Acyl-chloride functionalized graphene oxide chemically grafted with hindered phenol and its application in anti-degradation of polypropylene

In this study,graphene oxide (GO) nanosheets were first functionalized by the acyl-chloride reaction and then reacted with hindered phenol (HP) to obtain HP grafted GO (GO-g-HP).The GO-g-HP prepared under the optimized condition exhibited a high efficiency against both thermal and photo oxidation of isotactic polypropylene (iPP).GO-g-HP exhibited a much better anti-aging efficiency than that of HP and GO used individually or that of their physical mixture.The outstanding anti-aging effect of GO-g-HP was attributed to the excellent synergistic effect produced between the chemically bonded GO and HP,which resulted in an improved oxygen barrier property of GO and excellent utilization of the free radical scavenging capability of GO and HP.Also,thanks to the grafting of HP on GO,the physical loss of HP,which was one of the main shortcomings for traditional small molecular antioxidants,was largely suppressed.It is expected that the GO-g-HP prepared can well meet the requirement of long-term applications of polymers in some harsh service conditions.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

金具零部件表面防腐蚀试验研究

随着经济的持续高速增长，各行业用电需求增大。在加快特高压骨干电网建设的同时，提高现有电网的输电能力、输电质量成为重中之重。金具是海上换流站的重要组成部分，海洋环境的特殊性，对金具提出了更高的耐腐蚀性能要求。为了探究海洋环境对金具的腐蚀性，选用ZL101A和ZL102两种典型的铝合金金具，采用5种辅助防腐蚀工艺获得5种耐腐蚀样本，并模拟海上工况对其分别进行盐雾腐蚀试验，得出最优防腐蚀工艺。研究表明：ZL101A和ZL102两种铝合金具有一定的耐腐蚀性能，ZL101A铝合金的耐腐蚀性能强于ZL102铝合金的；抛丸处理的防腐措施在ZL101A铝合金样本中的防腐蚀表现要强于ZL102铝合金样本的；阳极氧化在两种材质中防腐蚀表现均为优异，是最优异的防腐蚀工艺。     

基于WEB的在线答疑系统的设计与实现

根据登录者的身份，基于WWW技术的在线答疑系统设计为三大模块：学生模块、教师模块和系统管理员模块，它们可分别完成提问、回答和版务管理等功能．还探讨了系统主要的实现技术。     

关于三网合一技术

介绍了我国现阶段并存的三网(电信网、有线电视网和计算机互联网)的特点与现状，分析了三网在融合过程中需要解决的一些不可避免的问题，以及三网合一的技术基础和促进三网合一的有利因素，提出了三网合一是现代通信和计算机网络发展的必然趋势，以及在三网融合的过程中还将有一个相互渗透交叉、相互竞争、共存发展过程的观点。     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点     

具有sn-网的空间

证明了具有σ—点有限sn—网及σ—局部可数sn—网的空间可刻划为度量空间在某些确定映射下的象.     

基于事前分析方法的工作流过程模型的验证

工作流执行过程中经常会出现非正常终止的情况,对此,将事前分析方法应用于工作流过程模型的验证中,即在工作流过程实例化前进行模型的有效性分析和结构正确性验证。该方法对传统的有向网络图进行扩展并以此来描述工作流过程,确定模型的有效性;进一步将扩展有向网络图转换成工作流网模型,应用Petri网技术分析该模型的冲突结构,以确保工作流过程的逻辑合理性。     

NIPA类共聚温敏水凝胶中水的状态和耐热性

用N-异丙基丙烯酰胺（NIPA）与丙烯酸钠（SA）及甲基丙烯酸钠（SMA）共聚合成了两个系列的水凝胶，研究了共聚组成与水凝胶基本性质的关系，并用示差扫描量热法（DSC）和热失重法（TG）研究了此类水凝胶中水的状态和耐热性。