Hot corrosion behavior of nanostructured Gd2O3 doped YSZ thermal barrier coating in presence of Na2SO4 + V 2O5 molten salts

Nickel-based superalloy DZ125 was first sprayed with a NiCrAlY bond coat and followed with a nanostructured 2 mol% Gd_2O_3-4.5 mol% Y_2 O_3-ZrO_2(2 GdYSZ) topcoat using air plasma spraying(APS). Hot corrosion behavior of the as-sprayed thermal barrier coatings(TBCs) were investigated in the presence of 50 wt%Na_2SO_4 + 50 wt% V_2O_5 as the corrosive molten salt at 900 ℃ for 100 h. The analysis results indicate that Gd doped YVO_4 and m-ZrO_2 crystals were formed as corrosion products due to the reaction of the corrosive salts with stabilizers(Y_2O_3, Gd_2O_3) of zirconia. Cross-section morphology shows that a thin layer called TGO was formed at the bond coat/topcoat interface. After hot corrosion test, the proportion of m-ZrO_2 phase in nanostructured 2GdYSZ coating is lower than that of nano-YSZ coating. The result reveals that nanostructured 2GdYSZ coating exhibits a better hot corrosion resistance than nano-YSZ coating.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Microstructure and growth kinetics of Ce and Y jointly modified silicide coatings for Nb–Ti–Si based ultrahigh temperature alloy

In order to protect Nb-Ti-Si based ultrahigh temperature alloy from oxidation, pack cementation processes were utilized to prepare Ce and Y jointly modified silicide coatings. The Ce and Y jointly modified silicide coating has a double-layer structure: a relatively thick (Nb, X)Si2 (X represents Ti, Cr and Hf elements) outer layer and a thin (Ti, Nb)5Si4 transitional layer. The pack cementation experiments at 1150 ℃ for 8 h proved that the addition of certain amounts of CeO2 and Y2O3 powders in the packs distinctly influenced the coating thickness, the contents of Si, Ce and Y in the (Nb, X)Si2 outer layers, and the density of cavities in the coatings. In order to study the effects of Ce and Y joint modification in the silicide coatings, both only Ce and only Y modified silicide coatings were also prepared for comparison. The mechanisms of the beneficial effects of Ce and Y are discussed. A pack mixture containing 1.5CeO2-0.75Y2O3 (wt%) powders was employed to investigate the growth kinetics of the Ce and Y jointly modified silicide coating at 1050, 1150 and 1250 ℃. It has been found that the growth kinetics obeyed parabolic laws and the parabolic rate constants were 109.20 mm2/h at 1050 ℃, 366.75 mm2/h at 1150 ℃ and 569.78 mm2/h at 1250 ℃, and the activation energy for the growth of the Ce and Y jointly modified silicide coating was 197.53 kJ/mol.     

Facile synthesis of nanosized sodium magnesium hydride, NaMgH3

The ternary magnesium hydride NaMgH 3 has been synthesised via reactive milling techniques.The method employed neither a reactive H2 atmosphere nor high pressure sintering or other post-treatment processes.The formation of the ternary hydride was studied as a function of milling time and ball:powder ratio.High purity NaMgH 3 powder(orthorhombic space group Pnma,a 5.437(2),b 7.705(5),c 5.477(2) ;Z 4) was prepared in 5 h at high ball:powder ratios and characterised by powder X-ray diffraction(PXD),Raman spectroscopy and scanning electron microscopy/energy dispersive X-ray spectroscopy(SEM/EDX).The products formed sub-micron scale(typically 200-400 nm in size) crystallites that were approximately isotropic in shape.The dehydrogenation behaviour of the ternary hydride was investigated by temperature programmed desorption(TPD).The nanostructured hydride releases hydrogen in two steps with an onset temperature for the first step of 513 K.     

Synthesis of dental resins using diatomite and nano-sized SiO2 and TiO2

The mechanical properties of dental composites were improved by porous diatomite and nano-sized silica (OX-50) used as co-fillers.The resin composites,filled with silanized OX-50 and silanized diatomit...     

Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach

Cu-Ni-Si alloys are widely used due to their good electrical conductivities in combination with high strength and hardness. In the present work, minor-alloying with M =(Cr, Fe, Mo, Zr) was conducted for the objective of further improving their hardness while maintaining their conductivity level. A cluster-plus-glue-atom model was introduced to design the compositions of M-alloyed Cu-Ni-Si alloys, in which an ideal composition formula[(Ni,Si,M)-Cu_(12)]Cu_3(molar proportion) was proposed. To guarantee the complete precipitation of solute elements in fine δ-Ni_2 Si precipitates, the atomic ratio of(Ni,M)/Si was set as 2/1. Thus the designed alloy series of Cu_(93.75)(Ni/Zr)_(3.75)Si_(2.08)(Cr/Fe/Mo)_(0.42)(at%) were arc-melted into ingots under argon atmosphere, and solidsolutioned at 950 ℃ for 1 h plus water quenching and then aged at 450 ℃ for different hours. The experimental results showed that these designed alloys exhibit high hardness(HV 1.7 GPa) and good electrical conductivities(≥ 35% IACS). Specifically, the quinary Cu_(93.75)Ni_(3.54)Si_(2.08)(Cr/Fe)_(0.42)Zr_(0.21) alloys(Cu-3.32 Ni-0.93 Si-0.37(Cr/Fe)-0.30 Zr wt%) possess both a high hardness with HV = 2.5-2.7 GPa, comparable to the highstrength KLFA85 alloy(Cu-3.2 Ni-0.7 Si-1.1 Zn wt%,HV= 2.548 GPa),and a good electrical conductivity(35-36% IACS).     

Effect of Co addition on crystallization and magnetic properties of FeSiBPCu alloy

The effects of Co addition on the microstructure,crystallization processes and soft magnetic properties of(Fe1 xCox)83Si4B8P4Cu1(x?0.35,0.5,0.65)alloys were investigated.The experimental results demonstrated that the addition of Co decreased the thermal stability against crystallization of the amorphous phase,and thus improved the heat treatment temperature of this alloy.Fe Co Si BPCu nanocrystalline alloys with a dispersedα0-Fe Co phase were obtained by appropriately annealing the as-quenched ribbons at 763 K for 10 min.Theα0-Fe Co with grains size ranging from 9 to 28 nm was identified in primary crystallization.The coercivity(Hc)markedly increased with increasing x and exhibited a minimum value at x0.35,while the saturation magnetic flux density(Bs)shows a slight decrease.The(Fe0.65Co0.35)83Si4B8P4Cu1nanocrystalline alloy exhibited a high saturation magnetic flux density Bsof 1.68 T,a low coercivity,Hcof 5.4 A/m and a high effective permeability meof 29,000 at 1 k Hz.     

Effect of B2O3 on the aqueous tape casting and microwave properties of Li2O–Nb2O5–TiO2 ceramics

The effect of B2O3 addition on the aqueous tape casting, sintering, microstructure and microwave dielectric properties of Li2O-Nb2O5-TiO2 ceramics has been investigated. The tape casting slurries exhibit a typical shear-thinning behavior without thixotropy, but the addition of B2O3 increases the viscosity of the slurries significantly. It was found that doping of B2O3 can decrease the tensile strength, strain to failure and density of the green tapes. The sintering temperature could be lowed down to 900℃ with the addition of 2 wt% B2O3 due to the liquid phase effect. No secondary phase is observed. The addition of B2O3 does not induce much degradation on the microwave dielectric properties. Optimum microwave dielectric properties of εr 67, Q×f 6560 GHz are obtained for Li2O-Nb2O5-TiO2 ceramics containing 2 wt% B2O3 sintered at 900 1C. It represents that the ceramics could be promising for multilayer low-temperature co-fired ceramics (LTCC) application.     

Competing crystallite size and zinc concentration in silica coated cobalt ferrite nanoparticles

Silica coated(30 wt%) cobalt zinc ferrite(Co1 xZnxFe2O4, x?0, 0.2, 0.3, 0.4, 0.5 and 1) nanoparticles were synthesized by using sol–gel method. Silica acts as a spacer among the nanoparticles to avoid the agglomeration. X-ray diffraction(XRD) reveals the cubic spinel ferrite structure of nanoparticles with crystallite size in the range 37–45 nm. Fourier transform infrared(FTIR) spectroscopy confirmed the formation of spinel ferrite and SiO2. Scanning electron microscopy(SEM) images show that the nanoparticles are nearly spherical and non-agglomerated due to presence of non-magnetic SiO2 surface coating. All these measurements signify that the structural and magnetic properties of Co1 xZnxFe2O4 ferrite nanoparticles strongly depend on Zn concentration and nanoparticle average crystallite size in different Zn concentration regimes.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Composition design of superhigh strength maraging stainless steels using a cluster model

The composition characteristics of maraging stainless steels were studied in the present work investigation using a cluster-plus-glue-atom model. The least solubility limit of high-temperature austenite to form martensite in basic Fe–Ni–Cr corresponds to the cluster formula [NiFe12]Cr3,where NiFe12is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in FCC structure and Cr serves as glue atoms. A cluster formula [NiFe12](Cr2Ni) with surplus Ni was then determined to ensure the second phase(Ni3M) precipitation,based on which new multicomponent alloys [(Ni,Cu)16Fe192](Cr32(Ni,Mo,Ti,Nb,Al,V)16) were designed. These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1273 K for 1 h followed by water-quenching,and finally aged at 783 K for 3 h. The experimental results showed that the multi-element alloying results in Ni3M precipitation on the martensite,which enhances the strengths of alloys sharply after ageing treatment. Among them,the aged [(Cu4Ni12)Fe192](Cr32(Ni8.5Mo2Ti2Nb0.5Al1V1)) alloy(Fe74.91Ni8.82Cr11.62Mo1.34Ti0.67Nb0.32Al0.19V0.36Cu1.78wt%) has higher tensile strengths with YS?1456 MPa and UTS?1494 MPa. It also exhibits good corrosion-resistance in 3.5 wt% NaCl solution.     

Phase analysis of AlFe2B2 by synchrotron X-ray diffraction, magnetic and Mössbauer studies

The structural and magnetic properties of essentially phase pure AlFe_2B_2 prepared by arc melting were compared with a sample containing impurities. Analysis was carried out by means of synchrotron X-ray diffraction, magnetic measurements and M?ssbauer spectroscopy. The analysis of synchrotron X-ray diffraction data confirmed the orthorhombic structure of space group Cmmm for AlFe_2B_2 with Al_(13)Fe_4 as main impurity phase. The magnetic measurements revealed an unsaturated ferromagnetic state in AlFe_2B_2 with a transition temperature(T_c) of 286 K. Isothermal magnetization measurment at 5 K gave a saturation magnetization of 0.7 μB per Fe atom while Arrott plots establish the second order nature of ferromagnetic transition. The thermal evolution of M?ssbauer spectra confirmed the ferromagnetic nature of this material revealing an hyperfine field of 73 kOe and an isomer shift of 0.46 mm/s at 100 K. The M?ssbauer spectra of a phase pure sample was compared with the one containing impurity phases. It is suggested that the low temperature paramagnetic contribution in M?ssbauer spectra of phase pure material may have its origin in some intrinsic phenomena arising from defects or inhomogeneities in crystal structure.     

Core loss analysis of Finemet type nanocrystalline alloy ribbon with different thickness

Nanocrystalline soft magnetic materials are widely used in power electronic applications due to their high permeability,magnetization and low core loss.In this paper,Fe_(73.5)Cu_1Nb_3Si_(15.5)B_7(at%)nanocrystalline alloy ribbons,with ultra-thin thickness of 14μm,and also 18 and 22μm,were prepared by a planar flow casting method with a single roller device.Soft magnetic properties of these ribbons were analyzed after nanocrystallization annealing.The experiments were conducted on toroidal samples using IWATSU B-H Analyzer over a frequency range of 10–100 kHz,at induction amplitudes of 100–500 m T,at room temperature.It was found that the excess eddy current loss P_(ex)was the dominant factor in the overall core loss above 10 k Hz.The toroidal samples made of the 14μm thickness ribbon exhibit very low total core loss of 48 W/kg at a frequency of100 kHz and magnetic flux density of 300 mT.The ratio of the P_(ex)was up to 89%at 100 kHz.The ribbon with lower thickness exhibits lower P_(ex)and therefore lower total core loss.The domain structure evidences were found.It indicates that the ribbons with small thickness are preferable for application in high frequency condition.     

Joining of Si3N4 ceramic using PdCo(Ni SiB)–V system brazingfi ller alloy and interfacial reactions

The wettability of V-active PdCo-based alloys on Si3N4ceramic was studied with the sessile drop method. And the alloy of Pd50.0–Co33.7–Ni4.0–Si2.0–B0.7–V9.6(wt%),was developed for Si3N4ceramic joining in the present investigation. The rapidly-solidified brazing foils were fabricated by the alloy Pd50.0–Co33.7–Ni4.0–Si2.0–B0.7–V9.6. The average room-temperature three-point bend strength of the Si3N4/Si3N4joints brazed at 1453 K for 10 min was 205.6 MPa,and the newly developed braze gives joint strengths of 210.9 MPa,206.6 MPa and 80.2 MPa at high temperatures of 973 K,1073 K and 1173 K respectively. The interfacial reaction products in the Si3N4/Si3N4joint brazed at 1453 K for10 min were identified to be VN and Pd2Si by XRD analysis. Based on the XEDS analysis result,the residual brazing alloy existing at the central part of the joint was verified as Co-rich phases,in which the concentration of element Pd was high up to 18.0–19.1 at%. The mechanism of the interfacial reactions was discussed. Pd should be a good choice as useful alloying element in newer high-temperature braze candidates for the joining of Si-based ceramics.     

Effects of Sn addition on microstructure and mechanical properties of Mg- Zn-Al alloys

The effects of Sn addition(0, 0.5, 1.0, 2.0 and 3 wt%) on microstructure of Mg-4Zn-1.5Al alloy in cast and extruded states were investigated, and the mechanical properties of as-extruded Mg-4Zn-1.5Al-xSn studied. The experimental results showed that the as-cast Mg-4Zn-1.5Al alloy was composed of two phases α-Mg and Mg_(32)(Al, Zn)_(49), while Sn-containing alloys consisted of α-Mg, Mg_(32)(Al, Zn)_(49) and Mg_2Sn phases, and Mg_(32)(Al, Zn)_(49) was not detected after extruding due to that the most of them dissolved into the matrix during the homogenized treatment. The addition of Sn refined the grains of as-cast and as-extruded Mg-Zn-Al alloys obviously. It was noted that the basal texture intensity reduced with increasing Sn content significantly in as-extruded Mg-Zn-Al alloys. The tensile tests results indicated that Sn addition improve the tensile strength of the extruded alloys,while it had a harmful effect on the ductility. When the addition of Sn was 2 wt%, the ultimate tensile strength(UTS), yield strength(YS) and elongation(ε_f) of the alloy were 280 MPa, 147 MPa and 17.4%, respectively.     

Electrochemical properties of LaFeO3-rGO composite

LaFeO_3-xwt% r GO composite(x = 8, 10, 12) was synthesized by ultraphonic stirring and lyophilization method.SEM, TEM and XRD results show that the perovskite-type LaFeO_3 was dispersed by rGO to form special porous structure due to the gauze-shaped wrinkles and folds structure of rGO. It was found that the special porous structure can effectively increase the specific surface area and suppress particle aggregation of LaFeO_3, thus improving the electrical conductivity and appreciably enhancing the electrochemical properties of LaFeO_3. As compared with LaFeO_3, the maximum discharge capacity of the composite(x=10) increased from 209.5 mAhg~(–1) to 334.6 mAhg~(–1).The High rate dischargeability at a discharge current density of 1500 mAg~(–1)(HRD1500) and the capacity retention rate after 100 charge/discharge cycles(S100) of the composite increased by 9% and 17%, respectively.     

Growth, structural, optical, thermal and dielectric properties of a novel semi-organic nonline ar optical crystal: Dichloro-diglycine zinc II

Dichloro-diglycine zinc II(DCDGZ II),a semi-organic nonlinear optical material has been synthesized and single crystals were grown from the aqueous solution up to dimensions 20×10×3 mm3.The title compound,DCDGZ II(C4H10Cl2N2O4Zn H2O) crystallizes into monoclinic structure with the space group of C2/c.The unit-cell parameters were found to be a=14.4191(7),b=6.9180(2),c=12.9452(6) and Z=4.In the crystal structure,DCDGZ II layer is building up alternatingly with layers of water in which the zinc ions lie on a twofold axis.Theoretical calculations for polarizability,which are useful for device fabrication were made using Clausius–Mosotti equation and Penn analysis and the results were compared.Fourier transform infrared(FTIR) spectroscopic studies were performed for the identification of the different functional groups presented in the compound.The UV–vis–NIR absorption spectrum reveals that the lower UV cut-off wavelength is 240 nm.The optical band gap of the crystal was estimated as 2.2 eV.The surface morphology,thermal behaviour,dielectric properties have been studied using SEM,TG/DTA and LCR HITESTER analyzer.The nonlinear optical property of the crystal was also confirmed using Kurtz powder technique.     

Microstructure and oxidation resistance of SiC–MoSi2 multi-phase coating for SiC coated C/C composites

In order to improve the anti-oxidation of C/C composites, a SiC–MoSi2multi-phase coating for SiC coated carbon/carbon composites(C/C)was prepared by low pressure chemical vapor deposition(LPCVD) using methyltrichlorosilane(MTS) as precursor, combined with slurry painting from MoSi2 powder. The phase composition and morphology were analyzed by scanning electron microscope(SEM) and X-ray diffraction(XRD) methods, and the deposition mechanism was discussed. The isothermal oxidation and thermal shock resistance were investigated in a furnace containing air environment at 1500 1C. The results show that the as-prepared SiC–MoSi2coating consists of MoSi2 particles as a dispersing phase and CVD–SiC as a continuous phase. The weight loss of the coated samples is 1.51% after oxidation at 1500 1C for 90 h, and 4.79% after 30 thermal cycles between 1500 1C and room temperature. The penetrable cracks and cavities in the coating served as the diffusion channel of oxygen, resulted in the oxidation of C/C composites, and led to the weight loss in oxidation.     

Synthesis, structure, and optical properties of manganese phthalocyanine thin films and nanostructures

Manganese phthalocyanine(MnPc) nanostructures with different morphologies were prepared on porous anodic alumina oxide(AAO) at different substrate temperature(T_S=50 ℃,80 ℃,120 ℃,180 ℃,240 ℃) in an organic molecular beam deposition(OMBD) system.The nanostructures morphologies were studied using scanning electron microscopy(SEM) and the results showed that the nanostructures morphologies could be modulated by the control of T_S,as a result,the continuous film was obtained at 50 ℃,whereas the nanorods(NRs),nanoribbons(NBs),nanowires(NWs),nanosheets(NSs) and nanoparticles(NPs) were facilely generated as T_S increased.At the same time,the density and the uniformity of the nanostructures decreased.The results of X-ray diffraction(XRD) indicated that only the(3-phase polymorph formed throughout the growth process irrelevant to the T_S.Additionally,the ultraviolet visible(UV-Vis) absorption spectra demonstrated that the main absorption bands of MnPc nanostructures showed a remarkable band broadening as the T_S was increased.