聚L-苯丙氨酸修饰电极测定尿酸

用循环伏安法制备聚L-苯丙氨酸修饰玻碳电极,研究尿酸在聚L-苯丙氨酸修饰电极上的电化学行为,建立循环伏安法测定尿酸的新方法.在pH 4.0的磷酸盐缓冲溶液中,尿酸在聚L-苯丙氨酸修饰玻碳电极上出现一氧化峰,峰电位为Epa=+638 mV(相对于Ag/AgCl电极),氧化峰电流与尿酸浓度在5.00×10-7～5.00×10-5 mol/L范围内成线性关系,检测限:1.0×10 -7 mol/L.对1.0×10 -5 mol/L UA溶液平行测20次,其相对标准偏差为3.1%.用于尿液中尿酸的测定,结果满意.     

Rapid determination of carbendazim content in solution by differential pulse voitammetry

制备了纳米金-多壁碳纳米管复合物修饰电极,用循环伏安法研究了多菌灵在该修饰电极上的电化学行为.结果表明,多菌灵在1.08 V处出现了一个不可逆氧化峰,该氧化过程受扩散控制.在1.0×10-6 mol/L～1.0×10-4 mol/L范围内,脉冲伏安法的氧化峰电流与多菌灵浓度呈现良好的线性关系.该复合物修饰电极可快速、方便、灵敏地检测溶液中多菌灵含量.     

脉冲伏安法快速测定溶液中多菌灵含量

制备了纳米金-多壁碳纳米管复合物修饰电极,用循环伏安法研究了多菌灵在该修饰电极上的电化学行为.结果表明,多菌灵在1.08V处出现了一个不可逆氧化峰,该氧化过程受扩散控制.在1.0×10-6 mol/L～1.0×10-4 mol/L范围内,脉冲伏安法的氧化峰电流与多菌灵浓度呈现良好的线性关系.该复合物修饰电极可快速、方便、灵敏地检测溶液中多菌灵含量.     

石墨烯-Nafion修饰电极同时测定邻苯二酚、对苯二酚

通过恒电位法将氧化石墨烯还原为石墨烯,制备了石墨烯-Nafion修饰玻碳电极.用循环伏安法研究了邻苯二酚和对苯二酚两种异构体在该电极上的电化学行为.结果表明,该修饰电极对苯二酚的这两种异构体的氧化表现出了优异的识别能力和电催化性能.对苯二酚和邻苯二酚的氧化峰电位差值为102 mV,这表明两种异构体可以在石墨烯-Nafion修饰电极上完全分开.基于对苯二酚和邻苯二酚在石墨烯-Nafion修饰电极上的伏安行为,建立了苯二酚两种异构体同时测定的方法.在最佳实验条件下,邻苯二酚的浓度在6.0×10-5~1.0×10-3mol/L范围内与氧化峰电流呈线性关系,检出限为1.0×10-5mol/L.对苯二酚的浓度在8.0×10-6~1.0×10-3mol/L范围内与氧化峰电流呈线性关系,检出限为2.0×10-6mol/L.该电极可用于模拟样品中两种异构体的同时测定,结果令人滿意.     

碳纳米管/壳聚糖复合膜修饰电极测定尿酸的研究

制备了一种碳纳米管/壳聚糖复合膜修饰的玻碳电极,并通过循环伏安法和计时库仑法详细研究了尿酸在复合膜修饰电极上的电化学行为.对诸如支持电解质,溶液pH,富集时间等实验条件进行了优化,结果表明,在pH＝3.95 0.1 mol/L柠檬酸钠盐支持电解质中,尿酸在复合膜修饰电极上具有良好的电化学响应.相对于裸玻碳电极,尿酸的氧化峰电位负移20 mV,峰电流显著提高,锋形更为尖锐,表明复合膜对尿酸的电化学氧化具有一定的催化作用,计时库仑法结果表明尿酸在复合膜修饰电极上为两电子两质子的电子转移过程.尿酸的氧化峰电流与其浓度分别在5.0×10－9～5.0×10－7 mol/L范围内和1.5×10－6～1.0×10－4 mol/L范围内呈良好的线性关系,线性相关系数分别是0.994 7和0.988 4.开路富集120 s后,检出限为5.0×10－9 mol/L.将该复合膜修饰电极应用于人体实际尿样中尿酸的测量,结果令人满意.     

多巴胺在L-半胱氨酸修饰玻碳电极上的电化学行为及伏安测定

以L-半胱氨酸作为电极修饰剂,采用循环伏安法研究L-Cys/GC电极的制备和DA在该修饰电极的电化学行为及其测定.DA在pH=6.684的磷酸盐缓冲溶液中,在L-Cys/GC电极上产生一对灵敏的氧化还原峰,峰电位分别为Epa=0.180 V和Epc=0.125 V（vs.SCE）.同时用伏安法测定DA的线性范围为1×10-3～1.0×10-6 mol/L,检出限可低达1.0×10-7mol/L（S/N=3）.对1×10-4 mol/L DA平行测定50次,其相对标准偏差约为2.5%.该电极可望进一步发展为微电极,用于生物活体内的神经递质DA的实际检测.     

尿酸在修饰玻碳电极上的电化学行为及测定研究——以碳纳米管-聚马来松香己二醇酯为例

研制以聚马来松香己二醇酯(PMHE)分散羧基化多壁碳纳米管的化学修饰电极(PMHE-MWC-NTs/GC),研究了尿酸(UA)在修饰电极上的电化学行为和测定方法.结果表明,在0.3mol/LHAc-NaAc(pH4.65)缓冲溶液中修饰电极对尿酸的氧化具有明显的催化和增敏作用,氧化峰电位由0.5V(裸电极)负移到0.573V,灵敏度增大约6倍.对各种实验条件进行了优化.定量测定的线性范围为1.0×10-6mol/L~7.0×10-4mol/L(r=0.9968),检出限为1.0×10-7mol/L.利用该法直接测定了人体尿样中尿酸的含量,结果满意.     

层层组装纳米金/天冬氨酸传感器对尿酸的电化学性质研究

采用层层组装法制备了金和天冬氨酸复合膜传感器.用循环伏安法(CV)和脉冲伏安法(DPV)等研究了尿酸在该传感器上的电化学行为.结果表明,在PBS 7.0作为支持电解质的条件下,尿酸在该组装传感器上的氧化峰的峰电流是裸电极传感器上的6.5倍.优化条件下,用DPV对尿酸进行了测定,在尿酸浓度为4.0×10-7~1.0×10-4 mol/L范围内浓度与尿酸的氧化峰电流具有良好的线性关系,线性方程为:I(μA)=0.010-0.022 C(μmol/L),相关系数为0.998.检出限(RSN=3)为1.0×10-7 mol/L.该方法用于实际尿样的测定,回收率为99.4%~104.1%.     

L-色氨酸在单壁碳纳米管/玻碳修饰电极上的电化学行为及其分析研究

用循环伏安法和线性单扫描伏安法研究了L-色氨酸在单壁碳纳米管/玻碳修饰电极上的电化学行为,探讨了不同缓冲液、pH值以及扫描速度等的影响.实验表明在pH=5的乙酸铵介质中,L-色氨酸在单壁碳纳米管/玻碳修饰电极上的电氧化过程是一完全不可逆过程,于0.703 V(vs. SCE)处产生一灵敏的不可逆氧化峰,峰电位相对于裸玻碳电极负移55mV,峰电流大大增加.峰电流与L-色氨酸的浓度在5.0×10-6-1.0×10-4 mol/L 范围内有良好的线性关系,相关系数R为0.9984,检出限为1.0×10-7mol/L,样品检测平均回收率为98.80%.     

聚苯乙烯磺酸钠/单壁碳纳米管复合膜修饰电极对体系中抗坏血酸、尿酸、多巴胺的的电分离研究

制备了聚苯乙烯磺酸钠(PSS)/单壁碳纳米管(SWNTs)膜修饰玻碳电极,在磷酸盐缓冲溶液(PBS)中,研究了抗坏血酸(AA)、尿酸(UA)、多巴胺(DA)在该修饰电极上的电化学行为.结果表明:AA、UA、DA在该修饰电极上的氧化信号能得到明显地区分,峰电位差值DA-AA为158mV,DA-UA为118 mV,AA-UA为276 mV.利用示差脉冲伏安法对体系中抗坏血酸(AA)、尿酸(UA)、多巴胺(DA)可以同时进行检测.其线性响应范围分别为1.0×10-3-1.0×10-4mol/L(AA);7.4×10-7-7.0×10-6mol/L(DA);1.0×10-6-1.0×10-5mol/L(UA).该方法用于针剂中多巴胺的检测,回收率在102.0-106.0%之间.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.