烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

氧化锌矿物浸出渣中铅、锶的提取及动力学分析

NH₄HCO₃ conversion followed by HCl leaching was performed and proven to be effective in extracting Pb and Sr from zinc extracted residual. The mechanism and operating conditions of NH₄HCO₃ conversion, including molar ratio of NH₄HCO₃ to zinc extracted residual, NH₄HCO₃ concentration, conversion temperature, conversion time, and stirring velocity, were discussed, and operating conditions were optimized by the orthogonal test. Experimental results indicate that NH₄HCO₃ conversion at temperatures ranging from 25 to 85°C follows the shrinking unreacted core model and is controlled by inner diffusion through the product layer. The extraction ratios of Pb and Sr under optimized conditions reached 85.15% and 87.08%, respectively. Moreover, the apparent activation energies of Pb and Sr were 13.85 and 13.67 kJ·mol?1, respectively.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

在直径为d的树中具有极小GA2的树

Tabar等人定义了图的第二类几何-算术指标GA2,同时给出了任意连通图G的可达上下界,并分别刻画了：在有n个顶点的树中Pn具有极大GA2,K1,n-1具有极小GA2.刘颖在有n个顶点的树中确定了具有GA2前五小的图及在具有完美匹配的所有树中具有GA2前四小的图.在此基础上,本文给出直径固定且有n个顶点的树中具有极小GA2的图.     

混凝土剪压强度相关性规律理论研究

将混凝土剪压（包括剪拉）强度相关性规律统一表达为三参数椭圆公式或两参数椭圆公式其中,三参数椭圆公式符合某些试验结果：而两参数椭圆公式,或是由三参数椭圆公式简化而来,或是由双参数强度准则导出的,将它们分别与试验公式作了比较,其中之二也是可用的     

五种预氧化工艺处理污染原水的消毒性能比较

观察了水中腐殖酸和乳糖蛋白胨培养液的含量变化对高锰酸钾、氯、氯胺单独处理工艺及高锰酸钾与氯或氯胺联用工艺消毒效果的影响．结果表明，有机物浓度越高，高锰酸钾与氯或氯胺联用工艺与单独氯或氯胺工艺消毒效能相比所占优势越明显，尤其是当水中含有大量有机氮化合物时，采取高锰酸钾与氯或氯胺联用能更有效提高预处理时消毒效能．对有机污染严重的水源水进行预处理时，高锰酸钾与氯或氯胺联用预氧化能够减少有机物对消毒效果的影响，发挥预处理工艺对致病微生物的多级屏障作用，保障供水安全。     

鲨软骨粘多糖的酶法提取及组分分析

通过正交实验法分别研究单酶法提取次数和双酶法不同提取方式对鲨软骨粘多糖提取率的影响,从而获得胰蛋白酶和／或木瓜蛋白酶水解鲨软骨提取粘多糖的最佳工艺：并采用乙酸纤维素薄膜电泳和琼脂糖凝胶电泳分析不同提取方法获得的粘多糖的组分．实验结果表明：双酶水解方式比单酶水解方式的软骨降解率和多糖提取率要高;在双酶水解方式中,木-胰方式比胰-木方式能更有效地降解软骨,并且能获得更高的粘多糖提取率;而木瓜蛋白酶法提取的粘多糖纯度比胰蛋白酶法高．     

《大学语文》教学的若干思考与实践

本文从长期的教学实践中，探索出在《大学语文》古代文学教学中，应贯穿以史带文，以文述史，以赏促读，读赏结合，文以载道，文道合一的原则。     

重型颅脑交通伤的临床特点及救治要点

目的 :分析重型颅脑交通伤的临床特点及救治要点。方法 :回顾性分析我科2000年1月—2003年12月的64例重型颅脑交通伤病例的临床特点、CT资料及救治后的结果。分析原发昏迷时间、入院时GCS评分、救治措施与预后的关系。结果 :64例伤员中 ,单纯颅脑损伤24例 ,多发伤40例。原发性昏迷51例 ,继发性昏迷8例。GCS评分3～5分20例 ,5～8分44例。开颅手术23例 ,其它手术15例 ,气管切开35例。死亡22例 ,植物生存4例 ,重残2例 ,中残6例 ,恢复良好30例。结论 :重型颅脑交通伤伤情重、复合伤多、伤情复杂。及时有效的院前急救及入院后处理对患者的预后有重要意义     

高职教育督导的八大误区与突破创新

高职教育督导应走出误区,保持正确的方向,始终坚持教学督导与教育督导相结合、常规督导与专项督导相结合、事后督导与事前督导相结合、"督"与"导"相结合、校内督导与社会评价相结合、课堂督导与实践教学督导相结合、督教与督学和督管相结合、教学活动督导与设备利用督导相结合,以全面提高教育教学质量与人才培养质量。     

具有约束条件的均衡规划问题的微分方程方法

提出了具有不等式约束的均衡规划问题,运用该均衡规划问题的拉格朗日函数和投影算子将具有不等式约束的均衡规划问题转化为方程组.进一步,应用所得到的方程组建立了具有控制过程的微分方程系统,并证明了具有控制过程的微分方程系统的解的聚点是具有不等式约束的均衡规划问题的解.最后,给出了2个具有不等式约束的均衡规划问题的数值算例,并分别运用具有控制过程的微分方程系统对其进行求解,描绘了每个算例的微分方程系统的解的轨迹图,从图中可以明显地观察到具有控制过程的微分方程系统的解的轨迹收敛于均衡规划问题的解,从而说明了微分方程方法求解具有不等式约束的均衡规划问题的可行性和有效性.     

浅谈果蔬贮藏保鲜新技术

概括分析了减压贮藏保鲜、电离辐射贮藏保鲜、保鲜剂处理、细胞间水结构化气调保鲜、临界低温高湿保鲜、高压静电场保鲜、生物技术保鲜等国内外果蔬贮藏保鲜新技术。     

指标方程有特殊根时三阶线性方程的解

用幂级数解法或合成解法解有正则奇点的三阶线性方程,它的指标方程的根之差为整数（包括重根）时,不能求全部解．但已知一个或两个解后,用降阶法可求所缺的解．用合成解法求解有极点的三阶线性方程,当指标方程有二重根时,由非重根得一个解．然后利用降阶法求所缺的解;指标方程有三重根时作变量变换可以求解．笔者解决了这些问题,与文献[1]一起构成了三阶线性方程的完整解法．