and α″ phases and exhibits a two-stage yielding with a low yield stress(around 100 MPa). After cold rolling at a reduction of 87.5% and subsequent annealing treatment at 698 K for 25 min, a fine microstructure with nanosized α precipitates distributed in small β grains as well as high density of dislocations was obtained to achieve a yield strength of 720 MPa and a ultimate tensile strength of 860 MPa. In spite of the formation of α precipitates, the β-stabilizers are not enriched in the parent β matrix due to the short duration and low temperature of the thermal treatment, resulting in a low chemical stability of β phase. The low stability of β phase and the small volume fraction of α precipitates produce a low Young’s modulus of 48 GPa. Such an excellent combination of low elastic modulus and high strength in mechanical properties indicates great potential for biomedical applications.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

A Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous filler metal for improving the strength of Ti–6Al–4V alloy brazing joint

Ti_(50)Zr_(27)Cu_8Ni_4Co_3Fe_2Al_3Sn_3(at%) amorphous filler metal with low Cu and Ni contents in a melt-spun ribbon form was developed for improving mechanical properties of Ti–6Al–4V alloy brazing joint through decreasing brittle intermetallics in the braze zone. Investigation on the crystallization behavior of the multicomponent Ti–Zr–Cu–Ni–Co–Fe–Al–Sn amorphous alloy indicates the high stability of the supercooled liquid against crystallization that favors the formation of amorphous structure. The Ti–6Al–4V joint brazed with this Ti-based amorphous filler metal with low total content of Cu and Ni at 1203K for 900s mainly consists of α-Ti, β-Ti,minor Ti–Zr-rich phase and only a small amount of Ti_3Cu intermetallics, leading to the high shear strength of the joint of about 460 MPa. Multicomponent composition design of amorphous alloys is an effective way of tailoring filler metals for improving the joint strength.     

α′ Type Ti– Nb– Zr alloys with ultra-low Young''s modulus and high strength

a’ phase based Ti-Nb-Zr alloys with low Young’s modulus and high strength were prepared,and their microstructure and mechanical properties were characterized.It was revealed that the lattice expansion by Nb and Zr addition as well as the presence of a few of a" martensite might be responsible for the low modulus achieved.Ti-15Nb-9Zr alloy,with ultralow modulus of 39 GPa and high strength of850 MPa,could be a potential candidate for biomedical applications.     

Microstructural evolution and mechanical behavior of metastable β-type Ti–30Nb–1Mo–4Sn alloy with low modulus and high strength

A metastable P-type Ti-30Nb-lMo-4Sn alloy with ultralow elastic modulus and high strength was fabricated.Under the solution treatment state,the Ti-30Nb-1Mo-4Sn alloy possesses low yield strength of about 130 MPa owing to the presence of the coarse α " martensitic laths.Upon a cold rolling and annealing process,the martensitic transformation from β to α" is significantly retarded due to the inhibitory effect of grain boundaries and dislocations.As a result,the metastable β phase with low total amount of β-stabilizers is retained to room temperature,giving rise to a low modulus of 45 GPa.Meanwhile,nano-sized a precipitates and dislocation tangles play a key role in strengthening the Ti-30Nb-1Mo-4Sn alloy,resulting in a high tensile strength of ~ 1000 MPa.With low elastic modulus and high strength,the metastable P-type Ti-30Nb-1Mo-4Sn alloy could be a potential candidate for biomedical materials.     

Peculiar aging response of near b Ti–25 Nb–2Mo–4Sn alloy for biomedical applications

In this paper,aging response of a recently developed near β Ti-25Nb-2Mo-4Sn(wt%) alloy with high strength and low modulus was investigated intensively.The experimental results from X-ray diffraction and transmission electron microscopy showed that the aging production of the Ti-2524 alloy was(β+ω) or(β+α) even under the same aging treatment condition,depending on the pre-treatments prior to the aging.Solid evidence confirmed the competition between stable α phase and metastable ω phase during the decomposition of β phase on aging.Different aging response of Ti-2524 alloy can be attributed to high-density dislocations and grain boundaries which suppress the formation of ω,and alternatively promote a phase formation.This provides a thermo-mechanical approach to inhibit deleterious ω phase formation and assist fine α phase precipitation.Upon an appropriate aging treatment,superior mechanical properties of high ultimate tensile strength(1233 MPa) and low elastic modulus(77 GPa) were achieved in Ti-2524 alloy.     

Microstructure and properties of Cu–Ti–Ni alloys

The effects of Ni addition and aging treatments on the microstructure and properties of a Cu–3Ti alloy were investigated. The microstructure and precipitation phases were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy; the hardness, electrical conductivity, and elastic modulus of the resulting alloys were also tested. The results show that Ni addition increases the electrical conductivity and elastic modulus, but decreases the hardness of the aged Cu–3Ti alloy. Within the range of the experimentally investigated parameters, the optimal two-stage aging treatment for the Cu–3Ti–1Ni and Cu–3Ti–5Ni alloy was 300°C for 2 h and 450°C for 7 h. The hardness, electrical conductivity, and elastic modulus of the Cu–3Ti–1Ni alloy were HV 205, 18.2% IACS, and 146 GPa, respectively, whereas the hardness, electrical conductivity, and elastic modulus of the Cu–3Ti–5Ni alloy were HV 187, 31.32% IACS, and 147 GPa, respectively. Microstructural analyses revealed that β′-Ni3 Ti and β′-Cu4 Ti precipitate from the Cu matrix during aging of the Cu–3Ti–5Ni alloy and that some residual Ni Ti phase remains. The increased electrical conductivity is ascribed to the formation of Ni Ti, β′-Ni3 Ti, and β′-Cu4 Ti phases.     

Microstructure evolution and mechanical properties of Ti-8Nb-2Fe-0.2O alloy with high elastic admissible strain for orthopedic implant applications

A Ti-8Nb-2Fe-0.2O(wt.%) alloy with high strength,high elastic admissible strain(δ) and low cost was designed using d-electron theory combined with electron-to-atom ratio(e/a) approach.Interstitial oxygen was introduced to strengthen the matrix of the alloy.The β-solution treated alloy was mainly composed of α " martensite with internal {111}_(α") type Ⅰ nano-twins.The α " martensite with hexagonal-like crystal structure caused by interstitial oxygen showed a high strength of 1.1 GPa but limited ductility.The alloy generated equiaxed fine-grained a phase embedded by β matrix via hot rolling and subsequent annealing in α+β phase field.The obtained alloy indicated a good combination of mechanical properties with ultimate tensile strength,Young's modulus,ductility and δ value of 1029 MPa,74 GPa,21% tensile elongation and 1.32%,respectively.These findings demonstrate that interstitial oxygen and martensitic nano-twins can be used to strengthen the soft α" martensite and high elastic admissible strain can be obtained by formation of equiaxed fine-grained α phase embedded by βmatrix in this Ti-8Nb-2Fe-0.2O alloy for orthopedic implant.     

High plastic Zr–Cu–Fe–Al–Nb bulk metallic glasses for biomedical applications

Four Zr–Cu–Fe–Al-based bulk metallic glasses(BMGs) with Zr contents greater than 65at% and minor additions of Nb were designed and prepared. The glass forming abilities, thermal stabilities, mechanical properties, and corrosion resistance properties of the prepared BMGs were investigated. These BMGs exhibit moderate glass forming abilities along with superior fracture and yield strengths compared to previously reported Zr–Cu–Fe–Al BMGs. Specifically, the addition of Nb into this quaternary system remarkably increases the plastic strain to 27.5%, which is related to the high Poisson's ratio and low Young's and shear moduli. The Nb-bearing BMGs also exhibit a lower corrosion current density by about one order of magnitude and a wider passive region than 316 L steel in phosphate buffer solution(PBS, pH 7.4). The combination of the optimized composition with high deformation ability, low Young's modulus, and excellent corrosion resistance properties indicates that this kind of BMG is promising for biomedical applications.     

Effects of alloying and high-temperature heat treatment on the microstructure of Nb–Ti–Si based ultrahigh temperatur e alloys

The phase co mpositions, microstructure and especi ally phase i nterfaces in the as-cast and heat-treated Nb– Ti–Si based ultrahigh temperature alloys have been investigated. It is shown that β(Nb,X)5Si3 and γ(Nb,X)5Si3 are the primary p hase s in the Nb–22Ti–16Si–5Cr–5Al (S1) (at%) and Nb–20Ti–16Si–6C r–4Al–5Hf–2B–0.06Y (S2) (at% ) alloys, respectively. The Nb solid solution (Nbss) is the primary phase in Nb–22Ti–14Si–5Hf–3Al–1. 5B –0.0 6Y (S3) (at%) alloy . An orientation relationship between Nbss and γ(Nb,X)5Si3 was determine d to be (1-10)Nb//(101-0)γ and [111]Nb//[0001]γ in the as-cast S2 and S3 alloys. Some original β(Nb,X)5Si3 transfor med into α(Nb,X)5Si3 because Al and Cr diffused from the β(Nb,X)5Si3 to Nbss during heattreatment at 1500 °C for 50 h in the S1 alloy. Mean while, Ti diffused from Nbss to β(Nb,X)5Si3, which induced a Ti to generate near the interface between Nbss and Ti-rich β(Nb,X)5Si3. The orientation relationship between the newl y-formed a Ti and previous Nbss was (110 )Nb//(1-10-1) αTi and [001]Nb//(12-3-1)αTi. Among the ( Nb,X)5Si3 phases , the contents o f Cr and Al in β(Nb,X)5Si3 are n earl y the same as those in γ(Nb,X)5Si3 but obviously hi gher than those in the α(Nb,X)5Si3, where as the content of Si in α(Nb,X)5Si3 is nearly the same a s that in γ(Nb,X)5Si3 but higher than that in the β(Nb,X)5Si3     

Microstructure s and mechanical properties of Ti3Al/Ni-based superalloy joints arc welded with Ti –Nb and Ti– Ni – Nb filler alloys

Dissimilar joining of Ti3Al-based alloy to Ni-based superalloy has been carried out using gas tungsten arc(GTA) welding technology with Ti–Nb and Ti–Ni–Nb filler alloys.The joint welded with the Ti–Nb filler alloy contained much less interfacial brittle phases than the one using the Ti–Ni–Nb filler alloy.The average room-temperature tensile strength of the joint welded with Ti–Nb was 202 MPa and the strength value of the one welded with Ti–Ni–Nb was 128 MPa.For both fillers,the weak links of the dissimilar joints were the weld/In718 interfaces.The presence of TiNi,TiNi3 and Ni3Nb intermetallic compounds in the joint welded with Ti–Ni–Nb induced microcracks at the weld/In718 interface and deteriorated the mechanical properties of the joint.And the adoption of the Ti–Nb filler alloy decreased the formation tendency of interfacial brittle phases to some extent and thus enhanced the tensile strength of the joint.     

Microstruct ural evolution and mechanical behavior of metastable β -type Ti – 25Nb–2Mo – 4Sn alloy with high strength and low modulus

This paper presents a systematic study of newly developed metastable β-type Ti-25Nb-2Mo-4Sn (wt%) alloy with high strength and low elastic modulus, with focus on the microstructural evolution and mechanical behavior associated with aging. The pre-treatment (solution treatment or cold rolling) prior to aging exerts substantial influence on the subsequent aging response including microstructural evolution and mechanical behavior. Even under the same aging treatment, the aging products could be (β+ω), or alternatively (β+α), depending on the pre-treatments. This interesting aging response was discussed on the basis of the mechanism for ω formation. High-density dislocation tangles and grain boundaries induced by severe cold rolling play a key role in hindering the transition from β to isothermal ω, favoring the precipitation of α phase on aging. By aging cold-rolled specimen for short time, superior mechanical properties, i.e. high ultimate strength of ～1113 MPa and low elastic modulus of ～65 GPa, achieved in Ti-25Nb-2Mo-4Sn alloy. The characterization of microstructural evolution and compositional change indicated that the precipitation of fine α does not cause the enrichment of β-stabilizers in β matrix upon a short-time aging, guaranteeing low elastic modulus of the short-time aged specimen. Meanwhile, fine α precipitates as well as dislocations play a crucial part in strengthening, giving rise to its high yield strength and high ultimate tensile strength.     

Microstructure evolution and mechanical properties of a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy after a lower-temperature homogenization treatment

In this paper,a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy with a diameter of 600 mm was successfully prepared by the semi-continuous casting method.The alloy was subsequently annealed at a relatively low temperature of 430°C for 12 h as a homogenization treatment.The microstructure and room-temperature mechanical properties of the alloy were investigated systematically.The results show that the as-cast alloy contained a mass of discontinuous lamellar-shaped 18 R long-period stacking ordered(LPSO) phases with a composition of Mg10 Zn Y and an α-Mg matrix,along with net-shaped Mg5(Y,Gd) eutectic compounds at the grain boundaries.Most of the eutectic compounds dissolved after the homogenization treatment.Moreover,the amount and dimensions of the lamellar-shaped LPSO phase obviously increased after the homogenization treatment.The structure of the phase transformed into 14H-type LPSO with composition Mg12Zn(Y,Gd).The mechanical properties of the heat-treated large-sized alloy ingot are uniform.The ultimate tensile strength(UTS) and tensile yield strength(TYS) of the alloy reached 207.2 MPa and 134.8 MPa,respectively,and the elongation was 3.4%.The high performances of the large-sized alloy ingot after the homogenization treatment is attributed to the strengthening of the α-Mg solid solution and to the plentiful LPSO phase distributed over the α-Mg matrix.     

Effect of Zn addition on microstructure and mechanical properties of an Al–Mg–Si alloy

In the present work, an Al–0.66Mg–0.85Si–0.2Cu alloy with Zn addition was investigated by electron back scattering diffraction(EBSD), high resolution electron microscopy(HREM), tensile and Erichsen tests. The mechanical properties of the alloy after pre-aging met the standards of sheet forming. After paint baking, the yield strength of the alloy was improved apparently. GP(Ⅱ) zones and η’phases were formed during aging process due to Zn addition. With the precipitation of GP zones, β″ phases, GP(Ⅱ) zones and η’phases, the alloys displayed excellent mechanical properties.     

Development of NiTiNb in-situ composite with high damping capacity and high yield strength

The shape memory alloys are well known to exhibit high damping capacity in martensite state, but possess low yield strength because of the reorientation or de -twining of the martensite variants. The high damping mechanism of shape memory alloys was introduced. The NiTiNb alloys with high yield strength and high damping capacity were designed and prepared. The microstructure evolution, martensitic transformation behavior, damping capacity and mechanical properties of series NiTiNb alloys were investigated. In view of the microstructure characteristic s of the NiTiNb in-situ composites, the mechanism associated with high damping capacity and high yield strength was discussed. The results show that NiTiNb alloys feature in in-situ composite, compo sed of primary NiTi(Nb) phase and fine lamellar eutectics of NiTi(Nb) and β-Nb.     

Microstructure and properties of a wear resistant Al–25Si–4Cu–1Mg coating prepared by supersonic plasma spraying

A high content silicon aluminum alloy(Al–25Si–4 Cu–1Mg) coating was prepared on a 2A12 aluminum alloy by supersonic plasma spraying. The morphology and microstructure of the coating were observed and analyzed. The hardness, elastic modulus, and bonding strength of the coating were measured. The wear resistance of the coating and 2A12 aluminum alloy was studied by friction and wear test. The results indicated that the coating was compact and the porosity was only 1.5%. The phase of the coating was mainly composed of α-Al and β-Si as well as some hard particles(Al_9Si,Al_(3.21)Si_(0.47), and CuAl_2). The average microhardness of the coating was HV 242, which was greater than that of 2 A12 aluminum alloy(HV 110). The wear resistance of the coating was superior to 2A12 aluminum alloy. The wear mechanism of the 2A12 aluminum alloy was primarily adhesive wear, while that of the coating was primarily abrasive wear. Therefore, it is possible to prepare a high content silicon aluminum alloy coating with good wear resistance on an aluminum alloy by supersonic plasma spraying.     

Microstructural evolution in Al–Zn–Mg–Cu–Sc–Zr alloys during short-time homogenization

Microstructural evolution in a new kind of aluminum(Al) alloy with the chemical composition of Al–8.82Zn–2.08Mg– 0.80Cu–0.31Sc–0.3Zr was investigated. It is found that the secondary phase Mg Zn2 is completely dissolved into the matrix during a short homogenization treatment(470°C, 1 h), while the primary phase Al3(Sc,Zr) remains stable. This is due to Sc and Zr additions into the Al alloy, high Zn/Mg mass ratio, and low Cu content. The experimental findings fit well with the results calculated by the homogenization diffusion kinetics equation. The alloy shows an excellent mechanical performance after the short homogenization process followed by hot-extrusion and T6 treatment. Consequently, a good combination of low energy consumption and favorable mechanical properties is obtained.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

Saturation phenomenon of Ce and Ti in the modification of Al–Zn–Si filler metal

Cerium and titanium were added to an Al–42Zn–6.5Si brazing alloy, and the subsequent microstructures of the brazing alloy and the 6061 Al alloy brazing seam were investigated. The microstructures of filler metals and brazed joints were characterized by scanning electron microscopy and X-ray energy dispersion spectrometry. A new Ce–Ti phase formed around the silicon phase in the modified filler metal and this saturation phenomenon was analyzed. Interestingly, following brazing of the 6061 alloy, there is no evidence of the Ce–Ti phase in the brazing seam. Because of the mutual solubility of the brazing alloy and base metal, the quantity of the solvent increases, and the solute Ce and Ti atoms assume an undersaturated state.