烧结工艺对SiC-Y2O3-Al2O3液相烧结的影响

研究SiC-Al2O3-Y2O3体系在无压液相烧结过程中,不同的埋粉、烧结温度和保温时间对致密化过程的影响规律以及发生的主要物理化学变化.通过对烧结体失重率、线收缩率和密度的测量和断面形貌的观察发现,以BN为惰性埋粉时,烧结助剂挥发严重,密度低;以Y2O3为埋粉时,烧结过程中Y2O3从埋粉扩散进入坯体,造成烧结体质量增加,实际上未促进烧结;Al2O3和60%(β-SiC)-25%Al2O3-15%Y2O3埋粉有利于烧结,这是由于埋粉中Al2O3的含量较试样中的Al2O3含量高,具有较高的Al2O分压,能有效抑制烧结助剂的挥发.埋粉相同时,由于烧结和挥发的竞争,密度随烧结温度的升高或保温时间的增长先增加后降低.     

掺锆SnO2酒敏陶瓷的工艺探讨

通过传统电子瓷生产工艺，研究了掺ＺｒＯ２１％Ｗｔ时制备ＳｎＯ２的工艺控制过程，在得到最佳预烧温度和烧结温度的基础上，研究了预烧与烧结温度的互补性，使用埋粉烧结法，得到了对乙醇有较高灵敏度的ＳｎＯ２陶瓷体。根据阻温特性曲线给出了最佳乙醇探测温度。     

碳化硅、氧化锆增韧氧化铝复相陶瓷的研究

在纳米氧铝粉中加入碳化硅晶须和纳米氧化铝粉，通过烧结得到细晶的氧化铝基复相陶瓷，达到了提高氧化铝陶瓷断裂韧性的目的．研究了Ｎａｎｏ－Ａｌ２Ｏ３／ＳｉＣ（ｗ）、ＺｒＯ２复相陶瓷的烧结温度、晶粒尺寸、ＳｉＣ（ｗ）含量等对细晶Ａｌ２Ｏ３基复相陶瓷材料断裂韧性的影响．采用纳米Ａｌ２Ｏ３粉，可使烧结温度大幅度下降，在１６００℃即可得到致密的细晶陶瓷材料．ＳｉＣ（ｗ）质量分数ｗ为１８％时可以得到较高的断裂韧性值，ＫＩＣ＝６．９６ＭＰａ·ｍ１／２．晶须增韧的机理仍然是晶须的拔出和断裂．加入ＺｒＯ２后，利用ＺｒＯ２的相变增韧的效果，可以使Ａｌ２Ｏ３基陶瓷材料的断裂韧性进一步提高．     

Fe基－Al_2O_3复合材料的界面研究

将工业还原铁粉、Ａｌ２Ｏ３颗粒、炭粉及某种适量粘结剂，通过粉末冶金方法在高温下进行烧结，制备了Ａｌ２Ｏ３颗粒增强Ｆｅ基复合材料。用ＳＴＥＭ，ＴＥＭ及ＳＥＭ对界面结合机制进行了分析与研究。结果表明，烧结过程中在Ａｌ２Ｏ３颗粒与Ｆｅ基界面生成了中间相，使Ａｌ２Ｏ３与铁基有良好的结合强度，所制备的Ｆｅ基－Ａｌ２Ｏ３复合材料的硬度、耐磨性已超过相同含碳量的碳钢材料     

包覆法添加烧结助剂制备Al2O3／SiCp复相陶瓷

通过包覆的方法将烧结助剂Ｙ２Ｏ３均匀地加入到陶瓷粉体中,用无压烧结制备Ａｌ２Ｏ３－ＳｉＣｐ复相陶瓷材料。在Ａｌ２Ｏ３／ＳｉＣ混合粉体上覆一层Ｙ（ＯＨ）３后,素坏结构均匀,且有利于提高素坏致密性。在较佳条件下,材料的相对密度和强调分别达到９６．８％和３６４ＭＰａ。     

ZTM／SiCp陶瓷的微波烧结研究

用微波烧结成功ＺＴＭ／ＳｉＣｐ三相复合陶瓷,ＳｉＣ含量达到３０ｖｏｌ％．提出“热过冲自我抑制”的思想．利用Ａｌ２Ｏ３＋ＳｉＯ２→Ｍｕｌ反应在微波烧结ＺＴＭ／ＳｉＣｐ陶瓷中实现了“热过冲自我抑制”．提出临界电场强度Ｅ＊可作为判断是否会出现“热过冲”的判据．埋粉是调节微波场强的有效手段．ＳｉＣ在低含量范围内有促进烧结的作用．     

一项高科技成果迈出产业化第一步──年产200吨易烧结α－Al_2O_3超微粉投

一项高科技成果迈出产业化第一步──年产２００吨易烧结α－Ａｌ_２Ｏ_３超微粉投入批量生产１９９５年１２月８日，由重庆市科委组织的国家级重点产品“易烧结α－Ａｌ２Ｏ３超微粉”鉴定会在我校召开，年产２００吨易烧结α－Ａｌ２Ｏ３超微粉项目通过鉴定．至此，我校...     

Ti对Al2O3／Ni复合材料相界面润湿及力学性能的影响

以无压烧结方式制备了Ａｌ２Ｏ３／２０％Ｎｉ（Ｔｉ）（体积分数）复合材料．通过分析Ｔｉ元素的分布状态，研究了Ｔｉ添加剂对Ａｌ２Ｏ３／２０％Ｎｉ复合材料相界面润湿及力学性能的影响规律．结果表明，Ｔｉ元素集中分布在Ａｌ２Ｏ３／Ｎｉ相界面附近，并通过促进相界面润湿，强化相界面结合而显著改善复合材料的力学性能．实验成分范围内，随Ｔｉ含量增加，三点弯曲强度提高，而断裂韧性在３％Ｔｉ（质量百分数）时具有最大值，为６．２ＭＰａｍ１２．断口形貌分析表明，复合材料的增韧机理为桥接机理     

LiNbO_3陶瓷溅射靶材的制备工艺研究

采用改进的陶瓷烧结工艺，研究了用于射频磁控溅射工艺的大尺寸薄型ＬｉＮｂＯ３陶瓷靶材的烧结工艺，解决了烧结过程中Ｌｉ２Ｏ的外逸造成成分偏差和Ｌｉ２Ｏ含量偏低时不易得到致密陶瓷的问题，探讨了Ｌｉ２Ｏ在烧结过程中的作用，制备出了高强度的ＬｉＮｂＯ３＋Ｌｉ２Ｏ系列陶瓷靶材．     

稀土α′＋β′──sialon陶瓷烧结过程研究

本文用一个特殊膨胀仪对加稀土氧化物添加剂的α′＋β′──ｓｉａｌｏｎ陶瓷在高氮压烧结（ＧＰＳ）下的烧结行为进行了研究．结果表明，致密过程受添加剂种类和烧结温度的影响相当大，在１５００℃等温烧结时速度控制阶段为扩散阶段，且以Ｓｍ２Ｏ３为添加剂的陶瓷最易被致密．同时，对烧结中与烧结过程有关的显微结构特征亦进行了讨论．     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with