高强高导Cu-Cr-Zr系合金的研究现状

从合金成分设计、析出相结构和制备技术三方面综述了高强高导Cu-Cr-Zr系合金的研究现状.在分析多种元素对合金强度影响的基础上,重点讨论了稀土元素的作用,适量稀土的加入能同时提高合金的硬度和电导率.Cu-Cr-Zr系合金的析出相主要是Cr和CuxZr（x=3,4,5）相,且合金在470 ℃时效4h形成有序的原子排列,其化合物类型为CrCu2（Zr,Mg）.固溶形变时效强化技术和快速凝固技术与常规固溶时效处理相比都能大大提高合金的综合性能.该类合金今后应向多元微合金化方向发展,尚待解决的主要问题是Zr、稀土等易烧损元素的熔炼较难控制.     

Cu-Ni-Si-Cr合金时效处理后的组织与性能

研究了时效与时效前的冷变形对Cu-2．37Ni-0．58Si-0．39Cr合金时效后硬度及导电率的影响，结果表明：合金经920℃固溶处理后，在500℃时效时可获得较高的硬度，而在550℃时效可得到较高的导电率；合金时效前的冷变形可加速时效析出，试样经80％变形后，在500℃时效1h，显微硬度可达HV271，而固溶态直接时效仅为HV239。合金在时效析出过程中有两种类型的析出相，分别为Cr3Si和Ni2Si。     

时效对Cu-Cr-Zr合金显微硬度及导电率的影响

探讨了时效工艺及形变量对Cu 0 .3Cr 0 .15Zr合金显微硬度及导电率的影响。结果表明 ,合金经 92 0℃固溶处理后在 4 2 0℃及 4 6 0℃时效可分别达到较好的硬度和导电率 ,分别达 183HV和 6 8%IACS ;时效前对合金加以适当冷变形可加速合金时效析出过程。影响合金导电率的主要因素是基体中固溶元素的含量 ,含量越高 ,导电率越低 ,反之则越高。而时效前冷变形可以增加合金内部位错等缺陷的数量 ,加速了合金第二相的析出。     

Ti_(30)Nb_5Ta_6Zr合金的组织和力学性能研究

根据β稳定化系数kβ和d-电子理论,采用无细胞毒性合金元素Nb、Ta、Zr,设计了具有低弹性模量的新型牙科种植用近β型Ti30Nb5Ta6Zr合金,研究了合金经不同温度固溶和时效处理后的显微组织和力学性能.结果表明,合金固溶后在低温时效时析出ω相导致合金脆性.随时效温度升高,析出相由ω逐步变为α并发生粗化,使合金强度降低,但塑性得到改善.固溶温度过低（700℃）,时效后强度较低 固溶温度过高（850℃）,导致合金出现β脆性.合金在750℃固溶和500℃时效12h后强韧性好,弹性模量低于现有Ti29Nb13Ta4.6Zr合金,综合力学性能可满足牙科种植合金的要求.     

形变热处理对Cu0.3Cr0.1Zr合金上引铸坯杆组织性能的影响

通过对上引Cu-0.3Cr-0.1Zr合金固溶处理、冷拉拔以及随后的时效处理工艺,研究冷拉拔形变及时效对材料力学性能、导电性能及组织结构的影响规律.结果表明:时效前的冷拉拔变形能提高Cu-0.3Cr-0.1Zr合金的力学性能而保持较高的导电率;合金在950 ℃固溶1 h后,经70%冷拉拔变形和500 ℃时效4 h,合金抗拉强度和导电率分别达到了418 MPa和87 %IACS;时效合金组织转变过程为:固溶体→G.P.区→Cr+Cu₄Zr,析出相对位错运动的阻碍是合金强化的重要机制.     

时效处理对Cu-Cr-Ti合金组织与性能的影响

由于高强、高导Cu-Cr-Zr合金在工业化生产熔炼时不易控制Zr的收得率,通过采用Ti替代Zr,以期获得易熔炼以及性能与Cu-Cr-Zr合金相当的时效强化型Cu-Cr-Ti合金。采用真空感应熔炼技术,经过热锻、固溶、冷轧、时效共4道工序,制备了Cu-Cr-Ti合金板材;对时效后的Cu-Cr-Ti合金的组织状态、析出相形态、析出相与基体的界面关系进行了分析;对合金的抗拉强度和导电率进行了测试。结果表明：450 ℃时效60 min后,Cu-0.45Cr-0.14Ti合金的综合性能最佳,抗拉强度和导电率分别达到620 MPa和64.9 %IACS;Cu-0.45Cr-0.14Ti合金中纳米尺寸的Cr强化相呈现椭圆形和双花瓣形,2种形状的析出相粒子均为面心立方结构,且均与基体保持完全共格关系。     

固溶时效对Cu-17Zn-0.4Cr合金硬度的影响

文章通过不同的热处理工艺来研究固溶时效对Cu-Zn-Cr合金硬度的影响.结果表明,经920 ℃、1 h固溶,再经475 ℃、1 h时效,合金的硬度能达到最大值120.5 HV.X射线衍射和扫描电镜研究表明,经920 ℃固溶475 ℃时效后,Zn在合金中与铜形成单相的α固溶体基体;有少量Cr在固溶过程中未溶入基体,此Cr粒子尺寸粗大;大多数Cr粒子为时效过程析出,在基体上呈细小弥散分布,这部分析出的Cr粒子是合金强化的主要原因.     

时效工艺对Cu-Ag-Zr合金电磨损性能的影响

对Cu-0．1Ag-0．18Zr合金时效后的电导率、显微硬度以及电滑动磨损性能进行了研究。结果表明：该合金940℃固溶1h后，在560℃时效可获得较高的电导率，在480℃时效可获得较高的显微硬度。时效前冷变形能大大加快第二相的析出过程，使合金综合性能显著提高。该合金经940℃固溶再经60％变形后，在480℃时效1h，其电导率和显微硬度分别可达85．6％IACS和HV131．2，而固溶后直接时效为81．3％IACS和HV116．1。在载流条件下，合金的磨损量随加载电流的增加而增大；磨损机制是以电蚀为主的电蚀、犁削和磨粒磨损。     

节镍无磁不锈钢Cr18Ni6Mn3N的组织及性能

研究了节镍无磁不锈钢Cr18Ni6Mn3N的热轧及固溶后的力学性能和耐蚀性能,分析了其固溶和时效析出后的组织演变规律、冷变形过程中形变诱发马氏体相变及其磁性能.结果表明:该不锈钢的固溶组织为单相奥氏体,其力学性能和耐蚀性能均高于SUS304不锈钢;800℃保温4 h后,在晶界析出粒状氮化物,随着保温时间延长,逐渐沿晶界凸起片层状析出物并向晶内生长,保温20 h后,凸出的片层状析出物直径达20μm.冷轧压下率18.3%时尚未发现形变诱发马氏体组织,随着变形量增大,马氏体含量增多,磁导率上升,但与相同条件下的SUS304不锈钢相比,冷轧板固溶后相对磁导率可降至1.002,因此可用于低成本无磁不锈钢领域.     

亚固溶温度热处理对 GH720Li 难变形高温合金γ相的影响

对难变形镍基高温合金 GH720Li 进行了亚固溶处理、亚固溶+单时效(650℃,24 h→空冷)或双时效处理(650℃,24 h→空冷+760℃,16 h→空冷)以及870℃时效3000 h 条件下γ相演变规律的研究。发现一次γ相受亚固溶处理影响较大,发生部分回溶的程度随固溶温度升高而增大,时效处理使一次γ相向球形或近球形转变;二次和三次γ相在亚固溶保温过程中完全回溶,在时效处理时补充析出明显且析出数量和区域随固溶温度升高而增大;870℃长期时效时,合金组织逐渐均匀,二次和三次γ相完全回溶,晶界一次γ相时效500 h 后有所粗化,合金硬度先降低而后保持不变。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.