Mg-8Zn-4Al-(0～1)Sr镁合金铸态组织中的第二相研究

通过扫描电镜观察(SEM)、能谱分析(EDS)、X射线衍射分析(XRD)以及差热分析(DSC)等实验手段,系统地研究了添加微量Sr元素(质量分数0～1%)对铸态Mg-8Zn-4Al(ZA84)镁合金组织中的第二相种类的影响,并阐明了第二相形成与演变的内在机理。实验结果表明:未添加Sr元素的铸态Mg-8Zn-4Al合金组织由Q准晶相和少量Mg_(32)(Al, Zn)_(49)相组成。添加Sr元素后,合金铸态组织中均存在Al_4Sr和Mg_(32)(Al, Zn)_(49)相;其中Al_4Sr相随Sr含量增加而增加,Mg_(32)(Al, Zn)_(49)相随Sr含量增加而减少。在Mg_(32)(Al, Zn)_(49)相中Sr元素以未固溶和固溶两种形式存在,其中未固溶Sr元素的Mg_(32)(Al, Zn)_(49)相具有相对较高的Zn原子浓度和较低的Al原子浓度。相关结果将为第二相析出强化型Mg-8Zn-4Al合金的高强化与耐热化设计提供必要的理论支撑。     

Mg-Zn-Al合金的组织稳定性与力学性能

采用金相分析、DSC分析和拉伸测试等手段研究了铝含量对Mg-6Zn合金显微组织、凝固特性和力学性能的影响.结果表明,Mg-6Zn-2Al合金晶粒相对细小,具有最佳的强度与塑性组合;Mg-6Zn-6Al合金中晶界处存在接近连续分布的粗大鱼骨状金属间化合物Mg17Al12相,导致合金抗拉强度和塑性下降.长时间退火试验表明,Mg-6Zn-2Al具有较高的组织稳定性.因此,Mg-6Zn-2Al合金是Mg-Zn-Al系合金的一个较佳成分组合.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Sn对Mg-5Zn-2.5Al合金微观组织与性能的影响

利用光学显微镜、扫描电镜、万能试验机等分析测试设备研究了Sn对Mg-5Zn-2.5Al-xSn(x=0,1,2,3,4)(ZAT52x)合金组织结构及力学性能的影响.采用Thermo-Calc热力学软件计算了ZAT52x(x=0,2,4)3种合金在Scheil模型条件下液相质量分数与温度的关系以及凝固过程中的相变反应....     

Effects of Ce-rich RE on microstructure and mechanical properties of as-cast Mg-8Li-3Al-2Zn-0.5Nd alloy with duplex structure

The effects of Ce-rich RE on the microstructure and mechanical properties of as-cast Mg-8Li-3Al-2Zn-0.5Nd-x RE(x = 0, 1, 2, 3 wt%) alloys were investigated. The results indicated that the as-cast Mg-8Li-3Al-2Zn-0.5Nd alloy mainly consisted of α-Mg, β-Li, AlLi, MgLi2 Al and Al2 Nd phases. With the addition of Ce-rich RE in the alloy,Al3 RE and Al2 RE phases generated and gradually grew into net-like or block-like structure. With the addition of RE, Al-RE phases generated by consuming Al element and, thus, less Al element was dissolved in the matrix and less AlLi phase formed. Furthermore, less AlLi phase means that more Li element released to cause the increase ofβ-Li phase and refine the α-Mg phase. Under the influence of these factors, adding more RE led to higher elongation and lower tensile strength and hardness. With the addition of Ce-rich RE, the yield strength and ultimate tensile strength of the as-cast Mg-8Li-3Al-2Zn-0.5Nd alloy gradually decreased from 180 to 152 MPa and from 215 to 193 MPa, respectively, while the elongation was remarkably improved from 21.1% to 40.2%.     

Effects of P addition on the microstructure and mechanical properties of Mg–5%Sn–1.25%Si alloy

The effects of Al-P addition on the microstructure and mechanical properties of as-cast Mg–5%Sn–1.25%Si magnesium alloy were investigated. The results show that the phases of the as-cast alloy are composed of α-Mg, Mg2 Sn, Mg2 Si, little P, and AlP. The Chinese character shape Mg2 Si phase changes into a granular morphology by P addition because AlP can act as a heterogeneous nucleation core for the Mg2 Si phase. When 0.225wt% of Al–3.5%P alloy is added, the mechanical properties of the Mg–5%Sn–1.25%Si alloy are greatly improved, and the tensile strength increases from 156 to 191 MPa, an increase of 22.4% compared to the alloy without P addition. When the amount of Al–3.5%P reaches 0.300wt%, a segregation phenomenon occurs in the granular Mg2 Si phase, and the tensile strength and hardness decrease though the elongation increases.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

In vitro and in vivo studies on biodegradable magnesium alloy

The microstructure, mechanical property, electrochemical behavior and biocompatibility of magnesium alloy(Bio De MSM^TM) were studied in the present work. The experimental results demonstrated that grain refining induced by extrusion improves the alloy strength significantly from162 MPa for the as-cast alloy to 241 MPa for the as-extruded one. The anticorrosion properties of the as-extruded alloy also increased.Furthermore, the hemolysis ratio was decreased from 4.7% for the as-cast alloy to 2.9% for the as-extruded one, both below 5%. Bio De MSM^TMalloy shows good biocompatibility after being implanted into the dorsal muscle and the femoral shaft of the New Zealand rabbit, respectively, and there are no abnormalities after short-term implantation. In vivo observation indicated that the corrosion rate of this alloy varies with different implantation positions, with higher degradation rate in the femur than in the muscle.     

Mg-6Zn-(Al,Ca)镁合金显微组织及力学性能

利用WD-10A电子拉伸试验机和RD2-3型蠕变试验机对Mg-6Zn-(Al,Ca)系列镁合金的力学拉伸强度及高温蠕变性能进行测试,研究其显微组织对高温性能的影响,并利用金相显微镜、扫描电镜、X射线衍射分析等方法进行分析表征.研究结果表明,Mg-6Zn-2Al-0.3Mn(ZA62)具有较好的综合力学性能,其铸态显微组织主要由α-Mg基体和致密片状Mg51Zn20共晶相组成.少量Ca加入ZA62合金后,抑制了Mg51Zn20相的析出,并代之形成了含Ca的MgZn相和τ相.随Ca加入量增加,晶间相的数量增加,合金组织中出现另一热稳定四元Mg-Zn-Al-Ca化合物相.当w(Ca)>0.5%时,合金晶粒显著细化.随Ca含量增加,合金常温拉伸强度和塑性呈下降趋势,基体显微硬度减小.加入Ca提高了合金高温拉伸强度,改善了合金蠕变性能.在175℃/70 MPa条件下,合金蠕变性能受合金晶粒尺寸影响,随晶粒尺寸的减小,蠕变变形量增加.     

In vitro corrosion of Mg–1.21Li –1.12Ca –1Y alloy

The influence of the microstructure on mechanical properties and corrosion behavior of the Mg–1.21Li–1.12Ca–1Y alloy was investigated using OM, SEM, XRD, EPMA, EDS, tensile tests and corrosion measurements. The results demonstrated that the microstructure of the Mg–1.21Li–1.12Ca–1Y alloy was characterized by α-Mg substrate and intermetallic compounds Mg2 Ca and Mg24Y5. Most of the fine Mg2 Ca particles for the as-cast alloy were distributed along the grain boundaries, while for the as-extruded along the extrusion direction. The Mg24Y5 particles with a larger size than the Mg2 Ca particles were positioned inside the grains. The mechanical properties of Mg–1.21Li–1.12Ca–1Y alloy were improved by the grain refinement and dispersion strengthening. Corrosion pits initiated at the α-Mg matrix neighboring the Mg2 Ca particles and subsequently the alloy exhibited general corrosion and filiform corrosion as the corrosion product layer of Mg(OH)2and Mg CO3 became compact and thick.     

Preparation, microstructure and degradation performance of biomedical magnesium alloy fine wires

With the development of new biodegradable Mg alloy implant devices, the potential applications of biomedical Mg alloy fine wires are realized and explored gradually. In this study, we prepared three kinds of Mg alloy fine wires containing 4 wt% RE(Gd/Y/Nd) and 0.4 wt% Zn with the diameter less than 0.4 μm through casting, hot extruding and multi-pass cold drawing combined with intermediated annealing process. Their microstructures, mechanical and degradation properties were investigated. In comparison with the corresponding as-extruded alloy, the final fine wire has significantly refined grain with an average size of 3–4 μm, and meanwhile shows higher yield strength but lower ductility at room temperature. The degradation tests results and surface morphologies observations indicate that Mg–4Gd–0.4Zn and Mg–4Nd–0.4Zn fine wires have similar good corrosion resistance and the uniform corrosion behavior in SBF solution. By contrast, Mg–4Y–0.4Zn fine wire shows a poor corrosion resistance and the pitting corrosion behavior.     

Al含量对镁锂合金α-Mg相晶格常数及微观应变的影响

采用X射线衍射方法测算Ng-5Li-xAl合金α-Mg相晶格常数及微观应变,研究不同含量的Al元素对镁锂合金中α-Mg相晶格常数及微观应变的影响．结果表明,铸态blg-5Li-xAl合金主要是由α-Mg基体和AlLi相组成;随着Al含量增加,α-Mg相的衍射峰向高角度偏移,晶格常数下降,合金的微观应变增加,其原因是固溶进入α-Mg相基体中的A1原子和析出的A1Li相共同作用所致;铸态Mg-5Li-xAl合金的硬度随着Al含量增加而增大,Al添加量在3％～5％时合金硬度的增长率要高于Al添加量在0—3％时硬度的增长率．     

Microstructure evolution and mechanical properties of a large-sized ingot of Mg-9Gd-3Y-1.5Zn-0.5Zr (wt%) alloy after a lower-temperature homogenization treatment

In this paper, a large-sized ingot of Mg-9Gd-3Y-1.5Zn-0.5Zr (wt%) alloy with a diameter of 600 mm was successfully prepared by the semi-continuous casting method. The alloy was subsequently annealed at a relatively low temperature of 430℃ for 12 h as a homogenization treatment. The microstructure and room-temperature mechanical properties of the alloy were investigated systematically. The results show that the as-cast alloy contained a mass of discontinuous lamellar-shaped 18R long-period stacking ordered (LPSO) phases with a composition of Mg₁₀ZnY and an α-Mg matrix, along with net-shaped Mg₅(Y,Gd) eutectic compounds at the grain boundaries. Most of the eutectic compounds dissolved after the homogenization treatment. Moreover, the amount and dimensions of the lamellar-shaped LPSO phase obviously increased after the homogenization treatment. The structure of the phase transformed into 14H-type LPSO with composition Mg₁₂Zn(Y,Gd). The mechanical properties of the heat-treated large-sized alloy ingot are uniform. The ultimate tensile strength (UTS) and tensile yield strength (TYS) of the alloy reached 207.2 MPa and 134.8 MPa, respectively, and the elongation was 3.4%. The high performances of the large-sized alloy ingot after the homogenization treatment is attributed to the strengthening of the α-Mg solid solution and to the plentiful LPSO phase distributed over the α-Mg matrix.     

Composition design of superhigh strength maraging stainless steels using a cluster model

The composition characteristics of maraging stainless steels were studied in the present work investigation using a cluster-plus-glue-atom model. The least solubility limit of high-temperature austenite to form martensite in basic Fe–Ni–Cr corresponds to the cluster formula [NiFe12]Cr3,where NiFe12is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in FCC structure and Cr serves as glue atoms. A cluster formula [NiFe12](Cr2Ni) with surplus Ni was then determined to ensure the second phase(Ni3M) precipitation,based on which new multicomponent alloys [(Ni,Cu)16Fe192](Cr32(Ni,Mo,Ti,Nb,Al,V)16) were designed. These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1273 K for 1 h followed by water-quenching,and finally aged at 783 K for 3 h. The experimental results showed that the multi-element alloying results in Ni3M precipitation on the martensite,which enhances the strengths of alloys sharply after ageing treatment. Among them,the aged [(Cu4Ni12)Fe192](Cr32(Ni8.5Mo2Ti2Nb0.5Al1V1)) alloy(Fe74.91Ni8.82Cr11.62Mo1.34Ti0.67Nb0.32Al0.19V0.36Cu1.78wt%) has higher tensile strengths with YS?1456 MPa and UTS?1494 MPa. It also exhibits good corrosion-resistance in 3.5 wt% NaCl solution.     

Mg-7Sn-Zn(Y)合金的显微组织、时效硬化行为及力学性能

研究了Zn和Y合金化对Mg-7Sn合金显微组织、时效硬化行为和力学性能的影响.铸态Mg-7Sn合金主要由α-Mg和共晶(α-Mg+Mg₂Sn)相组成.Zn添加细化了Mg₂Sn相的尺寸,促进了Mg₂Sn相大量、均匀的弥散分布,同时诱导了Mg₂Sn相的非基面析出,增强了合金时效硬化效果.合金时效峰值硬度从64.6 HV增大到69.7 HV,峰值时效时间从166 h缩小至142 h.Zn和Y元素共同添加形成了针状MgSnY相,有效缩短了合金的时效峰值时间(由166 h缩短至120 h),但合金的峰值硬度略有降低,Mg-7Sn-1Zn合金具有最佳的力学性能,其高力学性能主要归结为细小、高体积分数Mg₂Sn相的析出强化.     

Corrosion study of resorbable Ca60Mg15Zn25 bulk metallic glasses in physiological fluids

The corrosion activity of amorphous plates of Ca_(60)Mg_(15)Zn_(25)alloy was investigated.The biocompatible elements were selected for the alloy composition.The electrochemical corrosion and immersion tests were carried out in a multi-electrolyte fluid and Ringer's solution.Better corrosion behavior was observed for the samples tested in a multi-electrolyte fluid despite the active dissolution of Ca and Mg in Ringer's solution.The experimental results indicated that reducing concentration of NaCl from 8.6 g/dm~3for Ringer's solution to 5.75 g/dm~3caused the decrease of the corrosion rate.The volume of the hydrogen evolved after 480 min in Ringer's solution(40.1 ml/cm~2)was higher in comparison with that obtained in a multi-electrolyte fluid(24.4 ml/cm~2).The values of opencircuit potential(E_(OCP))for the Ca_(60)Mg_(15)Zn_(25)glass after 1 h incubation in Ringer's solution and a multielectrolyte fluid were determined to be-1553 and-1536 m V vs.a saturated calomel electrode(SCE).The electrochemical measurements indicated a shift of the corrosion current density(j_(corr))from 1062μA/cm~2for the sample tested in Ringer's solution to 788μA/cm~2for the specimen immersed in a multi-electrolyte fluid.The corrosion products analysis was conducted by using the X-ray photoelectron spectroscopy(XPS).The corrosion products were identified to be CaCO_3,Mg(OH)_2,CaO,MgO and Zn O.The mechanism of corrosion process was proposed and described based on the microscopic observations.The X-ray diffraction and Fourier transform infrared spectroscopy(FTIR)also indicated that Ca(OH)_2,CaCO_3,Zn(OH)_2and Ca(Zn(OH)_3)_2·2H_2O mainly formed on the surface of the studied alloy.     

Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach

Cu-Ni-Si alloys are widely used due to their good electrical conductivities in combination with high strength and hardness. In the present work, minor-alloying with M =(Cr, Fe, Mo, Zr) was conducted for the objective of further improving their hardness while maintaining their conductivity level. A cluster-plus-glue-atom model was introduced to design the compositions of M-alloyed Cu-Ni-Si alloys, in which an ideal composition formula[(Ni,Si,M)-Cu_(12)]Cu_3(molar proportion) was proposed. To guarantee the complete precipitation of solute elements in fine δ-Ni_2 Si precipitates, the atomic ratio of(Ni,M)/Si was set as 2/1. Thus the designed alloy series of Cu_(93.75)(Ni/Zr)_(3.75)Si_(2.08)(Cr/Fe/Mo)_(0.42)(at%) were arc-melted into ingots under argon atmosphere, and solidsolutioned at 950 ℃ for 1 h plus water quenching and then aged at 450 ℃ for different hours. The experimental results showed that these designed alloys exhibit high hardness(HV 1.7 GPa) and good electrical conductivities(≥ 35% IACS). Specifically, the quinary Cu_(93.75)Ni_(3.54)Si_(2.08)(Cr/Fe)_(0.42)Zr_(0.21) alloys(Cu-3.32 Ni-0.93 Si-0.37(Cr/Fe)-0.30 Zr wt%) possess both a high hardness with HV = 2.5-2.7 GPa, comparable to the highstrength KLFA85 alloy(Cu-3.2 Ni-0.7 Si-1.1 Zn wt%,HV= 2.548 GPa),and a good electrical conductivity(35-36% IACS).     

Effect of annealing on the microstructure and mechanical properties of Mg-2.5Zn-0.5Y alloy

The microstructure and mechanical properties of extruded Mg-2.5Zn-0.5Y alloy before and after annealing treatments were investigated. The as-extruded alloy exhibits a yield tensile strength (YTS) of 305.9 MPa and an ultimate tensile strength (UTS) of 354.8 MPa, whereas the elongation is only 4%. After annealing, the YTS and UTS decrease to 150 MPa and 240 MPa, respectively, and the elongation increases to 28%. Interestingly, the annealed alloy maintains an acceptable stress level even after a much higher ductility is achieved. These excellent mechanical properties stem from the combined effects of fine α-Mg dynamic recrystallization (DRX) grains and a homogeneously distributed icosahedral quasicrystalline phase (I-phase) in the α-Mg DRX grains. In particular, the superior ductility originates from the coherent interface of I-phase and α-Mg and from the formation of the secondary twin {1011}–{1012}(38°<1210>) in the tension twin {1012}.     

Ti – Cu– Zr–Fe– Nb ultrafine structur e-dendrite composites with good mechanical properties and biocompat ibility

Ti-Cu-Zr-Fe-Nb ultrafine structure-dendrite composites were designed by inducing Nb and more Ti to a Ti-Cu-Zr-Fe glass-forming alloy composition and prepared by copper mold casting.The composite alloys consist of β-Ti dendrites and ultrafine-structured CuTi₂ and CuTi phases as well as a trace amount of glassy phase.The volume fraction of β-Ti dendrites increases with the increase in content of Nb which acted as the β-Ti phase stabilizer in the alloys.The composites exhibit high compressive yield strength exceeding1200 MPa,maximum strength around 1800 MPa and low Young’s modulus around 48 GPa.The plasticity of the alloys is strongly influenced by the volume fraction and morphology of the dendritic β-Ti phase,and the compressive plastic strain was enlarged from 5.9%for the 4 at%Nb alloy to 9.2%for the 8 at%Nb alloy.The preliminary cell culture experiment indicated good biocompatibility of the composite alloys free from highly toxic elements Ni and Be.These Ti-based composite alloys are promising to have potential structural and biomedical applications due to the combination of good mechanical properties and biocompatibility.     

Microstructure s and mechanical properties of Ti3Al/Ni-based superalloy joints arc welded with Ti –Nb and Ti– Ni – Nb filler alloys

Dissimilar joining of Ti3Al-based alloy to Ni-based superalloy has been carried out using gas tungsten arc(GTA) welding technology with Ti–Nb and Ti–Ni–Nb filler alloys.The joint welded with the Ti–Nb filler alloy contained much less interfacial brittle phases than the one using the Ti–Ni–Nb filler alloy.The average room-temperature tensile strength of the joint welded with Ti–Nb was 202 MPa and the strength value of the one welded with Ti–Ni–Nb was 128 MPa.For both fillers,the weak links of the dissimilar joints were the weld/In718 interfaces.The presence of TiNi,TiNi3 and Ni3Nb intermetallic compounds in the joint welded with Ti–Ni–Nb induced microcracks at the weld/In718 interface and deteriorated the mechanical properties of the joint.And the adoption of the Ti–Nb filler alloy decreased the formation tendency of interfacial brittle phases to some extent and thus enhanced the tensile strength of the joint.