模拟地热水环境中304不锈钢管材的结垢与腐蚀电化学行为

基于地热水输送过程中金属管道材料出现的腐蚀结垢问题,研究了模拟地热水(我国中部平原地热水的环境条件)中304不锈钢管材的结垢和电化学腐蚀行为. 结果表明,304不锈钢管在模拟地热水环境中的结垢过程分为结晶成核和晶核生长两个阶段,结晶成核阶段消耗结垢离子的速度比晶核生长阶段更快,304不锈钢管道表面结垢层的微观形貌为不规则的"稻草"状,地热水温度的变化促进了304不锈钢材料在模拟地热水中的点蚀敏感性,其表面钝化膜的保护性也随地热水温度的升高而降低.     

地热水温度变化对不锈钢管道腐蚀行为的影响

采用动电位极化和电化学阻抗谱的方法,探究温度变化对316L不锈钢电极在模拟地热水溶液中腐蚀行为的影响.结果表明,316L不锈钢电极在55～75℃测试区间内均出现结垢现象.不锈钢电极表面结垢时间随温度变化显著,表现为随着温度的升高成膜时间先增加后减小.电化学结果显示不锈钢电极在65℃下具有最小的腐蚀电流密度、最大的腐蚀电...     

2507双相不锈钢在SO2污染模拟海水中的腐蚀行为

采用开路电位、电化学阻抗谱(EIS)、Mott-Schottky曲线和浸泡腐蚀实验研究了2507双相不锈钢在含不同浓度(0,0.001和0.01 mol·L-1)NaHSO3模拟海水中的腐蚀行为.研究表明:开路电位随NaHSO3浓度的增加而负移,腐蚀倾向增大;电荷转移电阻Rt随浓度的增加而减小,耐蚀性降低;2507不锈钢的腐蚀形态为局部腐蚀,点蚀程度随浓度升高有所加剧,腐蚀速率随浓度的增加而增大;Mott-Schottky曲线和成膜后电化学阻抗谱测试表明,NaHSO3的加入增加了2507不锈钢表面钝化膜的点缺陷浓度,降低了钝化膜的稳定性,电荷转移阻力减小,腐蚀更容易发生.这可能归因于NaHSO3的加入增加了模拟海水的酸度,并随NaHSO3浓度的增加促进了不锈钢表面钝化膜的破坏.     

河南省东部平原地热水结垢与腐蚀评价及防护技术的研究

腐蚀与结垢是地热开发利用中普遍存在的问题.通过对河南省东部平原地热水的结垢与腐蚀趋势的评价,针对会发生腐蚀与结垢的各热储层地热水提出了相应的防护技术—选择不同供暖形式防腐与诱垢载体除垢.     

电沉积铅改性304不锈钢双极板在模拟PEMFC环境中的性能

为提高304不锈钢双极板的耐腐蚀性能,分别采用直流和脉冲电刷镀铅对其表面改性.采用电化学方法测定了改性前后304不锈钢在模拟PEMFC环境下的极化曲线,在扫描电镜 (SEM) 下观察了模拟腐蚀后的表面形貌,并用伏安法测量了改性前后304不锈钢的接触电阻.在模拟PEMFC环境中,改性后304不锈钢自腐蚀电流密度由10.83μA/cm2下降至6.18μA/cm2.经200h模拟腐蚀后,304不锈钢表面发生点蚀,而改性不锈钢板表面完整,未观察到明显腐蚀.改性后的接触电阻也有所降低.结果表明,电沉积铅能有效提高304不锈钢在模拟PEMFC环境中的耐腐蚀性能,可望满足PEMFC环境下长期耐腐蚀的要求.     

弱电场干预对地热水中CaCO3结垢过程及形态的影响

采用电化学阻抗法，探究了在外加弱电场干预情况下，地热水溶液中及金属表面的结垢过程变化。实验结果表明，外部电场的干预会有效降低金属表面的结垢程度，长时间维持金属自身的电化学特征。外部电场干预下，因表面结垢程度的减少腐蚀电位不断发生负移；同时，电场干预下液相成垢过程发生变化，CaCO₃产物提前进入稳定的方解石晶型，使得大量的垢产物在液相中完成生长，随液体流动带走，也会进一步减少析晶垢向金属表面迁移沉积的风险.     

304 L不锈钢焊缝在混凝土模拟孔隙液中的点蚀行为

采用动电位极化曲线、电化学阻抗谱、Mott-Schottky曲线等电化学方法研究了以308 L为焊丝的304 L不锈钢焊接接头在不同氯离子含量的混凝土模拟孔隙液中腐蚀行为和电化学规律。随Cl-增加,304 L不锈钢焊接接头的三个区域(母材、焊缝和热影响区)在混凝土模拟孔隙液中的自腐蚀电位、点蚀电位及电荷转移电阻降低,钝化膜中载流子密度和焊接接头的点蚀坑数量增加。在同浓度的腐蚀溶液中,308 L的焊缝区域耐蚀性最佳,热影响区次之,304 L基体表现出低的电荷转移电阻和高的掺杂浓度使得母材的耐蚀性最差。     

304不锈钢在模拟压水堆一回路水中高温电化学腐蚀行为

通过模拟压水堆一回路水环境,研究了氯离子浓度和溶解氧对304不锈钢高温电化学腐蚀行为的影响.动电位极化曲线结果表明,氯离子浓度主要影响高电位下的二次钝化效应,低电位下影响效果不明显,结合X射线光电子能谱对氧化膜元素成分的分析发现二次钝化效应与氧化膜中Fe/Cr元素含量比密切相关.电化学阻抗谱和扫描电镜结果表明,随着氯离子浓度增加,氧化膜阻抗逐渐降低,表面外层氧化物颗粒和间隙逐渐增大,耐腐蚀性能降低.随着溶解氧含量的升高,304自腐蚀电位逐渐升高,钝化电流密度降低,钝化区间缩小,表面氧化膜阻抗逐渐增加.     

氯离子对石油测井仪器用Cr13不锈钢点损伤行为的影响

采用高温高压模拟环境装置和实时动电位极化和交流阻抗技术对石油测井仪器用Cr13不锈钢在模拟井下不同氯离子环境中电极的腐蚀失重和电化学行为进行了研究.实验结果表明,当地层水或者钻井液中氯离子浓度较高时,Cr13不锈钢表面的点损伤难以避免;随着氯离子浓度的升高,Cr13的均匀腐蚀速率增大,试样表面点蚀坑增多;局部氯离子以FeCl2和FeCl3形式吸附是造成钝化膜损伤的主要原因.应尽量减少仪器在含氯离子环境中的停留时间或提高材料等级.     

静水压力对304不锈钢腐蚀行为的影响

利用自制的腐蚀实验高压釜模拟深海低温高压化学环境,研究静水压力对304不锈钢腐蚀行为影响机制.利用电化学工作站对腐蚀过程进行原位检测和加速实验,得到交流阻抗谱和动电位极化曲线,通过等效电路拟合和Tafel外推法对数据进行处理.分析了腐蚀发生的热力学倾向和动力学过程,讨论了钝化膜状态对腐蚀的影响.常压环境下,自腐蚀电位高,容抗弧半径较小.氧气等气体分子容易在304不锈钢表面吸附,增大腐蚀发生的热力学倾向.随着静水压力的增加,自腐蚀电位变化不大,压力变化不会导致钝化膜性质的改变.但腐蚀电流密度从3.838×10-8 A/cm2增加到1.197×10-7 A/cm2,容抗弧半径减小,金属/钝化膜/溶液之间电位差降低,钝化膜溶解速率大于生长速率,导致钝化膜厚度减小,使304不锈钢腐蚀加剧.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.     

Tracking data management using topology of moving object database system for moving object constrained trajectory in LBS application

Advances in wireless technologies and positioning technologies and spread of wireless devices, an interest in LBS (Location Based Service) is arising. To provide location based service, tracking data should have been stored in moving object database management system (called MODBMS) with proper policies and managed efficiently. So the methods which acquire the location information at regular time intervals then, store and manage have been studied. In this paper, we suggest tracking data management techniques using topology that is corresponding to the moving path of moving object. In our techniques, we update the MODBMS when moving object arrived at a street intersection or a curved road which is represented as the node in topology and predict the location at past and future with attribute of topology and linear function. In this technique, location data that are corresponding to the node in topology are stored, thus reduce the number of update and amount of data. Also in case predicting the location,because topology are used as well as existing location information, accuracy for prediction is increased than applying linear function or spline function.