十二烷基苯磺酸钠对氯化钙和水玻璃溶液的渗透性影响

采用下向渗透试验方法测定了在氯化钙和水玻璃溶液中添加十二烷基苯磺酸钠后溶液在粉尘介质中的渗透规律．测定结果表明,十二烷基苯磺酸钠能在不同程度上提高溶液的渗透能力和降低溶液的表面张力,对于质量分数为５％,１５％,２５％的ＣａＣｌ２溶液,十二烷基苯磺酸钠的适宜添加量分别为０．５％～０．６％,０．２％～０．５％,０．２％～０．４％,此时溶液的渗透能力比不加添加剂时可提高约１５％,１４％,２８％．对于质量分数为５％,１５％,２５％的Ｎａ２ＳｉＯ３·９Ｈ２Ｏ溶液,十二烷基苯磺酸钠的适宜添加量分别为０．２％～０．４％,０．３％～０．５％,０．３％～０．５％,此时溶液的渗透能力可提高１９％,２３％,１１％．该研究结果对有效利用氯化钙和水玻璃进行固土抑尘具有重要的意义．     

黑曲霉AJ1958菊粉酶的产生和性质

从菊芋根际土壤中分离出一株菊粉酶（ＩｎｕｌｉｎａｓｅＥ．Ｃ．３．２．１．７）产生菌，经物理和化学诱变得高酶活黑曲霉突变株ＡＪ１９５８．该菌株在培养基（０．０７ｇ／ｍＬ菊芋提取液１０００ｍＬ，豆饼粉５ｇ，麸皮５ｇ，ＫＣＩ０．７ｇ，ＦｅＳＯ４·７Ｈ２Ｏ０．０１ｇ，ＭｇＳＯ４·７Ｈ２Ｏ０．５ｇ，ＰＨ５．０）中，于３０℃振荡培养３ｄ，酶活力可达６４μｍｏｌ·ｍｉｎ－１．酶水解反应的最适ＰＨ为３．０～４．０，最适温度为６０℃，在ＰＨ２．５～５．５的范围内和７５℃以下较稳定．适宜条件下，１０ｈ内０．０５ｇ／ｍＬ的菊粉溶液中之底物几乎１００％被酶水解．产物糖中果糖质量分数为９３％，葡萄糖质量分数为５．６％．该突变株产生的菊粉酶具有较满意的水解性和热稳定性．     

卤化物与水玻璃复合物的抑尘性能

在恒温箱中测定了粉尘试样添加ＣａＣｌ２或ＭｇＣｌ２和水玻璃后的含水率与环境温度、湿度、有效抑尘时间等因素之间的关系．研究结果表明：（１）当环境温度低于３１℃，相对湿度高于６０％，粉尘试样中ＣａＣｌ２和水玻璃含量的质量分数分别达到２０％和１０％（ＭｇＣｌ２和水玻璃含量的质量分数为２３％和１１．５％）时，试样的含水率就能保持大于５％（质量分数）；（２）当环境温度低于４０℃，相对湿度高于５０％，粉尘试样中ＣａＣｌ２和水玻璃含量的质量分数分别达到２６％和１３％（ＭｇＣｌ２和水玻璃含量的质量分数为３０％和１５％）时，试样的含水率就能保持大于５％（质量分数）；（３）ＣａＣｌ２或ＭｇＣｌ２与水玻璃复合后，其粘尘功能进一步增强，而且其溶液的弱酸性得到进一步降低。     

均匀设计在肌苷发酵中的应用

采用均匀设计对肌苷工程菌枯草芽孢杆菌株Ｑ２９０１－４－３５（ＳＧｒ）的最佳发酵条件进行了研究。确定发酵培养基配方为（质量分数）葡萄糖１２％ ,药用酵母粉１．４％ ,硫酸铵１．３％ ,玉米浆０．５％ ,Ｎａ２ＨＰＯ４·１２Ｈ２Ｏ ０．５％ ,ＫＣｌ０．６％ ,ＭｇＳＯ４·７Ｈ２Ｏ ０．２２％ ,ＣａＣＯ３ ２．０％ ,尿素０．２％ （分消）ｐＨ７．０,在上述发酵培养基中发酵产苷达１５．２０ｇ／Ｌ,该菌株的产苷能力比在原发酵培养基中的产苷能力提高了１０％ 。从而证明均匀设计实验所给回归模型对发酵条件的选择具有重要的指导意义。     

常用化肥对长沙多索线虫生活力的影响

研究了五种氮肥对长沙多索线虫生活力的影响，结果表明，对成虫，ｗ（ＣＯ（ＮＨ２）２大于２．０％，ｗ（ＮＨ４ＮＯ３）大于１．０％ｗ（ＮＨ４）２ＳＯ４）大于０．２５％ｗ（ＮＨ４ＣＩ）大于０．５％时就有致死作用；而ｗ（ＮＨ４ＨＣＯ３）的致死作用更强，浓度大于０．１％时线虫死亡，对寄生前期幼虫，四种常用化肥的质量分数大于０．２％时致死或抑制其活力。     

离子交换色谱法纯化赤霉素A_3的研究

对离子交换色谱法纯化赤霉素Ａ３（ＧＡ３）的研究表明，用强碱阴离子交换树脂Ｄ２９０能很好地分离ＧＡ３及其杂质，采用粒径ｒ０＝０．４０ｍｍ的细粒树脂装柱，用ｐＨ＝３．５、ｌｍｏｌ／Ｌ的ＮａＣｌ溶液洗脱，洗脱空间流速为２％ｍｉｎ－１，负载质量分数约为４％时，ＧＡ３与杂质可获得较好的分离，富含ＧＡ３的流出液中ＧＡ３质量分数为９４％，收率为９６％。     

复合型纳滤膜的制备及表征

在聚砜基膜上用界面聚合法制备了两种复合型纳滤膜ＰＡ０１和ＰＡ０２。在０．３ＭＰａ下,ＰＡ０１膜对ＭｇＳＯ４溶液和ＦｅＣｌ３溶液的脱直 ９６．０％和７８．０％,水通量分别为８．５（Ｌ．ｍ＾－２．ｈ＾－１）和７．９（Ｌ．ｍ＾－２．ｈ＾－１）;ＰＡ０２膜对ＭｇＳＯ４ｉｐｗｋｉｙｗ （２．０ｇ．Ｌ＾－１）和ＣａＣｌ溶液（０．５ｇ．Ｌ＾－１）的脱盐率分别为９８．０％和８８．８％,水通量分别为１．０（Ｌ。ｍ＾     

五台型煤焦CO2催化气化的补偿效应

五台型煤焦用Ｎａ２ＣＯ３、Ｋ２ＣＯ３作催化剂在０．２ＭＰａ和１１２３～１２３３Ｋ温度下进行ＣＯ２气化试验，发现上述两催化剂量分别在９～２５Ｗｔ％、５～２０Ｗｔ％范围内均能明显提高气化速率，且Ｋ２ＣＯ３的催化活性高于Ｎａ２ＣＯ３。催化剂用量对动力学参数的影响说明，该催化气化反应体系存在补偿效应，其等动力学温度分别为１５６２Ｋ（Ｎａ２ＣＯ３）和１７３９Ｋ（Ｋ２ＣＯ３）．     

ACC氧化酶的测定方法

利用番木瓜ＣａｒｉｃａＰａｐａｙａＬ．果实为材料，研究了１－氨基环丙烷－１－羧酸（ＡＣＣ）氧化酶的体内和体外测定方法．在ＡＣＣ氧化酶的体外分析中，甘油体积分数为１０％～３０％时能稳定酶的活性；φ（ＣＯ２）为０．３％～２０％（反应体系气相中）和０．５～１２ｍｍｏｌ／ＬＡＣＣ提高酶的活性；较适宜的ｐＨ值为７．２．     

黄铜渗铝的研究

采用粉末渗镀法，研究了黄铜渗铝工艺。获得有效渗铝的工艺条件是：渗镀温度６００℃，渗镀时间３ｈ，渗剂组成是Ａｌ粉４０％、ＮＨ４Ｃｌ２％和Ａｌ２Ｏ３粉５８％。渗铝后的黄铜耐蚀性提高１．８倍，硬度增加２５．６％，渗层厚度为５０μｍ。通过Ｘ射线衍射分析等得出，黄铜渗铝层的结构由表面至基体是Ｃｕ（０．６１０８）Ａｌ（０．３８９２）→γ２－Ｃｕ９Ａｌ４→α－ＣｕＺｎ（含Ａｌ）→α－ＣｕＺｎ。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.     

Tracking data management using topology of moving object database system for moving object constrained trajectory in LBS application

Advances in wireless technologies and positioning technologies and spread of wireless devices, an interest in LBS (Location Based Service) is arising. To provide location based service, tracking data should have been stored in moving object database management system (called MODBMS) with proper policies and managed efficiently. So the methods which acquire the location information at regular time intervals then, store and manage have been studied. In this paper, we suggest tracking data management techniques using topology that is corresponding to the moving path of moving object. In our techniques, we update the MODBMS when moving object arrived at a street intersection or a curved road which is represented as the node in topology and predict the location at past and future with attribute of topology and linear function. In this technique, location data that are corresponding to the node in topology are stored, thus reduce the number of update and amount of data. Also in case predicting the location,because topology are used as well as existing location information, accuracy for prediction is increased than applying linear function or spline function.