Subsurface macro-inclusions and solidified hook character in aluminum-killed deep-drawing steel slabs

Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ultralow carbon (ULC) steel slabs and two low carbon (LC) aluminum-killed steel slabs were sampled to study the relationship between hooks and subsurface macro-inclusions, which were detected on the cross-sections of steel samples with an area of 56058 mm2 using an automated scanning electron microscopy/energy-dispersive X-ray spectroscopy system. Results show that subsurface inclusions larger than 200 μm were almost entrapped by hook structures, whereas the location of other inclusions smaller than 200 μm had no obvious dependence on the location of solidified hooks. Furthermore, the number density (ND) of subsurface inclusions larger than 200 μm decreased from 0.02 to 0 cm-2 in ULC steel as the mean hook depth decreased from 1.57 to 1.01 mm. Similar trends were also observed in LC steel. In addition, the detected inclusions larger than 200 μm were concentrated in the region near the slab center (3/8 width-5/8 width), where hook depths were also larger than those at any other locations. Therefore, minimizing the hook depth is an effective way to reduce inclusion-induced sliver defects in deep-drawing steels.     

Effects of basicity and MgO content on the viscosity of the SiO2-CaO-MgO-9wt%Al2O3 slag system

The effects of basicity and MgO content on the viscosity of SiO2-CaO-MgO-9wt%Al2O3 slags with basicity from 0.4 to 1.0 and MgO content from 13wt%to 19wt%were investigated using the rotating cylinder method. A correlation between the viscosity and the slag structure was determined by Fourier transform infrared （FTIR） spectroscopy. It is indicated that the complex network structure of the slag melt is depolymerized into simpler network units with increasing basicity or MgO content, resulting in a continuous decrease in viscosity of the slag. The viscosity is strongly dependent on the combined action of basic oxide components in the slag. Under the present experimental conditions, increasing the basicity is found to be more effective than increasing the MgO content in decreasing the viscosity of the slag. At higher temperatures, the increase of basicity or MgO content does not appreciably decrease the viscosity of the slag, as it does at lower tem-peratures. The calculated activation energy of viscous flow is between 154 and 200 kJ＆#183;mol-1, which decreases with an increase in basicity from 0.4 to 1.0 at a fixed MgO content in the range of 13wt%to 19wt%.     

Experimental study on stability control technology of surrounding rock of deep roadways in coal mine

In order to solve effectively the problems of deep mining with safety and high efficiency, the multi- pie factors influencing the stability of deep rock roadway and technical problems are analyzed in the light of the severe situation of effective mining for deep coal resource, and the stability control methods for deep rock road- way are provided, which are based on the idea of combined support with separated steps and integral control of surrounding rock of deep rock roadway. The suggested methods were applied to a deep rock roadway with -648 m depth in Gubei coal mine of Huainan area. The field test was carried out and the in-situ monitoring was imple- mented, and the support scheme was optimized and adjusted to improve the stability of the surrounding rock of the roadway based on the feedback analysis. The results showed that the stability can be improved greatly by the provided control methods tbr deep roadway. The present methods lbr stability control of deep rock roadway can be used to other deep rock roadways with the similar conditions.     

Influence of Te doping on the dielectric and optical properties of InBi crystals grown by directional freezing

Stoichiometric pure and tellurium (Te) doped indium bismuthide (InBi) were grown using the directional freezing technique in a fabricated furnace. The X-ray diffraction profiles identified the crystallinity and phase composition. The surface topographical features were observed by scanning electron microscopy and atomic force microscopy. The energy dispersive analysis by X-rays was performed to identify the atomic proportion of elements. Studies on the temperature dependence of dielectric constant (?), loss tangent (tanδ), and AC conductivity (σ_ac) reveal the existence of a ferroelectric phase transition in the doped material at 403 K. When InBi is doped with tellurium (4.04 at%), a band gap of 0.20 eV can be achieved, and this is confirmed using Fourier transform infrared studies. The results thus show the conversion of semimetallic InBi to a semiconductor with the optical properties suitable for use in infrared detectors.     

LBE–DEM simulation of inter-phase heat transfer in gas–solid cross jets

Lattice-Boltzmann equation(LBE)–Discrete element method(DEM)coupled simulation of a twodimensional gas–solid cross jet is performed,focusing on the gas-particle two-way coupling effect on heat transfer characteristics.The Reynolds number is 1000,and particle Stokes numbers are 10,25,and 50 under the same number flow rate of particles.The gas phase temperature field and particle distribution as well as the inter-phase heat transfer characteristics are studied and analyzed.The dominating effects,i.e.the mean temperature difference and mean heat transfer coefficient between the gas–solid phases,for the pre-and post-collision stages of the cross jets are illustrated respectively.The change of dominating roles is related to the dynamical response characteristics of particles.     

Cache performance optimization of irregular sparse matrix multiplication on modern multi-core CPU and GPU

This paper focuses on how to optimize the cache performance of sparse matrix-matrix multiplication （SpGEMM）.It classifies the cache misses into two categories：one is caused by the irregular distribution pattern of the multiplier-matrix,and the other is caused by the multiplicand.For each of them,the paper puts forward an optimization method respectively.The first hash based method removes cache misses of the 1 st category effectively,and improves the performance by a factor of 6 on an Intel 8-core CPU for the best cases.For cache misses of the 2nd category,it proposes a new cache replacement algorithm,which achieves a cache hit rate much higher than other historical knowledge based algorithms,and the algorithm is applicable on CELL and GPU.To further verify the effectiveness of our methods,we implement our algorithm on GPU,and the performance perfectly scales with the size of on-chip storage.     

A study on the characterization of smoke movement in shafts with different fire source positions

In this study, experimental and numerical simulation methods were combined to simulate the changing course of the temperature and velocity fields in nine different fire scenes. The characteristics of smoke movement in shafts with different fire source position factors （h/H） were quantitatively investigated, and the non-dimensional fitting function between the fire source position factors and the maximum temperature was deduced. The results showed that the location of the neutral plane moved upward as the fire source rose, and all the generated smoke spread to the upper areas; however, there was barely any smoke in the lower areas. The maximum temperature was inversely proportional to the fire source position factor; the higher the source position is, i.e. the higher the ra- tio factor is, the lower the maximum temperature is in the shaft. The experimental verification of the fire dynamics simulator （FDS） showed good results.     

Full-scale model tests and nonlinear analysis of prestressed concrete simply supported box girders

Full-scale model tests were carried out on a 30 m span prestressed concrete box girder and a 20 m span prestressed concrete hollow slab. Failure models were prestressed reinforcement tensile failure and crashing of roof concrete, respectively. The ductility indexes of the box girder and hollow slab were 1.99 and 1.23, respectively, according to the energy viewpoint. Based on the horizontal section hypothesis, the nonlinear computation procedure was established using the limited banding law, and it could carry out the entire performance analysis including the unloading, mainly focusing on the ways to achieve the unloading curves computation through stress-strain, moment-curvature and load-displacement curves. Through the procedure, parameters that influence on the bearing capacity, deformation performance and ductility of the structures were analyzed. Those parameters were quantity of prestressed reinforcement and tension coefficients of prestressed reinforcement. From the analysis, some useful conclusions can be obtained.     

Microstructure and mechanical properties of （Ti,AI,Zr）N/（Ti,AI,Zr,Cr）N films on cemented carbide substrates

（Ti,Al,Zr）N/（Ti,Al,Zr,Cr）N bilayer films were deposited on cemented carbide （WC-8%Co） substrates by multi-arc ion plating （MAIP） using two Ti-AI-Zr alloy targets and one pure Cr target. To investigate the composition, morphology, and crystalline structure of the bilayer films, a number of complementary methods of elemental and structural analysis were used, namely, scanning electron microscopy （SEM）, energy disperse X-ray spectroscopy （EDS）, and X-ray diffraction （XRD）. Adhesive strength and mechanical properties of the films were evaluated by scratch testing and Vickers microindentation, respectively. It is shown that the resulting films have a TiN-type face-centered cubic （FCC） structure. The films exhibit fully dense, uniform, and columnar morphology. Furthermore, as the bias voltages vary from -50 to -200 V, the microhardness （max. Hv001 4100） and adhesive strength （max. 〉 200 N） of the bilayer films are superior to those of the （Ti,Al,Zr）N and （Ti,Al,Zr, Cr）N monolayer films.     

Integrated development and industrial application of high sour natural gas purification technology

Aiming at acute characteristics of flammability, explosibility, causticity and leakiness of high sour nat- ural gas, giving full consideration to local natural conditions in Sichuan Province and starting with purification pro- cess, the paper analyzed process configurations, energy utilization and conservation, safety and environment pro- tection measures. The integrated technology and engineering scheme for high sour natural gas purification was es- tablished and successfully used in industrial application.     

Adaptive and local analysis of climate data

This paper focuses on how to extract physically meaningful information from climate data, with em- phases placed on adaptive and local analysis. It is argued that many traditional statistical analysis methods with rigorous mathematical footing may not be efficient in extracting essential physical information from climate da- ta; rather, adaptive and local analysis methods that agree well with fundamental physical principles are more ca- pable of capturing key information of climate data. To illustrate the improved power of adaptive and local analy- sis of climate data, we also introduce briefly the empirical mode decomposition and its later developments.     

The HITCR-I： Evaluation on a free gait generation method for the hexapod robot on irregular terrain

The purpose of this paper is to present and evaluate a method of free gait generation for HITCRI,a hexapod walking robot.The HITCR-I is designed as a modularized structure of legs that is based upon a four-bar linkage mechanism and with force sensors in the tip of legs,distributed hardware structure and a modular software structure of the control system.Based on a set of local rules between adjacent legs,finite state machine （FSM） model is built to control the coordination of legs.An automatic smooth transition of gait pattern is achieved through deriving the mathematical relation between gait pattern and locomotion parameters.The disordered inter-leg phase sequence is adjusted to a regular state smoothly and quickly by the local rules based FSM,and the gait pattern can transform automatically adapting to irregular terrain.The experiment on HITCR-I has demonstrated that it can walk through irregular terrain reliably and expeditiously with the free gait controller designed in this paper.     

Influence of Rare Earth Elements on Mechanical Properties and Corrosion Resistance of Cu-15Ni Alloy

In order to improve the mechanical property and Cl-+S2-corrosion resistance of B15 copper-nickel alloy,Cu-15Ni-xRE(x:0-0.1%by weight)alloy was prepared by adding rare earth(RE)in melted Cu-15Ni alloy using metal mould casting method.Optical microscopy(OM),electronic tensile testing machine,X-ray diffraction(XRD),scanning electron microscope(SEM),and electrochemical testing system were used to analyze mechanical property,corrosion resistance property,and surface microstructure of different treatment samples.The results of OM and tensile testing show that the RE addition can effectively deoxidize the alloy melt and the microstructure of the alloy changes from coarse dendrite to small equiaxed grain.By addition of 0.05%RE,the tensile strength and elongation of Cu-15Ni alloys are improved from 294 MPa to 340MPa,and 8%to 33.5%respectively.The results of electrochemical testing show that the corrosion resistance of Cu-15Ni alloy is greatly improved by adding proper amount of RE,whereas excess addition of RE worsens the corrosion resistance.The optimum RE content was about 0.05%by weight.In comparison with the alloy without RE,the corrosion potential and corrosion current density of Cu-15Ni alloy containing proper RE decreased by about-0.28 V and 70A/cm2,respectively.     

Determining the approach speed envelope of carrier aircraft

Many factors, such as deck motion and air wave, influence the determination of the approach speed which has an important effect on landing safety. Until recently, there are no design criteria about approach speed of carrier aircraft in the current standards and available publications. Therefore, the requirements of stall margin, longitudinal acceleration ability, altitude correction and field-of-view on approach speed were researched. Based on the flight dynamics model, the flight simulations were conducted to study the effect of the response time of en- gine, wave off requirements, elevator efficiency and deflection rate on the approach speed. The results presented that the approach longitudinal acceleration and altitude correction ability had crucial influence on the approach speed envelope of the aircraft. The limitations of the control requirements, field-of-view requirements and gear were also given through the simulation and analysis. Based on the above results, the approach speed envelope were determined.     

Synthesis and formation mechanism of micro/nano flower-like MgCO3·5H2O

Micro/nano magnesium carbonate pentahydrate（MgCO3 ·5H2 O） with flower-like morphology was synthesized using magnesite as a substrate and potassium dihydrogen phosphate as an additive. The synthesized samples were characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetry and differential scanning calorimetry. The influence of pyrolysis time on crystal morphology was explored. The formation mechanism was investigated on the basis of the characterized results and the crystal structure of MgCO3 ·5H2 O. The results showed that the flower-like MgCO3 ·5H2 O was 1.5-3.0 μm in length and 100-500 nm in diameter and was successfully obtained with a pyrolysis time of 30 min. The formation mechanism of flower-like MgCO3 ·5H2 O is suggested to be the selective adsorption of potassium dihydrogen phosphate on the surface. The process of flower-like crystal growth is as follows： amorphous nanoparticles formation, acicular and rod monocrystal formation, flower-like monocrystal formation, and flower-like polymers（MgCO3 ·5H2 O） crystallization. In the MgCO3 ·5H2 O crystal, the magnesium ion presents two different octahedral coordinations corresponding to2 26 Mg（H O）＋and2 2 2 4 23 [Mg（H O）（CO） ]--, and the chemical formula of the crystal is2 2 6 2 4 23 Mg（H O） Mg（H O）（CO）2.     

Load compensation research on twicetension for loop anchor cable of inner lining in Yellow River-crossing tunnel

The load compensation equipment for anchor cable named low retraction prestressed anchorage system with twice-tension （referred to as twice-tension anchorage system） is proposed in the paper. Calculation results of loop anchorage prestressing loss （PL） values of inner lining （IL）in Yellow River-crossing tunnel under two anchorage systems, including twice-tension anchorage system and HM （Chinese transliteration is huanmao） anchorage system, are introduced. The software ANSYS is selected to realize the three-dimensional （3D） finite element modeling to accomplish simulation and calculation works under the two anchorage systems, respectively. Stress processes of IL under the two working conditions, of which one is completed cable tensioning （CCT） and the other is water in the tunnel with the designed water pressure （DWP）, are contrasted and analyzed. Impacts of prestressing forces of anchor cables on structural safety under the two anchorage systems are contrasted. The calculation results show that the twice-tension anchorage system can reduce PL effectively and then increase prestresses of wall concrete （WC）. Meanwhile, the anchorage system has the advantages of improving security and stability of tunnel structure, reducing project costs and saving steel consumption. The research work is available to related design and construction of anchor cable, and is worthy of promotion and application.     

Microstructure, crystallography and nucleation mechanism of NANOBAIN steel

The microstructure of bainite ferrite in NANOBAIN steel transformed at different temperatures was investigated by scanning electron microscopy, transmission electron microscopy, electron back-scattered diffraction, and vickers hardness tester in detail. It is found that the average width of bainitic ferrite (BF) plates can be refined to be thinner with the reduction of temperature (473–573 K), and the bainitic ferrite plates can reach up to 20–74 nm at 473 K. Crystallographic analysis reveals that the bainitic ferrite laths are close to the Nishiyama-Wasserman orientation relationship with their parent austenite. Temperature shows a significant effect on the variant selection, and a decrease in temperature generally weakens the variant selection. Thermodynamic analyses indicates that the Lacher, Fowler and Guggenheim (LFG) model is more suitable than the Kaufman, Radcliffe and Cohen (KRC) model dealing with NANOBAIN steel at a low temperature range. The free energy change ΔGγ→BF is about ?1500 J·mol?1 at 473 K, which indicates that nucleation in NANOBAIN steel is the shear mechanism. Finally, the formation of carbon poor regions is thermodynamically possible, and the existence of carbon poor regions can greatly increase the possibility of the shear mechanism.     

Automatic Collecting Representative Logo Images from the Internet

With the explosive growth of commercial Iogos, high quality logo images are needed for training logo detection or recognition systems, especially for famous Iogos or new commercial brands. This paper focuses on automatic collecting representative logo images from the internet without any human labeling or seed images. We propose multiple dictionary invariant sparse coding to solve this problem. This work can automatically provide prototypes, representative images, or weak labeled training images for logo detection, logo recognition, trademark infringement detection, brand protection, and ad-targeting. The experiment results show that our method increases the mean average precision for 25 types of Iogos to 80.07% whereas the original search engine results only have 32% representative logo images. The top images collected by our method are accurate and reliable enough for practical applications in the future.     

Dynamic recrystallization and precipitation in high manganese austenitic stainless steel during hot compression

Dynamic recrystallization and precipitation in a high manganese austenitic stainless steel were investigated by hot compression tests over temperatures of 950–1150℃ at strain rates of 0.001 s?1-1 s?1. All the flow curves within the studied deformation regimes were typical of dynamic recrystallization. A window was constructed to determine the value of apparent activation energy as a function of strain rate and deformation temperature. The kinetics of dynamic recrystallization was analyzed using the Avrami kinetics equation. A range of apparent activation energy for hot deformation from 303 kJ/mol to 477 kJ/mol is obtained at different deformation regimes. Microscopic characterization confirms that under a certain deformation condition (medium Zener-Hollomon parameter (Z) values), dynamic recrystallization appears at first, but large particles can not inhibit the recrystallization. At low or high Z values, dynamic recrystallization may occur before dynamic precipitation and proceeds faster. In both cases, secondary phase precipitation is observed along prior austenite grain boundaries. Stress relaxation tests at the same deformation temperatures also confirm the possibility of dynamic precipitation. Unexpectedly, the Avrami’s exponent value increases with the increase of Z value. It is associated with the priority of dynamic recrystallization to dynamic precipitation at higher Z values.     

Dynamic Characteristic Study of Ball Screw Feed Drive Systems Based on Multi-flexible Body Model

A new ball screw dynamic model was developed under the adequate consideration of the interaction in the screw-nut assembly （not only the mutual-coupling factors but also the self-coupling factors） . Based on this model,the multi-flexible body （MFB）dynamic model of ball screw feed drive system was then founded in order to take full account of the influencing factor of system flexibility and study the dynamic behaviors of the whole mechanical transmissions. Moreover,the MFB based state space modeling was proposed by modal state space method, which extraced the eigenmodes of more dominant modes and applied them into an MFB state space model,and realized the integrated model of servo drives and MFB mechanical transmissions more effectively and efficiently. In conclusion,the comparisons between simulations and experimental results show： the stiffness formulation of the ball screw assembly derived above is a suitable method for achieving accurate MFB models of ball screw mechanical transmission systems,this proposed MFB model is valid,and the integrated model of ball screw feed drive system is accurate and reliable. All these provide the important approaches and guidelines for dynamic characteristic study and selection of control parameters in the machine tool design period.