TiO<Subscript>2</Subscript>@MgO core-shell film: Fabrication and application to dye-sensitized solar cells

In this study,TiO2@MgO core-shell film was obtained by using a simple chemical bath deposition method to coat a thin MgO film around TiO2 nanoparticles. The core-shell configuration was characterized by X-ray diffractometer (XRD),scanning elec-tron microscopy (SEM),energy dispersive X-ray spectroscopy (EDX),and high-resolution transmission electron microscopy (HRTEM). Lattice fringes were observed for the TiO2 particles,and the MgO shell showed an amorphous structure,revealing a clear distinction between the core and shell materials. Applying the core-shell film as photoanode to the dye-sensitized solar cells (DSSCs),it shows a superior performance compared to the pure TiO2 electrode. Under the illumination of simulated sunlight (75 mW-cm-2),the short circuit photocurrent (Jsc),the open circuit photovoltage (Voc),and the fill factor (fF) are 8.80 mA-cm-2,646 mV,and 0.69,respectively,and the conversion efficiency (η) in-creased by 21.8% (from 4.32% to 5.26%) when dipping for opti-mum condition.     

Preparation of Zn-doped TiO2 nanotubes electrode and its application in pentachlorophenol photoelectrocatalytic degradation

Zn-doped titanium oxide （TiO2） nanotubes electrode was prepared on a titanium plate by direct anodic oxidation and immersing method in sequence. Field emission scanning electron microscopy （FESEM） showed that the Zn-doped TiO2 nanotubes were well aligned and organized into high density uniform arrays with diameter ranging from 50 to 90 nm. The length and the thickness were about 200 and 15 nm respectively. TiO2 anatase phase was identified by X-ray diffraction （XRD）. X-ray photoelectronspectroscopy （XPS） indicated that Zn ions were mainly located on the surface of TiO2 nanotubes in form of ZnO clusters. Compared with TiO2 nanotubes electrode, about 20 nm red shift in the spectrum of UV-vis absorption was observed. The degradation of pentachlorophenol （PCP） in aqueous solution under the same condition （initial concentration of PCP： 20 mg/L; concentration of Na2SO4：0.01 mol/L and pH： 7.03） was carried out using Zn-doped TiO2 nanotubes electrode and TiO2 nanotubes electrode. The degradation rates of PCP using Zn-doped TiO2 nanotubes electrode were found to be twice and 5.8 times as high as that using TiO2 nanotubes electrode by UV radiation （400 μw/cm^2） and visible light radiation （4500 μw/cm^2）, respectively. 73.5% of PCP was removed using Zn-doped TiO2 nanotubes electrode against 45.5% removed using TiO2 nanotubes electrode in 120 min under UV radiation. While under visible light radiation, the degradation efficiency of PCP was 18.4% using Zn-doped TiO2 nanotubes electrode against 3.2% using TiO2 nanotubes electrode in 120 min. The optimum concentration of Zn doping was found to be 0.909%. The PCP degradation efficiencies of the 10 repeated experiments by Zn-doped TiO2 nanotubes electrode were rather stable with the deviation within 3.0%.     

Comparison between P25 and anatase-based TiO<Subscript>2</Subscript> quasi-solid state dye sensitized solar cells

Pure anatase TiO2 films have been made via hydration of titanium isopropoxide using a sol-gel tech-nique, while mixed TiO2 films which contained both anatase and rutile TiO2 were made from commercial P25 powder. Quasi-solid state dye-sensitized solar cells were fabricated with these two kinds of mesoporous films and a comparison study was carried out. The result showed that the open-circuit photovoltages （Voc） for both kinds of cells were essentially the same, whereas the short-circuit photo-currents （1sc） of the anatase-based cells were about 33% higher than that of the P25-based cells. The highest photocurrent intensity of the anatase-based cell was 6.12 mA/cm^2 and that of the P25-based cell was 4.60 mA/cm^2. Under an illumination with the light intensity of 30 mW/cm^2, the corresponding energy conversion efficiency was measured to be 7.07% and 6.89% for anatase-based cells and P25-based cells, respectively.     

Layered Fe（Ⅲ） doped TiO2 thin-film electrodes for the photoelectrocatalytic oxidation of glucose and potassium hydrogen phthalate

Four types of TiO 2 thin-film electrodes were fabricated from TiO 2 and Fe(III) doped TiO 2 sols using a layer-by-layer dip-coating technique. Electrodes fabricated were TF (pure TiO 2 surface, Fe(III)-TiO 2 bottom layer), FT (Fe(III)-TiO 2 surface, pure TiO 2 bottom layer), TT (both layers pure TiO 2 ) and FF (both layers Fe(III)-TiO 2 ). The photoelectrochemical behavior of these electrodes was characterized using linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and steady-state photocurrent measurements in aqueous 0.1 mol L –1 NaNO 3 containing varying concentrations of glucose or potassium hydrogen phthalate (KHP). EIS and LSV results revealed that exciton separation efficiency followed the sequence of TF﹥TT﹥FT > FF. Under a constant potential of +0.3 V, steady-state photocurrent profiles were recorded with varying organic compound concentrations. The TF electrode possessed the greatest photocatalytic capacity for oxidizing glucose and KHP, and possessed a KHP anti-poisoning effect. Enhanced photoelectrochemical performance of the TF electrode was attributed to effective exciton separation because of the layered TF structure.     

Dissolution of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript> inclusions in CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags at 1823 K

Al-Ti-O inclusions always clog submerged nozzles in Ti-bearing Al-killed steel. A typical synthesized Al₂TiO₅ inclusion was immersed in a CaO-SiO₂-Al₂O₃ molten slag for different durations at 1823 K. The Al₂TiO₅ dissolution paths and mechanism were revealed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Decreased amounts of Ti and Al and increased amounts of Si and Ca at the dissolution boundary prove that inclusion dissolution and slag penetration simultaneously occur. SiO₂ diffuses or penetrates the inclusion more quickly than CaO, as indicated by the w(CaO)/w(SiO₂) value in the reaction region. A liquid product (containing 0.7–1.2 w(CaO)/w(SiO₂), 15wt%–20wt% Al₂O₃, and 5wt%–15wt% TiO₂) forms on the inclusion surface when Al₂TiO₅ is dissolved in the slag. Al₂TiO₅ initially dissolves faster than the diffusion rate of the liquid product toward the bulk slag. With increasing reaction time, the boundary reaches its largest distance, the Al₂TiO₅ dissolution rate equals the liquid product diffusion rate, and the dissolution process remains stable until the inclusion is completely dissolved.     

Synthesis and characterization of Pt-MoO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>-TiO<Subscript>2</Subscript> electrodes for direct ethanol fuel cells

To enhance the CO-tolerance performance of anode catalysts for direct ethanol fuel cells, carbon nanotubes were modified by titanium dioxide (donated as CNTs@TiO₂) and subsequently served as the support for the preparation of Pt/CNTs@TiO₂ and Pt-Mo/CNTs@TiO₂ electrocatalysts via a UV-photoreduction method. The physicochemical characterizations of the catalysts were carried out by using X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and infrared spectroscopy of adsorbed probe ammonia molecules. The electrocatalytic properties of the catalysts for methanol oxidation were investigated by the cyclic voltammetry technique. The results show that Pt-Mo/CNTs@TiO₂ electrode exhibits the highest performance in all the electrodes. It is explained that, the structure, the oxidation states, and the acid-base properties of the catalysts are influenced due to the strong interaction between Ti and Mo species by adding TiO₂ and MoO _x to the Pt-based catalysts.     

ZnO microsheet modified TiO<Subscript>2</Subscript> nanoparticle composite films for dye-sensitized solar cells

Randomly oriented ZnO microsheets were successfully self-assembled on TiO₂ nanoparticle (TN) film to act as the scattering layer via a cathodic electrodeposition process. The light scattering properties of ZnO microsheets were studied by UV-Vis spectrometer in the 400–800 nm wavelength range. It was found that ZnO microsheets exhibited excellent ability to scatter the incident light for ZnO microsheet-TiO₂ nanoparticle (ZT) composite films. The results showed that dye-sensitized solar cells (DSSCs) fabricated with ZT composite films showed higher short-circuit density (J_sc) and conversion efficiency than TN-based DSSCs, due to the light scattering properties of ZnO microsheets.     

Microwave sintering of Ca<Subscript>0.6</Subscript>La<Subscript>0.2667</Subscript>TiO<Subscript>3</Subscript> microwave dielectric ceramics

Ca_0.6La_0.2667TiO₃ ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Densified Ca_0.6La_0.2667TiO₃ ceramics were obtained by microwave sintering at 1350°C for 30 min and by conventional sintering at 1450°C for 4 h. An unusual phenomenon was found that some larger grains (grain size range: 8–10 μm) inclined to assemble in one area but some smaller ones (grain size range: 2–4 μm) inclined to gather in another area in the microwave sintered ceramics. The microwave dielectric properties of Ca_0.6La_0.2667TiO₃ ceramics prepared by microwave sintering at 1350°C were as follows: dielectric constant (ɛ _r) = 119.6, quality factor (Qf) = 17858.5 GHz, and temperature coefficient of resonant frequency (τ _f) = 155.5 ppm/°C. In contrast, the microwave dielectric properties of the ceramics prepared by conventional sintering at 1450°C were ɛ _r = 117.4, Qf = 13375 GHz, and τ _f = 217.2 ppm/°C.     

Performances improvement of eosin Y sensitized solar cells by modifying TiO2 electrode with silane-coupling reagent

Chemical fixing of xanthene dye （eosin Y） on the surface of TiO2 electrode was carried out by modifying the electrode with silane-coupling reagent to obtain stable dye-sensitized TiO2 electrode. Such silane modification can not only evidently enhance the stability of dye-sensitized TiO2 electrode but also improve the energy conversion efficiency of the assembled cells by increasing short-circuit photocurrent （Jsc） and open-circuit photovoltage （Voc）. It was found that the improvements of cell performances differ depending on the composition of the electrolyte. The optimum cell of the cell performance was achieved in the electrolyte with 0.5 mol/L TBAI/0.05 mol/L 12/EC：PC（3：1 w/w）, yielding Jsc of 4.69 mA. cm-2, Voc of 0,595 V, fill factor （FF） of 0.64 and ηof 1,78%, Different spectroscopic techniques including UV-Vis spectra, fluorescence spectra, EIS and dark current measurements were employed to derive reasonable analysis and explanations.     

Graded bandgap semiconductor thin film photoelectrodes

A graded bandgap oxide semiconductor thin film electrode was designed in order to obtain a photoelec-trochemically stable photoelectrode, with wide absorption range. The graded bandgap Ti_1−x V _x O₂ film electrode was prepared by heating the stacked layers of V/Ti in varying ratios, which were coated on the substrate by the sol-gel method using the starting solution with various V/Ti ratios. XPS result showed that the composition gradient was achieved for the film. The Ti_1−x V _x O₂ film electrode was found to be photoelectrochemically stable. Its photovoltage was about 360 mV. Obvious visible light photoresponse was observed for the Ti_1−x V _x O₂ film electrode. Compared with the pure TiO₂ electrode, the photocurrent onset potential of the Ti_1−x V _x O₂ film electrode was shifted positively, probably because the accumulation of vanadium at the electrode surface causes the recombination of the electrons and holes, and the lowest level of the conduction band of Ti_1−x V _x O₂ is lower than that of TiO₂. Impedance analysis showed that the donor density of the Ti_1−x V₂O₂ film electrode was higher than that of TiO₂ film electrode.     

An electrochemical impedance spectroscopic study of the electronic and ionic transport properties of LiCoO2 cathode

The storage behavior and process of the first delithiation-lithiation of LiCoO2 cathode were investigated by electrochemical impedance spectroscopy(EIS). The electronic and ionic transport properties of LiCoO2 cathode along with variation of electrode potential were obtained in 1 mol·L?1 LiPF6-EC:DMC:DEC electrolyte solution. It was found that after 9 h storage of the LiCoO2 cathode in electrolyte solu-tions,a new arc appears in the medium frequency range in Nyquist plots of EIS,which increases with increasing the storage time. In the charge/discharge processes,the diameter of the new arc is reversi-bly changed with electrode potential. Such variation coincides well with the electrode potential de-pendence of electronic conductivity of the LiCoO2. Thus this new EIS feature is attributed to the change of electronic conductivity of LixCoO2 during storage of the LiCoO2 cathode in electrolyte solutions,as well as in processes of intercalation-deintercalationtion of lithium ions. It has been revealed that the reversible increase and decrease of the resistance of SEI film in charge-discharge processes can be also ascribed to the variation of electronic conductance of active materials of the LiCoO2 cathode.     

Structure and photocatalytic properties of TiO<Subscript>2</Subscript>-Graphene Oxide intercalated composite

TiO2-Graphene Oxide intercalated composite (TiO2-Graphene Oxide) has been successfully prepared at low temperature (80°C) with graphite oxide (GO) and titanium sulfate (Ti(SO4)2) as initial reactants.GO was firstly exfoliated by NaOH and formed single and multi-layered graphite oxide mixture which can be defined as graphene oxide,[TiO]2+ induced by the hydrolysis of Ti(SO4)2 diffused into graphene oxide interlayer by electrostatic attraction.The nucleation and growth of TiO2 crystallites took place at low temperature and TiO2-Graphene Oxide composite was successfully synthesized.Furthermore,the photocatalytic properties of TiO2-Graphene Oxide under the irradiation of UV light were also studied.The results show that the degradation rate of methyl orange is 1.16 mg min-1 g-1(refer to the efficiency of the initial 15 min).Compared with P25 powder,this kind of intercalation composite owns much better efficiency.On the other hand,the reusable properties and stable properties of TiO2-Graphene Oxide intercalated composite are also discussed in this paper.At last,crystalline structure,interface status,thermal properties and microscopic structure of TiO2-Graphene Oxide were characterized by X-ray diffraction (XRD),X-ray photoelectron spectroscopy (XPS),thermogravimetric analysis (TGA),field emission scanning electron microscopy (FESEM) and high-resolution Transmission Electron Microscopy (HRTEM).Also,we have analyzed major influencing factors and mechanism of the composite structures which evidently improve the photocatalytic properties.     

High conversion efficiency of pristine TiO<Subscript>2</Subscript> nanotube arrays based dye-sensitized solar cells

We prepared highly-ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F-containing electrolytes.The crystalline nature and morphology of the TNAs were studied using X-ray diffraction patterns and scanning electron microscopy.We found the morphology of TNAs affects the light-to-electricity conversion efficiency (η) of dye-sensitized solar cells (DSSCs).The efficiency of DSSCs reached 5.95% under the condition of light illuminated from the counter electrode.The high efficiency of TNA-based DSSCs was attributed to the neat top surface of TNAs,which allows more dye molecule loading on the surface of the TiO 2 nanotubes,and fewer electron recombination centers and a low interface resistance of integrated TNAs.     

Preparation of nano-crystal N-Zn/TiO<Subscript>2</Subscript> anode films and the effects of co-sensitization on the performance of dye-sensitized solar cells

A nano-crystal N-Zn/TiO₂ anode film was prepared using a combined technology. X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy and cyclic voltammetry characterizations showed that the two elements N and Zn were doped into nano-crystal TiO₂ successfully. This resulted in a strong redshift in the UV-Visible spectrum. UV-Visible measurements showed that the light absorption of N719 and P3OT were complementary and covered the entire visible region. This led to a high utilization of visible light. Solar cells based on the N-Zn/TiO₂ anode film were co-sensitized using P3OT and N719. The cells have a short-circuit current density of 7.91 mA/cm², an open-circuit photovoltage of 0.659 V, and a photoelectric conversion efficiency of 2.64%. Also, the relationship among the N-Zn/TiO₂-film anode’s electric structure, the dye’s LUMO, electrochemical impedance, and photoelectric conversion efficiency are discussed in the paper.     

Electro-deoxidation of V<Subscript>2</Subscript>O<Subscript>3</Subscript> in molten CaCl<Subscript>2</Subscript>-NaCl-CaO

The electro-deoxidation of V₂O₃ precursors was studied. Experiments were carried out with a two-terminal electrochemical cell, which was comprised of a molten electrolyte of CaCl₂ and NaCl with additions of CaO, a cathode of compact V₂O₃, and a graphite anode under the potential of 3.0 V at 1173 K. The phase constitution and composition as well as the morphology of the samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). 3 g of V₂O₃ could be converted to vanadium metal powder within the processing time of 8 h. The kinetic pathway was investigated by analyzing the product phase in samples prepared at different reduction stages. CaO added in the reduction path of V₂O₃ formed the intermediate product CaV₂O₄.     

Visible light photocatalytic decoloration of methylene blue on novel N-doped TiO2

Novel N-doped TiO2 (denoted as N-NTA600) was prepared by treating nanotube titanic acid (NTA) in NH3 flow. Its visible light photocatalytic activity,evaluated by decoloration reaction of methylene blue,is higher than that of N-P25(600) prepared by treatment of P25-TiO2 in the same condition. It is suggested that the origin of visible-light photocatalytic activity is single-electron-trapped oxygen vacancy (Vo·) modified by chemisorbed NO.     

Catalysis of organic pollutant photodegradation by metal phthalocyanines immobilized on TiO<Subscript>2</Subscript>@SiO<Subscript>2</Subscript>

A TiO2@SiO2 hybrid support was prepared by the sol-precipitation method using n-octylamine as a template.The photocatalyst manganese phthalocyanine tetrasulfonic acid (MnPcS) was immobilized on the support to form MnPcS-TiO2@SiO2.X-ray diffraction (XRD) and UV-Visible diffuse reflectance spectra (UV-Vis DRS) were employed to characterize the catalyst.The photocatalytic degradation of rhodamine B (RhB) and the catalytic oxidation of o-phenylenediamine (OPDA) under visible light irradiation were used as probe reactions.The mineralization efficiency and the degradation mechanism were evaluated using chemical oxygen demand (COD Cr) assays and electron spin resonance (ESR),respectively.RhB was efficiently degraded by immobilized MnPcS-TiO2@SiO2 under visible light irradiation.Complete decolorization of RhB occurred after 240 min of irradiation and 64.02% COD Cr removal occurred after 24 h of irradiation.ESR results indicated that the oxidation process was dominated by the hydroxyl radical (·OH) and superoxide radical (O-·2) generated in the system.     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

Synthesis and Structure of Polypyrrole Derivatives／V2O5 Nanocomposites

Poly ( N, N, N-trimethyl ( 2-pyrrol-l-yl ) ethyl ammonium iodide )/V2O5 ( PTPAI/V2O5) nanocomposites were synthesized by sol-gel method. This method involved formation of vanadium pentoxide xerogel in the prcscnce of polypyrrole derivatives solution. X-ray diffraction(XRD) indicated that the polypyrrole derivative particles encapsulated in the fibrous V2O5 network and the layered distance significantly increased from 1. 077 39 to 1. 354 56 nm. The interaction between polypyrrole and V2O5 in the ‘nanocomposites‘ was characterized by IR spectroscopy. The Scanning Electron Microscope(SEM) micrographs reveal the structural contrasts between the hybrid materials and the pristine vanadium oxide xerogel.     

Fluorescence and sensitization performance of phenylene-vinylene-substituted polythiophene

A new kind of polythiophene derivative, Poly(3-{2-[4-(2-ethylhexyloxy)-phenyl]-vinyl}-2,2′-bithiophene) (PTh), was applied in dye-sensitized solar cell to extend the light response of nanocrystalline TiO2 electrode. UV-vis absorption and fluorescence spectra were employed to investigate the interaction of PTh with nanocrystalline TiO2. The absorption coefficient of the PTh was high in visible part of spec- trum, and the fluorescence emission of the PTh can be efficiently quenched by TiO2 nanoparticles ow- i...