石参膳食纤维制备工艺优化研究

为研究膳食纤维制备工艺及物化特性,以独尾草(Eremurus chinensis Beib.)肉质根加工品(石参)为研究材料,通过单因素试验和响应面分析,确立了酸碱法制备石参膳食纤维的工艺条件。其优化后的基本工艺参数为原料颗粒直径0.3 mm,碱液浓度0.58 mol/L,碱液料液比1∶10,碱液浸提时间88.93 min,碱液浸提温度58.56℃,酸液浓度10%,酸液料液比1∶10,酸液浸提时间60 min和酸液浸提温度61.44℃;此条件下的理论得率为15.65%。     

方格星虫多糖碱法提取工艺研究

【目的】研究碱法提取方格星虫体壁中水溶性方格星虫多糖的条件及优化。【方法】根据料液比、浸提时间、浸提温度、碱液浓度对多糖得率的影响,并通过正交试验得到方格星虫水溶性多糖浸提工艺优选因素组合。【结果】影响方格星虫多糖得率的因素主次顺序为浸提温度料液比浸提时间碱液浓度;最佳浸提条件为温度50℃,料液比1∶6g/mL,时间4h,碱液(NaOH)的质量分数为8%。【结论】最佳浸提工艺条件下多糖浸提提取率最大为1.81%。     

葡萄籽油的提取和精炼工艺研究

对葡萄籽油提取和精炼工艺进行了研究.结果表明,在文中的试验条件下,葡萄籽油浸提最佳工艺条件是:石油醚为浸提剂,葡萄籽粒度60目、含水量7.0%、料液比1 g∶7 mL、温度70℃、浸提时间4h.葡萄籽油精炼工艺条件是:碱炼初温45℃,碱液浓度9.50%,超碱用量0.3%;水化加水量2%,水化时间分别为1.0、0.5 h;二次脱色工艺为活性脱色白土,加量第1次1%,脱色时间30 min、脱色温度80℃,第2次加量1%,脱色时间15 min,温度85℃,真空度0.08 MPa;在真空度0.08 MPa、温度180℃、脱臭时间1 h条件下可以脱除葡萄籽油中的臭味成分,保持葡萄籽的固有香味.     

葡萄籽蛋白提取工艺研究

采用碱溶酸沉法对葡萄籽蛋白提取工艺进行了研究.结果表明：葡萄籽粉碎粒度为40目,以pH值为9的碱液,按m（料）∶V（液）=1∶10,在50℃条件下搅拌浸提45min时,蛋白质的提取最经济.     

丹参水溶性糖蛋白的提取及其理化性质

采用单因子试验和L9(34)正交试验设计对丹参糖蛋白的水提醇沉工艺及一般理化性质进行了研究,试验了料液比、提取时间、提取温度和盐浓度对丹参水溶性糖蛋白提取的影响.结果表明,影响糖蛋白得率的主次因素为料液比、浸提温度、浸提时间、盐浓度,最佳提取工艺条件为料液比1∶20,提取温度70℃,提取时间4h,0.1 mol/L的NaCl,Savage法脱蛋白7次,80%乙醇醇析.在此最佳工艺条件下,糖蛋白得率为5.03%.理化性质研究结果表明,提取物是糖含量为26.24%、蛋白质含量为37.34%的高中分子量范围内的酸性糖蛋白.     

蚂蚁蛋白质提取方法的比较研究

以铺道蚁(Tetramorium caespitum)为实验材料,采用正交试验法,对蚂蚁蛋白质的提取条件进行了研究.实验分别采用碱提蛋白法、盐提蛋白法、Tris-HCl缓冲液提蛋白法等3种提取方法.对其主要条件:不同浓度、浸提温度、浸提时间、固液比以及Tris-HCl液的pH值等进行了研究.结果表明,碱提蛋白法的最佳条件为:碱液浓度为1%,固液比为1∶15,浸提时间为60 min,浸提温度为80℃;盐提蛋白法的最佳条件为:盐液浓度为1.5%,固液比为1∶15,浸提时间为60 min,浸提温度为50℃;Tris-HCl缓冲液提蛋白法的最佳条件为:pH值为8.3,固液比为1∶15,浸提时间为90 min,浸提温度为20℃.在这3种方法中,碱提蛋白法的蛋白质得率最高,其次为盐提蛋白法,而Tris-HCl缓冲液提蛋白法最低.     

超声波辅助碱提取福建黄花梨皮多糖工艺研究

通过选取福建黄花梨皮为原材料,采用超声波辅助碱提取的方法提取福建黄花梨皮中的多糖,运用苯酚-硫酸法测定其多糖含量。首先通过单因素试验,研究各单因素:超声波提取温度、超声波处理时间、氢氧化钠碱液浓度、料液比对多糖提取率的影响,再利用L_9(3~4)进行正交设计试验。研究结果表明,福建黄花梨皮中多糖提取的最优工艺参数:超声波提取温度为45℃,超声波处理时间为60 min,氢氧化钠浓度0. 2 mol/L,料液比1∶40,在此条件下多糖的提取率可以达到57. 76%。     

BCA法优化补骨脂蛋白质的提取工艺

采用碱提酸沉法提取补骨脂蛋白质,以二喹啉甲酸(BCA)法测定的蛋白质溶出率为指标,通过单因素实验和正交实验优化补骨脂蛋白质的碱提工艺条件,考察浸提p H、料液比、温度、时间等因素对补骨脂蛋白质提取的影响.结果表明,四种提取因素的影响从大到小的顺序为:浸提p H料液比温度时间.最佳工艺条件为浸提p H 10.0、料液比(g/m L)1∶20、温度45℃、浸提时间150 min,此条件下补骨脂蛋白质溶出率为23.69%.以BCA法测定酸沉蛋白质浓度,确定补骨脂蛋白质的最大沉淀量p H为4.5,蛋白质的最大沉淀率为55.16%.对比发现理论提取率与实际提取率基本相同,证明BCA法测定补骨脂蛋白质的方法准确、可靠,为补骨质蛋白质的进一步研究利用奠定了基础.     

浒苔多糖的碱法提取工艺研究

对浒苔多糖的碱法提取工艺进行研究,为评价提取条件对浒苔多糖提取率的影响,首先选用固液比、浸提温度、浸提时间和碱溶液浓度4个因素进行单因素多水平实验,在此基础上进行正交试验,筛选出最佳提取工艺条件.实验结果表明,影响浒苔多糖提取率的各因素的主次关系依次为:浸提温度、浸提时间、固液比,碱溶液浓度;浒苔多糖碱法提取的最佳工艺条件为:提取温度90℃,提取时间2.5h,固液比1:40(g:mL),氢氧化钠溶液浓度0.3mol/L;最佳工艺条件下,浒苔多糖的提取率为3.1%.     

柚叶多酚的提取工艺优化

本文以柚叶为原料,研究从柚叶中提取多酚的工艺,利用单因素和响应面试验对提取工艺中影响柚叶多酚提取率的工艺参数(乙醇浓度、浸提时间、液料比、提取温度)进行了分析与优化.结果表明,柚叶多酚的最佳工艺条件为:乙醇浓度60%、浸提时间100 min、液料比20 m L·g-1、提取温度70℃,柚叶多酚提取率为22.76 mg·g-1,与模型预测值(22.88 mg·g-1)相比,其相对误差为0.52%,验证了该模型的有效性和实用性.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.