磁控溅射ZnO薄膜的三阶非线性光学特性

采用磁控溅射技术在SiO_2衬底上制备ZnO薄膜,并通过X射线衍射仪、原子力显微镜、紫外-可见分光光度计和荧光光谱仪对薄膜的晶体结构、表面形貌、带隙宽度和光致发光性质进行测试表征,结合飞秒激光(波长为800nm,脉宽50fs)和Z扫描方法测量该薄膜的三阶非线性光学特性.结果表明,其三阶非线性折射率和非线性吸收系数均为正值,分别为3.50×10-18 m2/W和2.88×10-11 m/W.     

钛酸铅光学特性的第一性原理研究

采用广义梯度近似下的密度泛函方法对PbTiO3顺电相进行研究.计算得到PbTiO3直接带隙及间接带隙的大小分别为1.77和1.66eV,且研究了PbTiO3的介电函数、反射系数、吸收系数、能量损失系数、折射系数和湮灭系数等光学性质,并基于电子能带结构对光学性质进行了解释.     

中频反应磁控溅射Al_2O_3薄膜的光学性质

采用中频反应磁控溅射技术在玻璃基片上制备了Al2O3薄膜,提出了一种利用透射光谱来简单有效地分析弱吸收薄膜的光学特性及与光学相关的其他物理特性的方法.对Al2O3薄膜进行透射谱测量,通过对薄膜折射率、吸收系数、膜厚度与入射光波长相互关系的分析,获得了Al2O3薄膜在400~1 100 nm区域内的折射率、吸收系数与入射光波长的关系式,以及Al2O3薄膜厚度的计算公式.     

磁控溅射制备TiO_2薄膜及其光学特性研究

采用直流反应磁控溅射法在玻璃衬底上制备TiO2薄膜.用紫外-可见光分光光度计和AFM分别表征了薄膜的透射率和表面形貌,用包络线法详细研究了不同衬底温度下TiO2薄膜的光学特性.结果表明:薄膜在可见光波段有很高的透明度,且随着衬底温度的升高,薄膜的透射率略有增加,薄膜的折射率和吸收系数增大,薄膜的光学带隙减小;同时,薄膜表面粗糙度减小,薄膜变得平整.     

0.74Pb(Mg_(1/3)Nb_(2/3))O_3-0.26PbTiO_3薄膜的光学性能研究

采用磁控溅射法,选用LaNiO3(LNO)作为缓冲层和电极层,在硅基片上成功地制备出了0.74Pb(Mg1/3Nb2/3)O3-0.26PbTiO3(PMN-0.26PT)铁电薄膜.X射线衍射(XRD)分析表明薄膜具有沿(110)方向择优取向的钙钛矿结构.利用NKD光谱测试仪测试了薄膜的反射谱,并使用最小二乘法进行拟合分析得到其折射率和消光系数.在沉积温度为500℃时,薄膜具有更为均匀和致密的微观结构.在波长为633 nm时,该薄膜的折射率大小为2.41.薄膜的折射率和消光系数随着光子能量的增加而增加.薄膜的这些光学特性使其有望在低压电光转换器、光波导等器件中应用.     

掺Cu的SrBi2Ta2O9薄膜的非线性光学特性的研究

以SrBi2Ta2O9陶瓷和高纯Cu片作为靶材,利用射频磁控溅射方法在双面抛光的石英基片上制备了掺Cu金属颗粒的SrBi2Ta2O9复合薄膜.用XRD和AFM表征了薄膜的结晶性能和表面形貌;利用单光束Z扫描技术在波长532 nm处测量了薄膜的非线性光学特性,其三阶非线性光学极化率的实部Reχ(3)=2.26×10-9esu,虚部Imχ(3)=0.62×10-9esu.     

(PSTT10/45)4 多层薄膜铁电性研究

以LaNiO3做缓冲层,用射频磁控溅射法在SiO2/Si(100)衬底上制备出[0.9Pb(Sc0.5Ta0.5)O3-0.1PbTiO3/0.55Pb(Sc0.5Ta0.5)O3-0.45PbTiO3]4铁电多层薄膜.采用两步法在峰值温度800 ℃对薄膜进行退火.通过x射线衍射分析了薄膜的物相结构,通过电滞回线和漏电流曲线对薄膜的铁电性能进行了测量.研究发现,薄膜展现出高度(100)取向的钙钛矿结构和增强的铁电性,其剩余极化2Pr=26.2 μc/cm2,矫顽场2Ec=53.9 kV/cm,100 kV/cm下漏电流密度为1.87×10-4A/cm2.分析了铁电性增强和漏电流增大的可能原因.     

0.9Pb(Sc1/2Ta1/2)O3-0.1PbTiO3/0.65Pb(Mg1/3Nb2/3) O3-0.35PbTiO3 多层薄膜的制备及铁电性研究

以LaNiO3做缓冲层,用射频磁控溅射法在SiO2/Si(100)衬底上制备出0.9Pb(Sc1/2Ta1/2)O3 -0.1PbTiO3/0.65Pb(Mg1/3Nb2/3)O3-0.35PbTiO3铁电多层薄膜.采用两步法在峰值温度650℃和700℃对薄膜进行退火.通过电滞回线和漏电流曲线对薄膜的铁电性能进行了测量.研究发现,650 ℃退火的薄膜有较好的铁电性,其剩余极化2Pr=9.5 μc/cm2,矫顽场2Ec=42.2 kV/cm,100 kV/cm场强下漏电流密度为31μA/cm2.700 ℃退火的薄膜铁电性有所下降,2Pr=3.1 μc/cm2,但薄膜却具有很低的矫顽场,2Ec=22.6 kV/cm.分析认为,铁电性的退化与高温下薄膜中异质结间的相互作用及挥发性元素Pb和Mg的损失密切相关.     

掺Nd~(3+)硼硅酸盐玻璃的非线性光学特性

在调Q 纳秒Nd: YAG强激光脉冲下,使用闭孔Z-扫描技术研究了硼硅酸盐基质玻璃及其掺Nd3+玻璃的三阶光学非线性特性.发现基质玻璃具有正的三阶非线性折射系数和非线性吸收系数,属于自聚焦反饱和吸收型的光学介质;而随着Nd3+的掺入,该硼硅酸盐玻璃的三阶非线性折射和吸收系数较基质玻璃有明显的增大,远高于一个量级.用开孔Z-扫描实验与光限幅实验进一步验证了掺Nd3+玻璃具有较高的三阶非线性吸收系数,表明Nd3+的掺入提高了硼硅酸盐玻璃在532 nm处的激光防护性能.     

一种可溶性聚对苯衍生物三阶非线性光学性能研究

为了研究聚对苯衍生物的三阶非线性光学性能,采用三氯化铁法合成了一种对称己氧基取代聚对苯衍生物(DHO PPP),该聚合物具有良好的溶解性和成膜性.在紫外吸收光谱上,DHO PPP的三氯甲烷溶液和薄膜在波长为532 nm处具有很小的线性吸收.采用标准后向简并四波混频系统在532 nm下对该聚合物的三氯甲烷稀溶液的三阶非线性光学效应进行了研究,发现三阶非线性极化率以及非线性折射率随溶液质量浓度的增加而线性增加,而二阶分子超极化率稳定在1 78×10-30 esu附近.当质量浓度达到5 g/L时,三阶非线性极化率为6 31×10-11 esu,非线性折射率达到1 65×10-9 esu.研究结果表明,DHO PPP具有良好的三阶非线性光学性能.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

An on-line scaling method for improving scalability of a database cluster

The explosive growth of the Internet and database applications has driven database to be more scalable and available, and able to support on-line scaling without interrupting service. To support more client's queries without downtime and degrading the response time, more nodes have to be scaled up while the database is running. This paper presents the overview of scalable and available database that satisfies the above characteristics. And we propose a novel on-line scaling method. Our method improves the existing on-line scaling method for fast response time and higher throughputs. Our proposed method reduces unnecessary network use, i.e. , we decrease the number of data copy by reusing the backup data. Also, our on-line scaling operation can be processed parallel by selecting adequate nodes as new node. Our performance study shows that our method results in significant reduction in data copy time.     

An improved R-tree based on childnode''s probability

R-Tree is a good structure for spatial searching. But in this indexing structure,either the sequence of nodes in the same level or sequence of traveling these nodes when queries are made is random. Since the possibility that the object appears in different MBR which have the same parents node is different, if we make the subnode who has the most possibility be traveled first, the time cost will be decreased in most of the cases. In some case, the possibility of a point belong to a rectangle will shows direct proportion with the size of the rectangle. But this conclusion is based on an assumption that the objects are symmetrically distributing in the area and this assumption is not always coming into existence. Now we found a more direct parameter to scale the possibility and made a little change on the structure of R-tree, to increase the possibility of founding the satisfying answer in the front sub trees. We names this structure probability based arranged R-tree (PBAR-tree).     

Integrating GIS Web services based on mediating architecture

The geographic information service is enabled by the advancements in general Web service technology and the focused efforts of the OGC in defining XML-based Web GIS service. Based on these models, this paper addresses the issue of services chaining,the process of combining or pipelining results from several interoperable GIS Web Services to create a customized solution. This paper presents a mediated chaining architecture in which a specific service takes responsibility for performing the process that describes a service chain. We designed the Spatial Information Process Language (SIPL) for dynamic modeling and describing the service chain, also a prototype of the Spatial Information Process Execution Engine (SIPEE) is implemented for executing processes written in SIPL. Discussion of measures to improve the functionality and performance of such system will be included.     

Tracking data management using topology of moving object database system for moving object constrained trajectory in LBS application

Advances in wireless technologies and positioning technologies and spread of wireless devices, an interest in LBS (Location Based Service) is arising. To provide location based service, tracking data should have been stored in moving object database management system (called MODBMS) with proper policies and managed efficiently. So the methods which acquire the location information at regular time intervals then, store and manage have been studied. In this paper, we suggest tracking data management techniques using topology that is corresponding to the moving path of moving object. In our techniques, we update the MODBMS when moving object arrived at a street intersection or a curved road which is represented as the node in topology and predict the location at past and future with attribute of topology and linear function. In this technique, location data that are corresponding to the node in topology are stored, thus reduce the number of update and amount of data. Also in case predicting the location,because topology are used as well as existing location information, accuracy for prediction is increased than applying linear function or spline function.