基于动作单元的机电产品故障溯源诊断方法

针对故障在复杂机电产品中传递发展的特点,提出了一种基于动作单元的机电产品故障溯源诊断方法.按照"功能-运动-动作"对整机功能进行结构化分解得到基本的动作单元,并分析动作单元之间的传递过程;在此基础上建立以动作单元和故障现象为节点的贝叶斯网络模型,利用贝叶斯网络的推理算法,计算各个节点的发生概率并追溯最大概率路径,实现动作层的故障动作单元诊断及故障动作单元传播过程诊断;利用故障图对动作单元内部的故障模式及其传递发展过程进行描述,找到引起动作单元故障的根本原因.通过对机电产品动作层和动作单元内部的诊断分析,实现故障现象到故障原因的溯源诊断.将所提出的溯源诊断方法应用到某企业数控转台故障诊断中,结果表明,从运动的角度进行故障溯源诊断,能够有效地诊断出故障动作单元及其传播过程并反映出动作单元内部元件故障的传递发展过程,便于找到导致故障的根本原因,提高了对机电产品故障诊断的效率.     

鞋涉水问题的多体动力学与 流-固耦合系统建模及仿真分析

工程应用问题分析常涉及多体动力学与流-固耦合联合仿真，行人在湿路行走时的鞋涉水问题正是此类问题之典型，多系统联合仿真建模及完整的鞋“涉水-出水”过程模拟分析，对工程应用中类似复杂耦合问题的仿真分析具有良好的参考价值. 本文基于Adams/View建立人体下肢多体动力学模型以模拟行人步态，将之作为鞋运动的边界条件；而后建立鞋涉水过程的流-固耦合模型，采用耦合欧拉-拉格朗日方法（CEL）以可视化的方式分析鞋详细的“涉水-出水”过程，确定整个过程可分为排水、推水、水膜生成、水膜破裂和完全出水5个阶段. 最后，对运动鞋、平底鞋进行涉水仿真，对比各个阶段的体积分数云图、水域速度云图和系统动能变化，采用涉水时间和消耗能量大小为涉水性能评价指标，发现平底鞋的涉水性能弱于运动鞋.     

GPS单频PPP电离层延迟改正模型探讨

针对电离层延迟会导致GPS单频精密单点定位精度严重缺失的情况,分别探讨了克罗布歇模型、格网模型和历元差分模型,并采用IGS跟踪站数据进行电离层延迟改正。同时根据改正后的单频精密单点定位精度,比较了这三种电离层延迟改正模型的改正效果。结果表明:历元差分模型的改正效果最好,其改正后单频精密单点定位精度可达到厘米级,能较好地符合实际应用要求。     

高原公路驾驶员心率变异性试验分析

为了揭示驾驶员在高原公路行车时的心率变异性的变化情况,寻求提高行车安全性的途径,利用生物反馈仪在高原公路上进行了实地行车测试。以频域指标LF/HF作为高原公路驾驶员心率变异性指标,在分析驾驶时间、海拔高度与驾驶员心率变异性指标之间关系的基础上,建立了相关模型。分析结果表明：驾驶员在高原公路行车时,心率变异性受到高原低氧环境和驾驶时间的双重影响;海拔越高,驾驶时间越长,驾驶员交感神经张力越大,使驾驶员疲劳程度增大,安全隐患增大。     

RSS拓补结构机座的动态优化

以燃气轮机透平端RSS(旋转对称支承板)机座为研究背景,通过用D’Alembert原理建立了RSS机座的拓补优化域和等价边界条件,从而实现了用均匀化方法的RSS机座拓扑结构优化,得到了旋转对称的弧形支承板拓扑结构的机座.然后,结合原来RSS机座的机构特征在ANSYS workbench中建立了RSS拓补结构光滑有限元模型,并进行了工作条件下的模态分析,以前三阶模态振型中轴承座的振型作为当量静载荷加载到原模型对比计算,验证边界条件的正确性.以RSS机座弧形支承板的四个关键尺寸为设计变量,以机座的变形量和应力为目标函数,进行了随频率变化的动态优化设计.通过优化改变了RSS拓补结构的动态特性,使固有频率远离了工作频率.     

Sperm viability in the reproductive tract of females in a population of Sceloporus mucronatus exhibiting asynchronous reproduction

Asynchronous reproduction is a common phenomenon in high-elevation populations of lizards from Central México. Sperm storage in the reproductive tract of females is the mechanism for making oocyte fertilization possible. Our study addresses questions related to functional oviductal sperm storage of females mating on different dates throughout the reproductive season. A population of Sceloporus mucronatus with copulation in the summer and ovulation in the fall was chosen for this experiment. Eleven females that copulated in the field during June and 13 females that copulated in captivity during August were maintained in the laboratory until parturition. The number of pregnant females and the litter sizes produced in each experimental group were indicative of the viability of the stored sperm. Sperm stored in the reproductive tract of females were able to fertilize eggs after 4 months. No significant differences were found in the number of pregnant females between the 2 experimental groups nor in the litter sizes that they produced. We found that the amount of time sperm were held in the female reproductive tract (ca. 3 months) had no effect on the capacity of sperm to fertilize eggs. Histological examination of 8 oviducts collected before the mating season eliminated the possibility of sperm storage from one year to the next. In this system, sperm retention could have evolved as a response mechanism to deal with the asynchrony between sexes in the reproductive cycles. However, we cannot rule out alternative hypotheses.     

Comparative stability analyses of traditional and selective room-and-pillar mining techniques for sub-horizontal tungsten veins

The stability and productivity concerning a modification on the traditional room and pillar for a new selective technique at the Portuguese Panasqueira Mine have been described. The traditional room-and-pillar stoping uses 5.0-m wide rooms with 3.0 m×3.0 m pillars, while the selective room-and-pillar mining technique consists in stoping with rooms of 4.0 m wide and pillars of 4 m×4 m with a subsequent selective cutting of the quartz veins at the mid pillar of approximately 0.5 m high, to obtain a pillar section with an area of 3.0 m×3.0 m. The stability and productivity analyses indicate that the selective technique obtains smaller average pillar safety factor, more rock mass displacement, more extraction and selectivity ratios, and ore grade improvement, compared with the traditional technique. These results show that the selective technique is also more convenient. This proposed selective room-and-pillar mining technique is applicable to any sub-horizontal narrow quartz veins with wolfram, gold, etc. such as the famous La Rinconada gold mine in the Peruvian Andes.     

钨合金精密磨削砂轮磨损及对表面质量的影响机制

为了满足钨合金零件的高精度和高完整性表面加工需求,实现钨合金磨削质量的控制和加工工艺的优化,通过分析砂轮磨粒种类和结合剂类型对砂轮磨损形式的关系,明确了超硬磨料砂轮在钨合金磨削加工中的优势.研究了磨粒粒度和磨削参数对钨合金磨削加工质量的影响规律,为制定合理的磨削工艺提供依据.通过磨削试验获得钨合金高精度和高完整性表面磨削加工工艺.研究结果表明,钨合金磨削过程中砂轮易磨损,超硬磨料砂轮更适合钨合金的磨削加工.金属结合剂金刚石砂轮在钨合金磨削加工的表面质量和加工精度方面表现出优越性.通过改进磨削参数,钨合金精密磨削后表面粗糙度可达18.9 nm,实现了镜面磨削效果.     

Mechanical,electrical, and thermal properties of the directionally solidified Bi-Zn-Al ternary eutectic alloy

A Bi-2.0Zn-0.2Al (wt%) ternary eutectic alloy was prepared using a vacuum melting furnace and a casting furnace. The samples were directionally solidified upwards at a constant growth rate (V = 18.4 μm/s) under different temperature gradients (G = 1.15–3.44 K/mm) and at a constant temperature gradient (G = 2.66 K/mm) under different growth rates (V = 8.3–500 μm/s) in a Bridgman-type directional solidification furnace. The dependence of microstructure parameter (λ) on the solidification parameters (G and V) and that of the microhardness (Hv) on the microstructure and solidification parameters were investigated. The resistivity (ρ) measurements of the studied alloy were performed using the standard four-point-probe method, and the temperature coefficient of resistivity (α) was calculated from the ρ-T curve. The enthalpy (ΔH) and the specific heat (C_p) values were determined by differential scanning calorimetry analysis. In addition, the thermal conductivities of samples, obtained using the Wiedemann-Franz and Smith-Palmer equations, were compared with the experimental results. The results revealed that, the thermal conductivity values obtained using the Wiedemann-Franz and Smith-Palmer equations for the Bi-2.0Zn-0.2Al (wt%) alloy are in the range of 5.2–6.5 W/Km and 15.2–16.4 W/Km, respectively.     

Tool life modeling for evaluating the effects of cutting speed and reinforcements on the machining of particle reinforced metal matrix composites

The wear of cutting tools in the machining of 2024Al alloy composites reinforced with Al₂O₃ particles using varying sizes and volume fractions of particles up to 23.3vol% was investigated by a turning process using coated carbide tools K10 and TP30 at different cutting speeds. Machining tests were performed with a plan of experiments based on the Taguchi method. The tool life model was developed in terms of cutting speed, size, and volume fraction of particles by multiple linear regressions. The analysis of variance (ANOVA) was also employed to carry out the effects of these parameters on the cutting tool life. The test results show that the tool life decreases with the increase of cutting speed for both cutting tools K10 and TP30, and the tool life of the K10 tool is significantly longer than that of the TP30 tool. For the tool life, cutting speed is found to be the most effective factor followed by particle content and particle size, respectively. The predicted tool life of cutting tools is found to be in very good agreement with the experimentally observed ones.