基于40Cr高温动态力学性能的磨削表面动态再结晶行为

通过分离式霍普金森压杆(SHPB)实验得到了40Cr合金钢在高温高应变率下真应力-真应变曲线，据此确定了材料发生动态再结晶的临界条件.采用解析法和实验法分别求解了磨削强化层的温度场和塑性应变场分布.结果表明，磨削强化层在磨削深度方向具有较大的温度和塑性应变梯度;150μm强化层内会发生奥氏体转变;磨削表面最高温度可达1060℃.在磨削亚表面60μm内会产生剧烈的塑性变形，达到了再结晶的临界条件.较大的磨削深度使磨削强化层塑性应变增大，再结晶现象越充分，微观组织细化程度越高.     

螺栓连接大变形梁非线性振动特性的实验研究

柔性机械臂、大型可展开天线等机械结构的动作精度受运动过程中大变形几何非线性和连接处接触非线性的影响十分显著。以含螺栓连接结构的大变形梁作为研究对象，针对动力学建模和振动特性开展了实验研究，通过数值计算验证了实验发现的非线性振动特性。搭建了含螺栓连接柔性大变形梁的实验台架，开展了敲击和正弦激振的实验测试。实验结果表明，螺栓连接的柔性梁较连续梁的（无螺栓连接）模态频率降低，阻尼增加，反映出随着激励能量增大，模态频率降低的非线性模态特征。改变螺栓连接位置会显著影响结构的模态频率，其变化规律可由求解线性矩阵特征值定性反映。     

一种含N低Ni经济型双相不锈钢的抗氢脆性能的研究

设计了一种新型低Ni经济型双相不锈钢，通过金相显微镜、X射线衍射仪和扫描电子显微镜对不同固溶温度处理后的试样进行表征，通过常规拉伸实验得到综合力学性能最佳的热处理温度点，并通过电化学预充氢后的慢应变速率拉伸实验探究了其氢脆敏感性能。实验表明，随着温度的升高，奥氏体体积分数明显下降，铁素体体积分数升高，氢在双相不锈钢中的扩散能力提高。在1 050 ℃下固溶处理5 min后水淬的经济型双相不锈钢（lean duplex stainless steel，LDSS）综合性能最佳，其屈服强度和抗拉强度分别为744.7 MPa和807.7 MPa，总伸长率为62%，并且该材料在不同温度都具有优异的加工硬化性能。通过对1 050 ℃热处理后的试样进行不同电流密度和时间的预充氢处理，发现其氢脆敏感性能受充氢时间影响大于充氢电流，氢原子主要在塑性变形阶段降低材料抗拉强度和伸长率，对屈服强度影响较小。     

基于动态优化双钻头打孔机生产效能的研究

首先,对孔型加工及走刀方式进行分析,为提高打孔机效能,采用两钻头同时作业的方式。然后,根据相关的数据,应用动态优化的相关理论建立数学模型,并运用遗传算法进行求解,从而确立了双钻头作业时的最优作业线路、最佳行进时间和作业成本,并用MATLAB编写程序画出了相应图形,更加形象地显现出了各个路段的最优作业方案。     

Tailoring soft magnetic properties of Fe-based amorphous alloys through C addition

It is known that developing Fe-based amorphous alloys with the saturation flux density(B_s) higher than 1.65 T is a major challenge.In present work,effects of C addition on magnetic properties of Fe-based amorphous alloys were systematically studied.It has been found that the addition of C can significantly increase the saturation flux density(B_s) and the magnetic flux density at 800 A/m(B_(800)) of the Fe-B-C-Si-P amorphous alloys.After the addition of C,the B_s of the amorphous alloys increase from 1.61 T(Fe_(83)B_(13)Si_3 P_1) to 1.65-1.71 T(Fe_(83)B_(13-x)C_xSi_3 P_1,x=1.5,2,3 and 4). The Fe_(83)B_(10)C_3 Si_3 P_1 amorphous alloy possesses excellent soft magnetic properties with high B_s of 1.71 T and low H_c of 1.5 A/m.It shows that density increase of the alloys and weakened metalloid-sp/metal-d bonding caused by C addition contribute to the increment of B_s.It suggests that the newly developed high-performance amorphous alloys possess great potential in application.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

非同分布φ混合序列加权和的强极限收敛性

利用φ混合序列矩不等式和截尾的处理方法,研究非同分布φ混合序列加权和强极限收敛性质的问题,得到了若干新结果,推广并改进了独立同分布情形下的相应结果.     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。