烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

含钛高炉炉渣微波合成碳化钛及其介电性能测定

The preparation of functional material titanium carbide by the carbothermal reduction of Ti-bearing blast furnace slag with microwave heating is an effective method for valuable metals recovery; it can alleviate the environmental pressure caused by slag stocking. The dynamic dielectric parameters of Ti-bearing blast furnace slag/pulverized coal mixture under high-temperature heating are measured by the cylindrical resonant cavity perturbation method. Combining the transient dipole and large π bond delocalization polarization phenomena, the interaction mechanism of the microwave macroscopic non-thermal effect on the titanium carbide synthesis reaction was revealed. The material thickness range during microwave heating was optimized by the joint analysis of penetration depth and reflection loss, which is of great significance to the design of the microwave reactor for the carbothermal reduction of Ti-bearing blast furnace slag.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

普通话朗读中的停延

学习普通话的重要环节是在语流中模仿普通话的节律。停延作为节律的基础,确定了语流中的音步组合,进而关系到协同发音、连续变调等一系列语音现泉。停延的研究对于普通话的朗读教学具有重要的现实意义。该文以《普通话水平测试实施纲要》提供的60篇短文为语料,对于文中的停顿做出了定量、定性的分析：普通话的音步组合层的平均长度为5—7个音节,影响各篇短文音步组合层长度的主要因素是文体风格。该文根据60篇短文的语音资料,提出了设置句中无标点停顿的语义原则、语法原则、语用原则。根据语义原则,只能在有助于语义表达的地方停顿。根据语法原则,只能在构成语法结构的地方停顿。如果在某种情况下构成了非语法停顿,那是为了满足节律的需要。根据语用原则,人们通过对语境的分析,以停顿为手段,实现表情达意的最佳效果和节奏的匀称感。文中以大量例句,对各种语法结构中的语音停顿现泉进行比较说明,做出了令人信服的阐释。     

石油勘探开发建设项目评价系统探讨

石油勘探开发建设项目评价是石油勘探开发建设项目管理的重要内容之一,也是提高项目决策科学性的一个重要环节。首先分析了石油勘探开发建设项目评价的理论和方法,然后从项目前评价、项目中评价、项目后评价、技改项目评价四部分讨论了项目评价的基本内容,并在此基础上构建出了新的项目评价系统。指出:新的项目评价系统与传统的评价系统[1]的最大区别在于增加了项目中评价内容,并且对其它大、中型建设项目也是适用的。     

试验机稳定加载条件的修正及伺服控制的本质

本文通过对试验机-试样系统的分析,认为试验的稳定加载条件不仅仅取决于试验机和试样的刚度(K_m+K_r),而且取决于试验机活塞(端部)的位移速率.具有反馈系统的伺服试验机,正是通过对活塞位移U_q的控制来谐调刚度(K_m+K_r)的变化,从而达到控制应变速率,以保证加载过程的稳定.     

不同碳氮源对嗜热菌BF80生长和降解苯酚的影响

探测了蛋白胨,酵母粉,葡萄糖对BF80菌生长和降解苯酚的影响．结果表明：与对照相比,0．05％-1％的蛋白胨能促进BF80的生长却抑制该菌的苯酚降解,这种作用随浓度的增加而增大;酵母粉对BF80生长和苯酚降解均有促进作用,在最适浓度0．1％的情况下其生长量OD600达到1．578,苯酚降解率上升到99．21％;不同浓度的葡萄糖对BF80的生长和苯酚降解几乎都没有影响．     

建构中国古代文学审美理论:动因和方法

从提高“”的审美能力、“史”的认知能力、“论”的理解能力等方面阐述了建构中国古代学审美理论体系的动因，从注重古人创作和审美的实际、用今人的观点来透视、把定向观照和多向思维结合起来等方面探讨了建构这种理论的方法。目的在于使中国古代学理论的研究既有传统性又有现代性，既有本土性又有世界性。     

甘草的生药解剖学研究

观察比较三个甘草种１～４年生主根及根茎内部结构，主根共同特征和次生结构与一般双子叶植物基本相同．各年主根增粗主要是次生维管束个数稍有增多，射线、木射线伸入根中心，致使细胞增多、增大．根茎具有茎次生结构．三个种的粉末可看到淀粉粒、纤维、导管、品鞘纤维、射线薄壁细胞、筛管、棕色块、木栓细胞．     

应用于周期间歇性脉冲负载的复合电源机理与实验研究

针对周期间歇性脉冲负载对蓄电池循环寿命的影响,优化蓄电池的工作状态,引入蓄电池－超级电容器复合电源解决方案,充分发挥蓄电池比能量大和超级电容器比功率大的优势.选择蓄电池与超级电容器直接并联的被动式结构复合电源作为研究对象,并对被动式结构复合电源结构进行改进.在MATLAB仿真环境下,对应用于周期间歇性脉冲负载的蓄电池单一电源、被动式结构复合电源和改进型被动式结构复合电源进行对比仿真研究,同时搭建实验平台,进行对比实验研究.仿真和实验结果均表明,改进型被动式结构复合电源相比于其他两种电源,由于超级电容器对蓄电池功率的充分补偿,蓄电池放电过程得到优化,伴随着放电电流曲线更加平滑.     

三昧:佛教审美感悟的主要形式

佛教对中国古代学创作和审美产生了巨大影响，这已经是不争的问题。而在感应外物的心理知觉上与学审美究竟有何内在联系及区别，则又大多语焉不详，或详而无纲、油水分离。笔从佛教教义中拈出“三昧”两个字，深入探寻佛教审美感悟的主要方式，分析它与庄子“心斋”及俗人梦幻的同异，这对中国古代学审美理论的梳理和建构都有重要意义。     

隐喻:科学与人文的互补整合机制

文章通过语言隐喻性本性的阐述,提出了隐喻同样是人类理性的题中应有之义的思想．并以数学史中逻辑与直觉、精确与模糊的互补性,科学范式中的人文价值因素为佐证,论述了隐喻是科学与人文互补整合机制的一个方面或环节。而理性忘却了其隐喻的基础和功能,人类为此付出了沉重的代价（如全球性问题）。文章通过对科学前沿有关“不确定性”信息的反思．认为“不确定性”并不是什么“科学的终结”．而是意味着无限发展的可能性,预示着一种新的科学范式的诞生乃至一场新的科学革命的来临。其核心是超越旧的理性形式、建构新的理性形式。