Chemical quenching and inhibition of positronium in Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The pore structure of Cr2O3/Al2O3 catalysts and the surface chemical properties of these pores were characterized by positron lifetime and coincidence Doppler broadening (CDB) measurements. Four lifetime components could be resolved from the positron lifetime spectrum, with two long lifetime components and two short lifetime components. The two long lifetimes τ4 and τ3 are attributed to ortho-positronium (o-Ps) annihilation in large pores and microvoids, respectively. With increasing Cr2O3 content, both τ4 and its intensity I4 show sharp decrease, while τ3 and its intensity I3 keep nearly unchanged. The Doppler broadening S parameters also show sharp decrease with increasing Cr2O3 content. Detailed analysis of the CDB spectrum reveals that the parapositronium (p-Ps) intensity also decreases with increasing Cr2O3 content. This indicates that the change of o-Ps lifetime τ4 is due to the chemical quenching by Cr2O3 but not spin-conversion of positronium. The decrease of o-Ps intensity I4 indicates that Cr2O3 also inhibits positronium formation.     

Preparation of Zn-doped TiO2 nanotubes electrode and its application in pentachlorophenol photoelectrocatalytic degradation

Zn-doped titanium oxide （TiO2） nanotubes electrode was prepared on a titanium plate by direct anodic oxidation and immersing method in sequence. Field emission scanning electron microscopy （FESEM） showed that the Zn-doped TiO2 nanotubes were well aligned and organized into high density uniform arrays with diameter ranging from 50 to 90 nm. The length and the thickness were about 200 and 15 nm respectively. TiO2 anatase phase was identified by X-ray diffraction （XRD）. X-ray photoelectronspectroscopy （XPS） indicated that Zn ions were mainly located on the surface of TiO2 nanotubes in form of ZnO clusters. Compared with TiO2 nanotubes electrode, about 20 nm red shift in the spectrum of UV-vis absorption was observed. The degradation of pentachlorophenol （PCP） in aqueous solution under the same condition （initial concentration of PCP： 20 mg/L; concentration of Na2SO4：0.01 mol/L and pH： 7.03） was carried out using Zn-doped TiO2 nanotubes electrode and TiO2 nanotubes electrode. The degradation rates of PCP using Zn-doped TiO2 nanotubes electrode were found to be twice and 5.8 times as high as that using TiO2 nanotubes electrode by UV radiation （400 μw/cm^2） and visible light radiation （4500 μw/cm^2）, respectively. 73.5% of PCP was removed using Zn-doped TiO2 nanotubes electrode against 45.5% removed using TiO2 nanotubes electrode in 120 min under UV radiation. While under visible light radiation, the degradation efficiency of PCP was 18.4% using Zn-doped TiO2 nanotubes electrode against 3.2% using TiO2 nanotubes electrode in 120 min. The optimum concentration of Zn doping was found to be 0.909%. The PCP degradation efficiencies of the 10 repeated experiments by Zn-doped TiO2 nanotubes electrode were rather stable with the deviation within 3.0%.     

Comparative study of oxidation ability between boron-doped diamond (BDD) and lead oxide (PbO<Subscript>2</Subscript>) electrodes

The electrochemical oxidation capabilities of two high-performance electrodes, the boron-doped diamond film on Ti (Ti/BDD) and the lead oxide film on Ti (Ti/PbO₂), were discussed. Hydroxyl radicals (·HO) generated on the electrode surface were detected by using p-nitrosodimethylaniline (RNO) as the trapping reagent. Electrochemical oxidation measurements, including the chemical oxygen demand (COD) removal and the current efficiency (CE), were carried out via the degradation of p-nitrophenol (PNP) under the galvanostatic condition. The results indicate that an indirect reaction, which is attributed to free hydroxyl radicals with high activation, conducts on the Ti/BDD electrode, while the absorbed hydroxyl radicals generated at the Ti/PbO₂ surface results in low degradation efficiency. Due to quick mineralization which combusts PNP to CO₂ and H₂O absolutely by the active hydroxyl radical directly, the CE obtained on the Ti/BDD electrode is much higher than that on the Ti/PbO₂ electrode, notwithstanding the number of hydroxyl radicals produced on PbO₂ is higher than that on the BDD surface.     

自由基抑制剂对不同晶型TiO2光催化反应的影响

以荧光光谱法研究了不同晶型 TiO₂ 的光催化反应体系中羟基自由基(·OH)的产生情况,表明在H₂O₂存在条件下,金红石型 TiO₂ 经可见光激发可持续稳定产生·OH,而以锐钛矿型 TiO₂ 作光催化剂时,则检测不到·OH的生成。光催化结果表明,在H₂O₂存在条件下,苯酚可被 TiO₂ 可见光催化降解;往反应体系加入自由基抑制剂(叔丁醇或甲醇)时,明显降低了金红石型 TiO₂ 的降解效率,但对锐钛矿型 TiO₂ 的影响较弱。以金红石型 TiO₂ 作光催化剂时,苯酚的降解反应主要发生在溶液中;而以锐钛矿型 TiO₂ 作光催化剂时,则苯酚的降解反应主要发生在催化剂的表面。     

Synthesis, Characterization and Calorimetry of Ni（C4H8N2O3）2Cl2

A coordination complex was synthesized from NiCl2 and dipeptide glycylglycine（GG）. It was characterized by element analysis, NMR and TG methods, and then was determined to be Ni（C4HsN2O3）2Cl2. Using an isoperibolic reaction calorimeter, the standard molar enthalpy of formation of Ni（GG）2Cl2（solid） has been determined to be -（1 674.66±2.02） kJ · mol^-1 at 298.15 K.     

Effect of CO<Subscript>2</Subscript> concentrations on the activity of photosynthetic CO<Subscript>2</Subscript> fixation and extracelluar carbonic anhydrase in the marine diatom <Emphasis Type="Italic">Skeletonema costatum</Emphasis>

The growth and activity of photosynthetic CO2 uptake and extracellular carbonic anhydrase (CAext) of the marine diatom Skeletonema costatum were investigated while cultured at different levels of CO2 in order to see its physio-logical response to different CO2 concentrations under either a low (30 靘ol·m-2·s-1) or high (210 靘ol·m-2·s-1) irradiance. The changes in CO2 concentrations (4—31 靘ol/L) affected the growth and net photosynthesis to a greater extent under the low than under the high light re-gime. CAext was detected in the cells grown at 4 mol/L CO2 but not at 31 and 12 靘ol/L CO2, with its activity being about 2.5-fold higher at the high than at the low irradiance. Photo- synthetic CO2 affinity (1/ K1/2(CO2)) of the cells de-creased with increased CO2 concentrations in culture. The cells cultured under the high-light show significantly higher photosynthetic CO2 affinity than those grown at the low-light level. It is concluded that the regulations of CAext activity and photosynthetic CO2 affinity are dependent not only on CO2 concentration but also on light availability, and that the de-velopment of higher CAext activity and CO2 affinity under higher light level could sufficiently support the photosyn-thetic demand for CO2 even at low level of CO2.     

Preparation and photocatalytic properties of ilmenite NiTiO<Subscript>3</Subscript> powders for degradation of humic acid in water

The powders of ilmenite structure NiTiO₃ were prepared by a modified Pechini process using tetrabutyl titanate and nickel acetate as raw materials, and using citric acid and ethanol as a chelating agent and a solvent respectively. The powder samples were characterized by thermogravimetric and differential thermal analysis (TG-DTA) and X-ray diffraction (XRD). The photocatalytic activity of NiTiO₃ under the irradiation of ultraviolet rays (UV) light was evaluated by degrading humic acid (HA) in water as a probe reaction. The possible photodegradation mechanism was studied by the examination of active species ·OH, ·O₂⁻, and holes (h⁺) through adding scavengers. The TG-DTA and XRD results indicated that the good crystal structure of ilmenite phase NiTiO₃ could be obtained when the Ni-Ti citrate complex was calcined at 600°C. The photocatalytic activity experiments indicated that NiTiO₃ had favourable photocatalytic activity under the irradiation of UV light, and the photocatalytic degradation rate of HA reached 95.3% after a 2.5 h reaction with the photocatalyst calcined at 600°C and a photocatalyst dosage of 0.4 g/L. The possible photocatalytic mechanism was deduced that holes (h⁺) and ·OH radicals are the major reactive active species in the photocatalytic reaction, and dissolved oxygen plays a weak role in the degradation of HA.     

Investigation of the cross-reaction mechanism of C<Subscript>6</Subscript>H<Subscript>5</Subscript>F-HNO<Subscript>2</Subscript> aqueous solution irradiated at 355 nm by transient absorbance spectrum technique

The transient absorption spectrum technique was employed to investigate the cross-reaction mechanism of C6H5F-HNO2 aqueous solution irradiated at 355 nm. The characteristic and the kinetic parameters of transient species were also detected. Hydroxyl radical derived from the photolysis of HNO2 was added to monofluorobenzene with a second-order rate constant of （5.83±0.17）×10^9 L·mol^-1·s^-1 to form an adduct, C6H5F…OH, which was able to react with HNO2 as the main reaction pathway with a rate constant of （8.3±0.1）×10^7 L·mol^-1·s^-1. The C6F6…OH adduct can also be decayed by elimination of H2O to yield monofluorophenyl radical C6H4F-. By GC-MS technique, the final products were identified to be monofluorophenol, nitro-monofluorobenzene, nitro-monofluorophenol and para-fluorobiphenyl.     

Visible light photocatalytic decoloration of methylene blue on novel N-doped TiO2

Novel N-doped TiO2 (denoted as N-NTA600) was prepared by treating nanotube titanic acid (NTA) in NH3 flow. Its visible light photocatalytic activity,evaluated by decoloration reaction of methylene blue,is higher than that of N-P25(600) prepared by treatment of P25-TiO2 in the same condition. It is suggested that the origin of visible-light photocatalytic activity is single-electron-trapped oxygen vacancy (Vo·) modified by chemisorbed NO.     

Ionization and dissociation of CH<Subscript>2</Subscript>I<Subscript>2</Subscript> and CH<Subscript>2</Subscript>ICl in femtosecond intense field

With the development of ultrafast laser technique,the femtosecond laser electric field is comparable to themolecular field experienced by valence electrons. In thiscase, the classical quantum mechanical theory, based onperturbation theory, becomes inapplicable. Theoreticalunderstanding of the interaction of molecules with intenselaser radiation is quite difficult. The Coulomb explosionhas been extensively studied[1—10] and explained by somesemiclassical models, such as the above threshold ion…     

The giant magnetocaloric effect in Gd<Subscript>5</Subscript>Si<Subscript>2</Subscript>Ge<Subscript>2</Subscript> with low purity gadolinium

The giant magnetocaloric effect Gd5Si2Ge2 alloy was prepared with 99wt% low purity commercial Gd. Powder XRD and magnetic measurements showed that the Gd5Si2Ge2 alloy annealed at 1200℃ for 1h had a significant magnetic- crystallographic first order phase transition at about 270 K. The maximal magnetic entropy change is 17.55 J· kg^-1· K^-1 under a magnetic field change of 0-5 T. The distinct increase of magnetic entropy change belongs to the first-order phase transition from the orthorhombic Gd5Si4-type to the monoclinic Gd5Si2Ge2-type after high temperature heat-treatment.     

二氧化钛-硫化镉/氧化石墨烯复合材料光催化降解废水中有机物的研究

本论文采用溶剂热法制备出TiO₂-CdS/rGO三元复合光催化材料,并对其降解亚甲基蓝、罗丹明B的光催化活性进行研究,发现TiO₂-CdS/rGO对于亚甲基蓝、罗丹明B的光催化降解活性优于TiO₂-CdS,催化效率明显提高,降解时间大大缩短;在可见光照射下,以TiO₂-CdS/rGO为光催化剂,光反应时间40 min,亚甲基蓝、罗丹明B的降解率可达100%。本文还研究了催化材料的稳定性、催化剂用量对光催化降解效果的影响。     

Photocatalytic degradation of metronidazole in aqueous solution by niobate K<Subscript>6</Subscript>Nb<Subscript>10.8</Subscript>O<Subscript>30</Subscript>

The photocatalytic degradation of antibiotic metroni-dazole in aqueous solution by niobate K6Nb10.8O30 photocatalyst that was prepared using a soft-chemical method was studied by Fourier transform infrared spectroscopy and UV-Vis absorption spectrum. Metronidazole is very stable and is difficult to degrade under UV irradiation. K6Nb10.8O30 photocatalyst cannot degrade metronidazole without UV irradiation and shows very high photo-catalytic activity for the degradation of metronidazole under UV irradiation. The photocatalytic degradation rate of metronidazole increased with increasing the dosage of K6Nb10.8O30 photocatalyst. The photocatalytic degradation reaction of metronidazole by nio-bate K6Nb10.8O30 follows the first-order kinetic equation.     

Microstructure and Corrosion Resistance of Cr7C3/γ-Fe Ceramal Composite Coating Fabricated by Plasma Cladding

A new type in situ Cr7C3/γ-Fe ceramal composite coating was fabricated on substrate of hardened and tempered grade C steel by plasma cladding with Fe-Cr-C alloy powders. The ceramal composite coating has a rapidly solidified microstructure consisting of primary Cr7C3/γ- and the Cr7C3/γ-Fe eutectics, and is metallurgically bonded to the degree C steel substrate. The corrosion resistances of the coating in water solutions of 0.5 mol/L H2SO4 and 3.5% NaCl were evaluated utilizing the electrochemical polarization corrosion-test method. Because of the inherent excellent corrosion-resisting properties of the constituting phase and the rapidly solidified homogeneous microstructure, the plasma clad ceramal composite coating exhibits excellent corrosion resistance in the water solutions of 0.5 mol/L H2SO4 and 3.5% NaCl.     

Mechanism of photocatalytic degradation of dye MG by TiO<Subscript>2</Subscript>-film electrode with cathodic bias potential

Photoelectrocatalytic degradation of malachite green (MG) under visible light irradiation with TiO2-film electrode has been investigated to reveal the mechanism for TiO2 photocatalytic degradation of dyes. The supported TiO2 electrode was prepared in laboratory and detected by scanning electron micros-copy and X-ray diffractometry. We have examined the degradation kinetics, change in degradation rate of MG and photocurrent change with the bias potential, voltage-induced adsorption of dyes, accumu-lation of ...     

Preparation and characterization of γ-La<Subscript>2</Subscript>S<Subscript>3</Subscript> nanoparticles from thermal decomposition

To synthesize pure γ-La₂S₃ at lower temperature, lanthanide complex La(Et₂S₂CN)₃·phen, containing La-S bond, was chosen as the precursors to decompose. The obtained samples were characterized by X-ray power diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) with an energy dispersive spectrometer and UV-Vis diffuse reflectance spectra. The decomposition mechanism of the lanthanide complex was studied by thermogravimetric analyses (TGA). The results show that the obtained samples are cubic phase particles with sizes among 20–50 nm and the band gap is 2.97 eV, which is bigger than that of its bulk crystal. TG/DTG results indicate that La(Et₂S₂CN)₃·phen decomposed to γ-La₂S₃ via La₄(Et₂S₂CN)₃ as an intermediate product.     

Electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.3</Subscript>Ti<Subscript>0.2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> cells

Spinel compounds LiNi_0.5Mn_1.3Ti_0.2O₄ (LNMTO) and Li₄Ti₅O₁₂ (LTO) were synthesized by different methods. The particle sizes of LNMTO and LTO are 0.5–2 and 0.5–0.8 μm, respectively. The LNMTO/LTO cell exhibits better electrochemical properties at both a low current rate of 0.2C and a high current rate of 1C. When the specific capacity was determined based on the mass of the LNMTO cathode, the LNMTO/LTO cell delivered 137 mA·h·g⁻¹ at 0.2C and 118.2 mA·h·g⁻¹ at 1C, and the corresponding capacity retentions after 30 cycles are 88.5% and 92.4%, respectively.     

A review of TiO<Subscript>2</Subscript> nanoparticles

Climate change and the consumption of non-renewable resources are considered as the greatest problems facing humankind.Because of this,photocatalysis research has been rapidly expanding.TiO2 nanoparticles have been extensively investigated for photocatalytic applications including the decomposition of organic compounds and production of H2 as a fuel using solar energy. This article reviews the structure and electronic properties of TiO2,compares TiO2 with other common semiconductors used for photocatalytic applications and clarifies the advantages of using TiO2 nanoparticles.TiO2 is considered close to an ideal semi- conductor for photocatalysis but possesses certain limitations such as poor absorption of visible radiation and rapid recombination of photogenerated electron/hole pairs.In this review article,various methods used to enhance the photocatalytic characteristics of TiO2 including dye sensitization,doping,coupling and capping are discussed.Environmental and energy applications of TiO2, including photocatalytic treatment of wastewater,pesticide degradation and water splitting to produce hydrogen have been summarized.     

TiO<Subscript>2</Subscript>@MgO core-shell film: Fabrication and application to dye-sensitized solar cells

In this study,TiO2@MgO core-shell film was obtained by using a simple chemical bath deposition method to coat a thin MgO film around TiO2 nanoparticles. The core-shell configuration was characterized by X-ray diffractometer (XRD),scanning elec-tron microscopy (SEM),energy dispersive X-ray spectroscopy (EDX),and high-resolution transmission electron microscopy (HRTEM). Lattice fringes were observed for the TiO2 particles,and the MgO shell showed an amorphous structure,revealing a clear distinction between the core and shell materials. Applying the core-shell film as photoanode to the dye-sensitized solar cells (DSSCs),it shows a superior performance compared to the pure TiO2 electrode. Under the illumination of simulated sunlight (75 mW-cm-2),the short circuit photocurrent (Jsc),the open circuit photovoltage (Voc),and the fill factor (fF) are 8.80 mA-cm-2,646 mV,and 0.69,respectively,and the conversion efficiency (η) in-creased by 21.8% (from 4.32% to 5.26%) when dipping for opti-mum condition.     

Synthesis and Magnetic Properties of Spin-Liquid Tb2Ti2O7

Polycrystalline samples of a novel spin-liquid compound Tb2Ti2O7 were prepared by a standard solid-state reaction. X-ray diffraction at room temperature confirms that the synthesized compound of Tb2Ti2O7 is single phase with cubic unit cell constant a0 of 1.015 44 nm. Magnetic susceptibility measurements in the temperature range between 100 and 300 K give an effective moment of 9.44 μB and Curie-Weiss temperature of 12.68 K, respectively, indicating the dominance of antiferromagnetic interactions. However, below 50 K, the magnetic behavior of Tb2Ti2O7 deviates from Curie-Weiss law, whose origin remains suspicion.