烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

含钛高炉炉渣微波合成碳化钛及其介电性能测定

The preparation of functional material titanium carbide by the carbothermal reduction of Ti-bearing blast furnace slag with microwave heating is an effective method for valuable metals recovery; it can alleviate the environmental pressure caused by slag stocking. The dynamic dielectric parameters of Ti-bearing blast furnace slag/pulverized coal mixture under high-temperature heating are measured by the cylindrical resonant cavity perturbation method. Combining the transient dipole and large π bond delocalization polarization phenomena, the interaction mechanism of the microwave macroscopic non-thermal effect on the titanium carbide synthesis reaction was revealed. The material thickness range during microwave heating was optimized by the joint analysis of penetration depth and reflection loss, which is of great significance to the design of the microwave reactor for the carbothermal reduction of Ti-bearing blast furnace slag.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

两类粘合图的 Wiener与 Harary指数

连通图G的Wiener指数是指图G中所有点对的距离之和,Harary指数是指图G中所有点对的距离的倒数之和。本文主要研究了单圈图与双圈图的粘合图以及双圈图与双圈图的粘合图的Wiener指数的下界和Harary指数的上界的问题,并刻画了对应的极值图。     

东北生态类型单雌蓖麻遗传规律研究

控制单雌蓖麻单雌性状的基因为4对,其中3对为隐性重叠基因,用符号ai表示,Ai对ai为显性;另外一对为隐性抑制基因,用符号b表示,B对b为显性．纯合隐性基因bb对隐性重叠基因a1a1a2a2a3a3起抑制作用,使得a1a1a2a2a3a3bb（保持株）表现为正常两性株,a1a1a2a2a3a3BB（纯合型）和a1a1a2a2aa3a3Bh（杂合型）表现为单雌株．还有一组控制性转换的修饰基因,当温度过低或极高时,该基因才发生作用,从而使单雌蓖麻出现一些极端分离的比例现象．纯合型单雌株与保持株杂交,可获得全雌系．全雌系与恢复系杂交,F1代全为正常两性株,这样即可用全雌系、保持系、恢复系实现蓖麻三系法制种．     

关于多边形的顶点重心与圆内接多边形的垂心的若干结论

利用递归方法给出任意多边形的中线与顶点重心的定义,再给出圆内接多边形高线的定义,然后证明圆内接多边形的高线(或所在直线)共点,由此得到圆内接多边形垂心的定义,最后给出多边形的顶点重心与圆内接多边形的垂心的若干性质。     

固体推进剂用液体硝酸酯增塑剂冰点的测定及其方法的研究

液体增塑剂的冰点,直接影响着推进剂的低温力学性能.通过测熔点的方法,测试了硝化甘油(NG),1,2,4-丁三醇三硝酸酯(BTTN),-缩二乙二醇二硝酸酯(DEGN)和它们不同比例混溶物的冰点.为配方设计提供了必要的理论依据。     

采煤机运动参数对工作面温升的影响

采煤工作面的温度关系到工人的健康、设备的使用性能和煤炭生产的安全。为了研究采煤机运动参数对工作面温升的影响,建立了采煤机设计参数与工作面温升关系的数学模型,分析了采煤机的牵引速度、滚筒转速与工作面温升之间的关系及其影响。模拟结果表明,采煤机的运动参数对工作面的温升有直接的影响,工作面的温度随采煤机牵引速度的提高迅速增加,滚筒转速对工作面的温升影响较大;适当降低采煤机的牵引速度和滚筒转速能降低采煤工作面的温升。该结果为正确选择采煤机的运动参数、减少采煤机工作发热、降低采煤工作面温升、进一步改善采煤工作面的环境提供了依据。     

九运会体育馆钢屋盖预应力拉索施工技术

广州体育馆是新建成的第九届全国运动会用大型室内运动场，主场馆平面由两个对称的弓形组成，纵轴长160m，横轴长110m，屋面板全部为透光阳光板，屋盖为空间钢结构，在大跨度钢桁架之间采用了施加预应力的拉索支撑，与采用型钢支撑相比，拉索支撑内无压力，美观，而且有利于运动场采光，是一种新颖的先进结构，由于施加预应力，后批张拉时会对先行张拉的钢索内力有影响，屋架安装用支撑的拆除也会对已经张拉完成的钢索内力有影响，于是选择合理的钢索体系以及如何建立合适的钢索永存拉应力，对于本工程的施工既重要又是难点，文中介绍了该工程拉索的施工与检测技术。     

江西精神内涵初探

江西精神是中华民族优秀传统文化与时代精神的集中体现,主要内涵有:勤劳勇敢的务实精神;母仪天下的贤母精神;重教好学的育才精神;自强不息的改革精神;勤政为民的爱国精神;发明创造的科学精神;互助协作的团结精神;以天下为己任的创新精神;穷本溯源的探索精神;走向世界的开放精神;文章节义并重的精神;"星星之火,可以燎原"的理想信念精神;争创"第一等工作"的进取精神;顾全大局的奉献精神;塑造江西新形象精神;等等。     

环的 WGP-内射性

给出了 WGP-内射环的等价定义,研究了 WGP-内射环的一些性质,证明了：若 R 是左非奇异的左 WGP-内射环,且对 R 中任意无限序列 a1,a2,a3…,升链 1（a1）1（a1 a2）1（a1 a2 a3）…是平稳的,则 R 是半单环。     

二次曲线切线的一种新求法

利用点与点的对应和点与线的对应介绍二次曲线切线的一种新求法.     

伪的弱效应代数的同余和理想

在伪的弱效应代数的基础上给出伪的弱差分偏序集的概念,证明了伪的弱效应代数和伪的弱差分偏序集是等价的.通过引入伪的弱效应代数中的同余等概念证明了在特殊的同余条件下的商代数仍然是伪的弱效应代数,证明了满足RDP性质的伪BL-效应代数在特殊的同余关系下的商代数也是一个伪BL-效应代数并且具有子直积表示.