粗晶粒铸轧AZ31镁合金的高温拉伸性能

研究了具有较大晶粒尺寸铸轧态AZ31镁合金的高温拉伸性能。通过热处理获得晶粒尺寸d=27.8μm的板材,对不同试样,在温度分别为300,350,400,450℃恒温条件下,以10^-3s^-1和10^-2s^-1恒定拉伸速率对试样进行拉伸至失效实验。结果表明,粗晶粒AZ31镁合金在450℃和10^-3s^-1条件下达到最大的延伸率106.7%。拉伸试样断口形貌的分析表明,450℃时出现丝状物质是合金出现液态Zn的结果。少量的液相可以释放应力集中和协调此时的变形过程。与细晶粒铸轧态AZ31相比,在拉伸条件相同和晶粒尺寸不同的情况下,粗晶粒的塑形较低,其原因是晶界滑移在变形时所作贡献少。     

AZ31B合金的铸轧组织

利用金相及扫描电镜对AZ31B 合金热模拟和铸轧样组织结构进行研究.研究结果表明在不同应变量下,热模拟样品的晶粒粒度均随应变速率的增加而减小,而当其他条件相同时,变形量越大晶粒粒度越小,冷却强度降低,合金呈典型铸态组织;利用铸轧技术生产的AZ31B 合金,当应变速率一定时,随着初始铸轧温度的降低,铸轧态板材的树枝晶粒度逐渐减小;而在初始铸轧温度一定时,随着应变速率的增大,铸轧态合金板材的树枝晶粒度也逐渐减小;而随着应变速率的提高,树枝晶沿轧向呈流线状排列的趋势增强;在AZ31B 合金铸轧过程中,轧制力不能太大,否则容易引起热裂.     

铸轧AZ31镁合金的高温拉伸性能

研究了铸轧AZ31镁合金的高温拉伸性能和变形机制.在300～450℃条件下,分别以恒定拉伸速率10^-3s^-1和10^-2 s^-1进行拉伸至失效试验,在真实应变率为2×10^-4～2×10^-2 s^-1的范围内进行变应变率拉伸试验.当拉伸速率为10^-2s^-1时,试样在400℃和450℃的延伸率均超过100%;当拉伸速率为10^-3 s^-1时,试样在400℃和450℃的延伸率均超过200%,该条件下的应力指数n≈3,蠕变激活能Q=148.77 kJ·mol^-1,变形机制为溶质牵制位错蠕变和晶界滑移的协调机制.通过光学金相显微镜和扫描电子显微镜观察显示试样断口处存在由于发生动态再结晶和晶粒长大而形成的粗大晶粒,断裂形式为空洞长大并连接导致的韧性断裂.     

Zn-5%Al共晶合金超塑性变形特性的研究

研究了热轧态的Zn-5％Al共晶合金超塑性变形的力学行为及其显微组织的变化。结果表明:温度和应变速率对合金超塑性的力学性能影响很大。由于Zn-5％Al共晶合金具有优良的稳定组织,其最佳超塑性出现在较高的温度(300℃)和中等应变速率(1.67×10~(-4)s~(-1))条件下。随着温度提高到340℃,热长大已成为晶粒长大的主要因素。提高变形温度(300℃),可以使Zn-5％Al合金以较小的应力(25 MPa)和较高的应变速率(1.67×10~(-2)s~(-1))超塑性变形。     

Mg-4Sn-1Ce合金的组织及热压缩行为

本文采用光学金相显微镜(OM)、X射线衍射(XRD)、扫描电镜(SEM)以及热压缩实验对Mg-4Sn-1Ce合金的微观组织和热压缩行为进行了研究。结果表明,铸态合金主要由"岛"状的α-Mg、Mg_2Sn、Ce_4Sn_5和MgSnCe相组成。合金在250～450℃和0.001～1s~(-1)应变速率下进行热压缩,热变形激活能Q为162.03 kJ/mol,本构方程为■=1.3×10~(12)·[sinh (0.019σ)]~(5.6)exp[-162030/(RT)]。热压缩温度由250℃升高到450℃,合金显微组织由(扁平状晶粒+挤压流线)组织演变为再结晶等轴晶粒组织。     

Zener-Hollomon参数对AZ61镁合金热变形行为的影响

利用Gleeble-3500热模拟试验机,对均匀化退火处理后的铸态AZ61镁合金进行了等温热压缩变形实验,研究了合金在变形温度为220℃～380℃、应变速率为0.001 s~(-1)～10 s~(-1)条件下的热变形行为和组织演变特征,并基于双曲正弦模型建立了合金的本构模型。研究了Zener-Hollomon参数对热压缩变形组织演变的影响规律,揭示了高Z值、中等Z值和低Z值对应参数条件下的变形合金呈现不同的组织形貌特征,并阐明了随Z参数的逐渐减小,变形组织逐渐由失稳组织、不完全动态再结晶组织转变为粗化的完全动态再结晶组织,确定了合理的热成形工艺参数区间对应的lnZ数值范围为22.17～29.25。     

变形参数对AZ31镁合金变形抗力的影响

利用Gleeble-1500热模拟试验机对AZ31镁合金在变形温度为250～400℃、变形速率为0.5～3.0s-1下进行热变形模拟实验,得到了AZ31镁合金真实应力-真实应变曲线,并通过光学显微镜观察了试样在变形中的微观组织.结果表明,动态再结晶是该实验条件下晶粒细化的主要机制,变形参数影响了再结晶的程度.     

铈对AZ31镁合金铸态组织的影响

研究了Ce对AZ31镁合金铸态组织的影响.研究结果表明:添加0.5～1.5 wt%Ce到AZ31镁合金中不但不能细化舍金的晶粒,反而使合金的晶粒变得粗大,并且粗化趋势受Ce加入量的影响较大.当添加0.5 wt%Ce到AZ31镁合金中后,合金的平均晶粒尺寸从最初的60靘增大到164靘.此后,随着Ce加入量从0.5 wt%增加到1.5 wt%,合金的平均晶粒尺寸又开始逐渐减小,但仍大于未添加Ce合金的平均晶粒尺寸.     

AZ31镁合金加工图研究

采用加工图理论系统的分析了AZ31镁合金在高温变形过程中的变形行为。结果表明:AZ31镁合金在塑性变形行为过程中发生动态再结晶,温度的升高和应变速率的降低有利于动态再结晶形核的形成与长大。采用加工图理论分析AZ31镁合金高温下的塑性变形行为并至关反映变形后AZ31镁合金材料的组织演化以及性能变化规律。由加工图可知材料的最佳变形条件:压缩变形过程温度为320℃~360℃、应变速率为0.5~0.05 s-1;拉伸变形过程温度为350℃~400℃、应变速率为0.001~0.000 33 s-1.     

喷射沉积AZ31镁合金微观组织与力学性能

采用喷射沉积方法制备了AZ31镁合金沉积柱坯,利用热轧作为后续加工,研究了镁合金的组织变化及材料的性能.实验结果表明:沉积态合金组织均匀,晶粒细小(平均晶粒尺寸约为20μm);热轧变形的致密化过程、动态再结晶以及退火再结晶使合金具有良好的组织结构和力学性能;轧制态试样断口呈现为脆性解理断裂方式,退火态试样断口则表现为脆性和韧性断裂混合机制.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.