Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

海上电泵结蜡井热循环洗井工艺参数优化设计

为探索海上油田电泵举升结蜡井热循环洗井工艺井筒温度场分布规律，综合考虑潜油电机增温、电缆散热、热流体注入量、注入深度、注入温度、结蜡管段传热和海水空气导热的影响，基于热能守恒原理，建立了电泵井结蜡热循环洗井工艺井筒温度场计算模型，分析了热流体注入温度和注入量对混合产出流体的井筒温度分布的影响。研究结果表明，随着注入量的增加混合产出液沿程井筒温度增加，随着注入温度的增加混合产出液沿程井筒温度增加。该方法可有效指导现场措施工艺的实施，达到延长结蜡井的清蜡周期、延缓产液/产油量下降速度的目的。     

强化传热生物质燃料热风炉研究

研制出用于粮食及其它农副产品干燥的新型热风炉。此炉型采用生物质燃料洁净燃烧技术及高强化传热技术,具有低污染、高效率、长寿命等优点。     

合成N,N,N'''',N''''-四(2-甲酯基乙基)乙二胺的绿色工艺研究

为了解决合成聚酰胺-胺时回收液处理复杂、能耗大、并污染环境的问题,以合成N,N,N',N'-四(2-甲酯基乙基)乙二胺(TMCEDA)为研究对象,对不同真空度条件下的回收液进行了定性定量分析,在此基础上,采用分段减压蒸馏分离合成TMCEDA中的过量原料与溶剂,直接循环使用真空度在50 kPa-100 kPa的回收液的新工艺.应用气相色谱分析技术跟踪分析循环使用的回收液的成分,结果表明,经过40次循环使用的回收液,仍未见明显的杂质积累现象.该工艺对回收液的直接使用率高达98.0%,实现了TMCEDA的实验室绿色合成,可为其工业化生产提供参考.图7,表2,参11.     

热连轧精轧机组温度模型的改进

从实际生产数据入手,研究了温度模型设定精度的现状及设定精度与各影响因素之间的关系,同时还消化了原来的温度模型程序并将其移植到微机上.经大量的离线统计回归分析,提出了一个行之有效的温度模型改进方案.该改进方案的思路同样适合其他热轧生产线.     

冷热敷治疗踝关节损伤

本文通过冷热敷和功能锻炼治疗踝关节损伤的试验，表明冷热治疗踝关节韧带损伤时间短，疗效好，在运动实践中可提倡．     

玻璃器皿压机转位机构凸轮——槽轮机构的研究

论述了一种拨销回转半径可变的凸轮——槽轮机构。叙述了玻璃器皿压机转位机构的运动要求。研究了用这种机构驱动工作台间歇转动的设计方法。     

真空C-度规中的虚Weyl坐标

研究了在真空C-度规中扩大Weyl坐标及其覆盖的时空区域的可能性. 结果表明:Weyl坐标可以扩大到虚坐标区域,虚Weyl坐标区域覆盖了真空C-度规视界内部区域. 获得了Weyl坐标下真空C-度规完整的时空图.