烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

不同硅饱和系数水榴石的碳酸化分解动力学

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method, which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method. In this study, the effect of the silica saturation coefficient (x) on the carbonation of hydrogarnet was investigated from the kinetic perspective. The results indicated that the carbonation of hydrogarnets with different x values (x = 0.27, 0.36, 0.70, and 0.73) underwent two stages with significantly different rates, and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3. The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol, respectively. Moreover, the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.     

一种超重力燃烧合成制备高性能高熵合金的新方法

A new method of high-gravity combustion synthesis (HGCS) followed by post-treatment (PT) is reported for preparing high-performance high-entropy alloys (HEAs), Cr_0.9FeNi_2.5V_0.2Al_0.5 alloy, whereby cheap thermite powder is used as the raw material. In this process, the HEA melt and the ceramic melt are rapidly formed by a strong exothermic combustion synthesis reaction and completely separated under a high-gravity field. Then, the master alloy is obtained after cooling. Subsequently, the master alloy is sequentially subjected to conventional vacuum arc melting (VAM), homogenization treatment, cold rolling, and annealing treatment to realize a tensile strength, yield strength, and elongation of 1250 MPa, 1075 MPa, and 2.9%, respectively. The present method is increasingly attractive due to its low cost of raw materials and the intermediate product obtained without high-temperature heating. Based on the calculation of phase separation kinetics in the high-temperature melt, it is expected that the final alloys with high performance can be prepared directly across master alloys with higher high-gravity coefficients.     

窄板坯结晶器内连铸工艺参数对钢液流场的影响

Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting (CC) molds with narrow widths for the production of automobile exposed panels. Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process. The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold. Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone. The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min?1 and casting speed of 1.7 m·min?1. Under the present experimental conditions, the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.     

电渣重熔脱硫技术研究进展

Electroslag remelting (ESR) gives a combination of liquid metal refining and solidification structure control. One of the typical aspects of liquid metal refining during ESR for the advanced steel and alloy production is desulfurization. It involves two patterns, i.e., slag–metal reaction and gas–slag reaction (gasifying desulfurization). In this paper, the advances in desulfurization practices of ESR are reviewed. The effects of processing parameters, including the initial sulfur level of consumable electrode, remelting atmosphere, deoxidation schemes of ESR, slag composition, melting rate, and electrical parameters on the desulfurization in ESR are assessed. The interrelation between desulfurization and sulfide inclusion evolution during ESR is discussed, and advancements in the production of sulfur-bearing steel at a high-sulfur level during ESR are described. The remaining challenges for future work are also proposed.     

利用皮秒激光烧蚀制备非球形铝纳米颗粒

We report the picosecond laser ablation of aluminum targets immersed in a polar organic liquid (chloroform, CHCl₃) with ~2 ps laser pulses at an input energy of ~350 μJ. The synthesized aluminum nanoparticles exhibited a surface plasmon resonance peak at ~340 nm. Scanning electron microscopy images of Al nanoparticles demonstrated the spherical morphology with an average size of (27 ± 3.6) nm. The formation of smaller spherical Al nanoparticles and the diminished growth could be from the formation of electric double layers on the Al nanoparticles. In addition to spherical aluminum nanoparticles, triangular/pentagonal/hexagonal nanoparticles were also observed in the colloidal solution. Field emission scanning electron microscopy images of ablated Al targets demonstrated laser induced periodic surface structures (LIPSSs), which were the high spatial frequency LIPSSs (HSF-LIPSSs) since their grating period was ~280 nm. Additionally, coarse structures with a period of ~700 nm were observed.     

关于农业区划地图集中的统一协调问题

图集的统一协调,对图集质量有很大影响。本文是作者在编制北京市农业区划地图集的实践基础上,根据地图信息传输论的观点,对农业区划地图集的统一协调的内容及方法进行了探讨。试图总结编制这类图集的统一协调模式,以供读者编图时参考。     

“真空的真空”的存在性问题

许多科学家包括诺贝尔奖获得者李政道教授都预言,真空是未来物理学的一个重要研究对象.十七世纪的伽利略时代人们曾讨论过"真空"是否存在的问题.当时的学术界分成两派,一派以帕斯卡为代表,认为真空存在,另一派以笛卡尔为代表,认为真空不存在,最后实验证明"真空存在派"正确.现代研究表明,真空并非一无所有,这样就产生了一个新的问题"排除了真空物质后的空间",即"真空的真空"是否存在.本文探讨了与"真真空"有关的问题,提出了一些观测实验方法,这些方法可以帮助我们最终解答"真真空"的存在性问题.     

民间法正义观的转型

研究了国家法的抽象正义观与民间法的情理正义观,认为西方国家法的抽象正义观与东方民间法的情理正义观存在实质的不同,原因在于思维方式、超验与经验传统、政治结构的差别。在现代法治理念下,传统民间法所代表的正义观将向混合正义观转型,西方法治所代表的国家法抽象正义观是其骨架。     

人-自观念演进的否定之否定

在人与自然界的关系的演进过程中,形成了与不同文明时期相适应的人-自观念。从＂天人合一＂到＂人定胜天＂再到＂和谐共生＂,这是人-自观念演进的肯定、否定、否定之否定的辩证发展过程,也是一个合乎规律的过程,它们都是时代的产物,都包含着不同程度的合理的因素,我们必须对它们进行具体的辩证的分析。     

老年人生活空间移动性影响要素研究进展

 老年人生活空间移动性是老年人在日常生活中能动生活状态的重要表征。在梳理老年人生活空间移动性相关概念、测度方法基础上，分析了物质环境要素和非物质环境要素对老年人生活空间移动性的影响；提炼出有效支持老年人生活空间移动性的中观环境规划、微观环境设计和政策文化扶助层面的策略；指出了老年人生活空间移动性的研究建议和发展方向。     

行政机关违法设定许可的法律责任探析

对于行政许可违法的法律责任问题，人们往往是从行政许可实施违法的角度进行研究，而对于设定违法及其责任追究的探讨却相对薄弱。然而。行政许可设定一旦违法，其对相对人和社会公共利益的损害将会更大，因此，对许可设定的违法及其责任问题进行研究，以避免违法行政行为的发生，促进政府依法行政，不仅必要而且是非常有意义的。     

曲面"侧"概念的"参照物"理解法

曲面“侧”是一个重要而难以理解的概念,本文对曲面“侧”概念的讲授方法进行了探讨,给出了曲面“侧”概念的“参照物”理解法,通过实践证明,效果良好。     

关于一维非自治时滞系统点态退化一例

给出了一维非自治时滞系统点态退化的一个例子,拓宽了该领域的研究。     

动量守恒定律和动量矩守恒定律的正确表述

现行力学教材和普通物理教材大都把动量守恒定律和动量矩守恒定律视为质点组动量定理和动量矩定理的推论，忽视了守恒星的本质意义，是不正确的．本文绘出正确表述．