Microstructure,mechanical, and corrosion properties of extruded low-alloyed Mg–xZn–0.2Ca alloys

The microstructure, mechanical, and corrosion properties of extruded low-alloyed Mg-xZn-0.2Ca (x=0, 1.0, 2.0, 3.0) alloys were investigated in this study. Findings from scanning electron microscope, X-ray diffraction and transmission electron microscopy results indicate that the amount of ternary Ca₂Mg₆Zn₃ phase, as the only secondary phase in 1.0Zn, 2.0Zn, and 3.0Zn alloys, gradually increases with the addition of Zn, while the Mg₂Ca phase was observed in the Mg-0.2Ca alloy only. Zn has a strong effect on the orientation and intensity of textures, which also influence mechanical behaviors, as revealed by electron back-scatter diffraction. Among all the alloys, the Mg-2.0Zn-0.2Ca alloy obtains the maximum tensile strength (278 MPa) and yield strength (230 MPa). Moreover, Zn addition has an evident influence on the corrosion properties of Mg-xZn-0.2Ca alloy, and Mg-1.0Zn-0.2Ca alloy exhibits the minimum corrosion rate. This paper provides a novel low-alloyed magnesium alloy as a potential biodegradable material.     

Microstructure evolution and mechanical properties of a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy after a lower-temperature homogenization treatment

In this paper,a large-sized ingot of Mg–9Gd–3Y–1.5Zn–0.5Zr(wt%) alloy with a diameter of 600 mm was successfully prepared by the semi-continuous casting method.The alloy was subsequently annealed at a relatively low temperature of 430°C for 12 h as a homogenization treatment.The microstructure and room-temperature mechanical properties of the alloy were investigated systematically.The results show that the as-cast alloy contained a mass of discontinuous lamellar-shaped 18 R long-period stacking ordered(LPSO) phases with a composition of Mg10 Zn Y and an α-Mg matrix,along with net-shaped Mg5(Y,Gd) eutectic compounds at the grain boundaries.Most of the eutectic compounds dissolved after the homogenization treatment.Moreover,the amount and dimensions of the lamellar-shaped LPSO phase obviously increased after the homogenization treatment.The structure of the phase transformed into 14H-type LPSO with composition Mg12Zn(Y,Gd).The mechanical properties of the heat-treated large-sized alloy ingot are uniform.The ultimate tensile strength(UTS) and tensile yield strength(TYS) of the alloy reached 207.2 MPa and 134.8 MPa,respectively,and the elongation was 3.4%.The high performances of the large-sized alloy ingot after the homogenization treatment is attributed to the strengthening of the α-Mg solid solution and to the plentiful LPSO phase distributed over the α-Mg matrix.     

Effects of Sn addition on microstructure and mechanical properties of Mg- Zn-Al alloys

The effects of Sn addition(0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in cast and extruded states were investigated, and the mechanical properties of as-extruded Mg-4Zn-1.5Al-xSn studied. The experimental results showed that the as-cast Mg-4Zn-1.5Al alloy was composed of two phases α-Mg and Mg_(32)(Al, Zn)_(49), while Sn-containing alloys consisted of α-Mg, Mg_(32)(Al, Zn)_(49) and Mg_2Sn phases, and Mg_(32)(Al, Zn)_(49) was not detected after extruding due to that the most of them dissolved into the matrix during the homogenized treatment. The addition of Sn refined the grains of as-cast and as-extruded Mg-Zn-Al alloys obviously. It was noted that the basal texture intensity reduced with increasing Sn content significantly in as-extruded Mg-Zn-Al alloys. The tensile tests results indicated that Sn addition improve the tensile strength of the extruded alloys,while it had a harmful effect on the ductility. When the addition of Sn was 2 wt%, the ultimate tensile strength(UTS), yield strength(YS) and elongation(ε_f) of the alloy were 280 MPa, 147 MPa and 17.4%, respectively.     

Effects of P addition on the microstructure and mechanical properties of Mg–5%Sn–1.25%Si alloy

The effects of Al-P addition on the microstructure and mechanical properties of as-cast Mg–5%Sn–1.25%Si magnesium alloy were investigated. The results show that the phases of the as-cast alloy are composed of α-Mg, Mg2 Sn, Mg2 Si, little P, and AlP. The Chinese character shape Mg2 Si phase changes into a granular morphology by P addition because AlP can act as a heterogeneous nucleation core for the Mg2 Si phase. When 0.225wt% of Al–3.5%P alloy is added, the mechanical properties of the Mg–5%Sn–1.25%Si alloy are greatly improved, and the tensile strength increases from 156 to 191 MPa, an increase of 22.4% compared to the alloy without P addition. When the amount of Al–3.5%P reaches 0.300wt%, a segregation phenomenon occurs in the granular Mg2 Si phase, and the tensile strength and hardness decrease though the elongation increases.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

High thermal conductivity and high strength magnesium alloy for high pressure die casting ultrathin-walled components

With the rapid development of 3C industries,the demand for high-thermal-conductivity magnesium alloys with high mechanical performance is increasing quickly.However,the thermal conductivities of most common Mg foundry alloys(such as Mg-9wt%-1wt%Zn)are still relatively low.In this study,we developed a high-thermal-conductivity Mg-4Al-4Zn-4RE-1Ca(wt%,AZEX4441)alloy with good mechanical properties for ultrathin-walled cellphone components via high-pressure die casting(HPDC).The HPDC AZEX4441 alloy exhibited a fine homogeneous microstructure(average grain size of 2.8μm)with granular Al₁₁RE₃,fibrous Al₂REZn₂,and networked Ca₆Mg₂Zn₃ phases distributed at the grain boundaries.The room-temperature thermal conductivity of the HPDC AZEX4441 alloy was 94.4 W·m^-1·K^-1,which was much higher than 53.7 W·m^-1·K^-1 of the HPDC AZ91D alloy.Al and Zn in the AZEX4441 alloy were largely consumed by the formation of Al₁₁RE₃,Al₂REZn₂,and Ca₂Mg₆Zn₃ phases because of the addition of RE and Ca.Therefore,the lattice distortion induced by solute atoms of the AZEX4441 alloy(0.171%)was much lower than that of the AZ91D alloy(0.441%),which was responsible for the high thermal conductivity of the AZEX4441 alloy.The AZEX4441 alloy exhibited a high yield strength of~185 MPa,an ultimate tensile strength of~233 MPa,and an elongation of~4.2%.This result indicated that the tensile properties were comparable with those of the AZ91D alloy.Therefore,this study contributed to the development of high-performance Mg alloys with a combination of high thermal conductivity,high strength,and good castability.     

Corrosion behavior of as-cast Mg–8Li–3Al+xCe alloy in 3.5wt% NaCl solution

Mg–8Li–3Al+xCe alloys (x = 0.5wt%, 1.0wt%, and 1.5wt%) were prepared through a casting route in an electric resistance furnace under a controlled atmosphere. The cast alloys were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The corrosion behavior of the as-cast Mg–8Li–3Al+xCe alloys were studied under salt spray tests in 3.5wt% NaCl solution at 35°C, in accordance with standard ASTM B–117, in conjunction with potentiodynamic polarization (PDP) tests. The results show that the addition of Ce to Mg–8Li–3Al (LA83) alloy results in the formation of Al₂Ce intermetallic phase, refines both the α-Mg phase and the Mg₁₇Al₁₂ intermetallic phase, and then increases the microhardness of the alloys. The results of PDP and salt spray tests reveal that an increase in Ce content to 1.5wt% decreases the corrosion rate. The best corrosion resistance is observed for the LA83 alloy sample with 1.0wt% Ce.     

Development of high-strength,low-cost wrought Mg–2.0 mass% Zn alloy with high Mn content

Mg–Zn–Mn-based alloys have received considerable attention because of their high creep resistance, strength,and good corrosion resistance. The alloying element Mn in Mg–Zn-based alloys is commonly less than 1 wt%. In the present study, the effect of high Mn content(1 wt% and 2 wt%) on the microstructures and mechanical properties of Mg–2Zn–0.3Sr extruded alloy was investigated. The results revealed that the high Mn content significantly increased the ultimate tensile strength, tensile yield strength, compress yield strength, and yield asymmetry of the alloy without affecting its ductility. The dynamically recrystallized(DRXed) grains of Mg–2Zn–0.3Sr were remarkably refined because of the large amount of fine Mn precipitates in the homogenized alloy. The improved strengths were mainly attributed to the fine DRXed grains according to the Hall–Petch effect and to the large amount of spherical and 0001 Mn precipitates through the precipitation and dispersion strengthening. The fine DRXed grains and numerous Mn precipitates effectively suppressed the extension twining, substantially enhanced the compress yield strength, and resulted in improved anisotropy.     

TiB2和Al3Ti对近共晶Al?12.6Si合金组织、力学性能和断裂行为的影响

A near eutectic Al?12.6Si alloy was developed with 0.0wt%, 2.0wt%, 4.0wt%, and 6.0wt% Al?5Ti?1B master alloy. The microstructural morphology, hardness, tensile strength, elongation, and fracture behaviour of the alloys were studied. The unmodified Al?12.6Si alloy has an irregular needle and plate-like eutectic silicon (E_Si) and coarse polygonal primary silicon (P_Si) particles in the matrix-like α-Al phase. The P_Si, E_Si, and α-Al morphology and volume fraction were changed due to the addition of the Al?5Ti?1B master alloy. The hardness, UTS, and elongation improved due to the microstructural modification. Nano-sized in-situ Al₃Ti particles and ex-situ TiB₂ particles caused the microstructural modification. The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time. The Al?5Ti?1B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.     

Effects of heat treatment on the microstructure and mechanical properties of ZA84 magnesium alloy

The effects of heat treatment on the microstructure and mechanical properties of ZA84 (Mg-8Zn-4Al-0.25Mn) alloy were investigated. The results indicate that the as-cast microstructure of the alloy is mainly composed of α-Mg matrix and two different morphologies of precipitates (continuous and quasi-continuous Mg₃₂(Al,Zn)₄₉ phases and isolated Mg₅Al₂Zn₂ phases). After solid solution treatment at 345℃, the Mg₃₂(Al,Zn)₄₉ phases change from continuous and quasi-continuous net to disconnected acute angle shape, and parts of second phases sphericize. The optimum heat treatment condition for the alloy is solution treatment at 345℃ for 48 h and water quenching, then aging treatment at 200℃ for 12 h and atmosphere cooling. Under the optimum condition, the ultimate tensile strength and yield strength of the alloy can be imoroved, but the elongation is not effected much bv heat treatment.     

Microstructure evolution and mechanical properties of a large-sized ingot of Mg-9Gd-3Y-1.5Zn-0.5Zr (wt%) alloy after a lower-temperature homogenization treatment

In this paper, a large-sized ingot of Mg-9Gd-3Y-1.5Zn-0.5Zr (wt%) alloy with a diameter of 600 mm was successfully prepared by the semi-continuous casting method. The alloy was subsequently annealed at a relatively low temperature of 430℃ for 12 h as a homogenization treatment. The microstructure and room-temperature mechanical properties of the alloy were investigated systematically. The results show that the as-cast alloy contained a mass of discontinuous lamellar-shaped 18R long-period stacking ordered (LPSO) phases with a composition of Mg₁₀ZnY and an α-Mg matrix, along with net-shaped Mg₅(Y,Gd) eutectic compounds at the grain boundaries. Most of the eutectic compounds dissolved after the homogenization treatment. Moreover, the amount and dimensions of the lamellar-shaped LPSO phase obviously increased after the homogenization treatment. The structure of the phase transformed into 14H-type LPSO with composition Mg₁₂Zn(Y,Gd). The mechanical properties of the heat-treated large-sized alloy ingot are uniform. The ultimate tensile strength (UTS) and tensile yield strength (TYS) of the alloy reached 207.2 MPa and 134.8 MPa, respectively, and the elongation was 3.4%. The high performances of the large-sized alloy ingot after the homogenization treatment is attributed to the strengthening of the α-Mg solid solution and to the plentiful LPSO phase distributed over the α-Mg matrix.     

Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl(x=1, 3 and 5) alloys

As-extruded Mg–5Sn–1Zn–xAl alloys(x=1, 3, and 5) were fabricated by hot extrusion. The experimental results revealed that the yield strength of alloys initially decreased and then increased with the increase of Al content. These changes were mainly attributed to the difference in crystallographic texture and volume fractions of second phases. The ultimate tensile strength, yield strength, and elongation of the alloys were greater than 310 MPa, 227 MPa, and 11%, respectively. The strain hardening ability of the alloys was also discussed.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Effects of gadolinium addition on the microstructure and mechanical properties of Mg-9Al alloy

This research aims to study the significance of Gd addition (0wt%-2wt%) on the microstructure and mechanical properties of Mg-9Al alloy. The effect of Gd addition on the microstructure was investigated via X-ray diffraction (XRD), optical microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The Mg-9Al alloy contained two phases, α-Mg and β-Mg17Al12. Alloying with Gd led to the emergence of a new rectangular-shaped phase, Al₂Gd. The grain size also decreased marginally upon Gd addition. The ultimate tensile strength and microhardness of Mg-9Al alloy increased by 23% and 19%, respectively, upon 1.5wt% Gd addition. We observed that, although Mg-9Al-2.0Gd alloy exhibited the smallest grain size (181 μm) and the highest dislocation density (5.1×1010 m-2) among the investigated compositions, the Mg-9Al-1.5Gd alloy displayed the best mechanical properties. This anomalous behavior was observed because the Al₂Gd phase was uniformly distributed and present in abundance in Mg-9Al-1.5Gd alloy, whereas it was coarsened and asymmetrically conglomerated in Mg-9Al-2.0Gd.     

Effect of TiB_2 and Al_3Ti on the microstructure,mechanical properties and fracture behaviour of near eutectic Al-12.6Si alloy

A near eutectic Al-12.6 Si alloy was developed with 0.0 wt%, 2.0 wt%, 4.0 wt%, and 6.0 wt% Al-5 Ti-1 B master alloy. The microstructural morphology, hardness, tensile strength, elongation, and fracture behaviour of the alloys were studied. The unmodified Al-12.6 Si alloy has an irregular needle and plate-like eutectic silicon(E_(Si)) and coarse polygonal primary silicon(P_(Si)) particles in the matrix-like α-Al phase.The P_(Si), E_(Si), and α-Al morphology and volume fraction were changed due to the addition of the Al-5 Ti-1 B master alloy. The hardness, UTS,and elongation improved due to the microstructural modification. Nano-sized in-situ Al_3Ti particles and ex-situ TiB_2 particles caused the microstructural modification. The fracture images of the developed alloys exhibit a ductile and brittle mode of fracture at the same time. The Al-5 Ti-1 B modified alloys have a more ductile mode of fracture and more dimples compared to the unmodified alloy.     

Effect of annealing on the microstructure and mechanical properties of Mg-2.5Zn-0.5Y alloy

The microstructure and mechanical properties of extruded Mg-2.5Zn-0.5Y alloy before and after annealing treatments were investigated. The as-extruded alloy exhibits a yield tensile strength (YTS) of 305.9 MPa and an ultimate tensile strength (UTS) of 354.8 MPa, whereas the elongation is only 4%. After annealing, the YTS and UTS decrease to 150 MPa and 240 MPa, respectively, and the elongation increases to 28%. Interestingly, the annealed alloy maintains an acceptable stress level even after a much higher ductility is achieved. These excellent mechanical properties stem from the combined effects of fine α-Mg dynamic recrystallization (DRX) grains and a homogeneously distributed icosahedral quasicrystalline phase (I-phase) in the α-Mg DRX grains. In particular, the superior ductility originates from the coherent interface of I-phase and α-Mg and from the formation of the secondary twin {1011}–{1012}(38°<1210>) in the tension twin {1012}.     

Effect of homogenization process on the hardness of Zn–Al–Cu alloys

The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell “B” hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of the θ and τ' phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and temperature, used in their preparation.     

Effects of small additions of Zn on the microstructure,mechanical properties and corrosion resistance of WE43B Mg alloys

Zn is a commonly used alloying element for Mg alloys owing to its beneficial effects on mechanical properties. To improve the mechanical and corrosion properties of WE43B Mg alloys, the effects of 0-0.7wt% Zn addition on the microstructure and properties of sample alloys were investigated. Addition of Zn to as-cast WE43B alloy promoted the formation of the Mg₁₂Nd phase; by contrast, after T6 heat treatment, the phase composition of WE43B alloys with and without Zn addition remained mostly the same. A long-period stacking ordered phase was predicted by CALPHAD calculation, but this phase was not observed in either the as-cast or heat-treated Zn-containing WE43B alloys. The optimum temperature and duration of T6 heat treatment were obtained using CALPHAD calculations and hardness measurements. Addition of Zn resulted in a slight reduction in the average grain size of the as-cast and T6 heat-treated WE43B alloys and endowed them with increased corrosion resistance with little effect on their mechanical properties.     

Abrasive resistance of metastable V–Cr–Mn–Ni spheroidal carbide cast irons using the factorial design method

Full factorial design was used to evaluate the two-body abrasive resistance of 3wt%C–4wt%Mn–1.5wt%Ni spheroidal carbide cast irons with varying vanadium (5.0wt%–10.0wt%) and chromium (up to 9.0wt%) contents. The alloys were quenched at 920℃. The regression equation of wear rate as a function of V and Cr contents was proposed. This regression equation shows that the wear rate decreases with increasing V content because of the growth of spheroidal VC carbide amount. Cr influences the overall response in a complex manner both by reducing the wear rate owing to eutectic carbides (M₇C₃) and by increasing the wear rate though stabilizing austenite to deformation-induced martensite transformation. This transformation is recognized as an important factor in increasing the abrasive response of the alloys. By analyzing the regression equation, the optimal content ranges are found to be 7.5wt%–10.0wt% for V and 2.5wt%–4.5wt% for Cr, which corresponds to the alloys containing 9vol%–15vol% spheroidal VC carbides, 8vol%–16vol% M₇C₃, and a metastable austenite/martensite matrix. The wear resistance is 1.9–2.3 times that of the traditional 12wt% V–13wt% Mn spheroidal carbide cast iron.     

Effects of high-pressure rheo-squeeze casting on the Fe-rich phases and mechanical properties of Al-17Si-(1,1.5)Fe alloys

The effects of high pressure rheo-squeeze casting (HPRC) on the Fe-rich phases (FRPs) and mechanical properties of Al-17Si-(1,1.5)Fe alloys were investigated. The alloy melts were first treated by ultrasonic vibration (UV) and then formed by high-pressure squeeze casting (HPSC). The FRPs in the as-cast HPSC Al-17Si-1Fe alloys only contained a long, needle-shaped β-Al₅FeSi phase at 0 MPa. In addition to the β-Al₅FeSi phase, the HPSC Al-17Si-1.5Fe alloy also contained the plate-shaped δ-Al₄FeSi₂ phase. A fine, block-shaped δ-Al₄FeSi₂ phase was formed in the Al-17Si-1Fe alloy treated by UV. The size of FRPs decreased with increasing pressure. After UV treatment, solidification under pressure led to further refinement of the FRPs. Considering alloy samples of the same composition, the ultimate tensile strength (UTS) of the HPRC samples was higher than that of the HPSC samples, and the UTS increased with increasing pressure. The UTS of the Al-17Si-1Fe alloy formed by HPSC exceeded that of the Al-17Si-1.5Fe alloy formed in the same manner under the same pressure. Conversely, the UTS of the Al-17Si-1Fe alloy formed by HPRC decreased to a value lower than that of the Al-17Si-1.5Fe alloy formed in the same manner.