Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Low-temperature densification sintering and properties of CaAl_2Si_2O_8 ceramics with MeO·2B_2O_3(Me=Ca,Sr,Ba)

Dense CaAl2Si2O8 ceramics were prepared via a two-step sintering process at temperatures below 1000°C. First, pre-sintered Ca Al2Si2O8 powders containing small amounts of other crystal phases were obtained by sintering a mixture of calcium hydroxide and kaolin powders at 950°C for 6 h. Subsequently, the combination of the pre-sintered ceramic powders with Me O·2B2O3(Me = Ca, Sr, Ba) flux agents enabled the low-temperature densification sintering of the CaAl2Si2O8 ceramics at 950°C. The sintering behavior and phase formation of the CaAl2Si2O8 ceramics were investigated in terms of the addition of the three MeO·2B2O3 flux agents. Furthermore, alumina and quartz were introduced into the three flux agents to investigate the sintering behaviors, phase evolvements, microstructures, and physical properties of the resulting CaAl2Si2O8 ceramics. The results showed that, because of their low-melting characteristics, the MeO·2B2O3(Me = Ca, Sr, Ba) flux agents facilitated the formation of the CaAl2Si2O8 ceramics with a dense microstructure via liquid-phase sintering. The addition of alumina and quartz to the flux agents also strongly affected the microstructures, phase formation, and physical properties of the CaAl2Si2O8 ceramics.     

Porous SiC ceramics fabricated by quick freeze casting and solid state sintering

Porous SiC ceramics with uniform microstructure were fabricated by quick freezing in liquid nitrogen and solid state sintering.Poly(vinyl alcohol)(PVA) was added as binder and pore morphology controller in this work.The microstructure and mechanical properties of porous SiC ceramics could be controlled by the composition of the aqueous slurries.Both solid content of the slurries and PVA content impacted on the pore structures and mechanical properties of the porous SiC ceramics.The solid content of slurries and PVA content varied from 60 to 67.5 wt%and 2-6 wt%,respectively.Besides,the grain morphology of ceramics was also tailored by changing the sintering temperature from 2050 to 2150 ℃.Porous SiC ceramics with an average porosity of 42.72%,flexural strength of 59.28 MPa were obtained at 2150 ℃ from 67.5 wt% slurries with 2 wt% PVA.     

Effect of SiO2 addition on the dielectric properties and microstructure of BaTiO3-based ceramics in reducing sintering

The effect of SiO₂ doping on the sintering behavior, microstructure, and dielectric properties of BaTiO₃-based ceramics has been investigated. Silica was added to the BaTiO₃-based powder prepared by the solid state method with 0.075mol%, 0.15mol%, and 0.3mol%, respectively. The SiO₂-doped BaTiO₃-based ceramic with high density and uniform grain size were obtained, which were sintered in reducing atmosphere. A scanning electron microscope, X-ray diffraction, and LCR meter were used to determine the microstructure as well as the dielectric properties. SiO₂ can form a liquid phase belonging to the ternary system of BaO-TiO₂-SiO₂, leading to the formation of BaTiO₃ ceramics with high density at a lower sintering temperature. The SiO₂-doped BaTiO₃-based ceramics can be sintered to a theoretical density higher than 95% at 1220℃ with a soaking time of 2 h. The dielectric constants of the sample with 0.15mol% SiO₂ addition sintered at 1220℃ is about 9000. Doping with a small amount of silica can improve the sintering and dielectric properties of BaTiO₃-based ceramics.     

Low-temperature densification sintering and properties of CaAl2Si2O8 ceramics with MeO·2B2O3 (Me=Ca,Sr, Ba)

Dense CaAl2Si2O8 ceramics were prepared via a two-step sintering process at temperatures below 1000°C. First, pre-sintered CaAl2Si2O8 powders containing small amounts of other crystal phases were obtained by sintering a mixture of calcium hydroxide and kaolin powders at 950°C for 6 h. Subsequently, the combination of the pre-sintered ceramic powders with MeO·2B2O3 (Me=Ca, Sr, Ba) flux agents enabled the low-temperature densification sintering of the CaAl2Si2O8 ceramics at 950°C. The sintering behavior and phase formation of the CaAl2Si2O8 ceramics were investigated in terms of the addition of the three MeO·2B2O3 flux agents. Furthermore, alumina and quartz were introduced into the three flux agents to investigate the sintering behaviors, phase evolvements, microstructures, and physical properties of the resulting CaAl2Si2O8 ceramics. The results showed that, because of their low-melting characteristics, the MeO·2B2O3 (Me=Ca, Sr, Ba) flux agents facilitated the formation of the CaAl2Si2O8 ceramics with a dense microstructure via liquid-phase sintering. The addition of alu-mina and quartz to the flux agents also strongly affected the microstructures, phase formation, and physical properties of the CaAl2Si2O8 ce-ramics.     

Dielectric properties of spark plasma sintered AlN/SiC composite ceramics

In this study, we have investigated how the dielectric loss tangent and permittivity of AlN ceramics are affected by factors such as powder mixing methods, milling time, sintering temperature, and the addition of a second conductive phase. All ceramic samples were prepared by spark plasma sintering (SPS) under a pressure of 30 MPa. AlN composite ceramics sintered with 30wt%–40wt% SiC at 1600℃ for 5 min exhibited the best dielectric loss tangent, which is greater than 0.3. In addition to AlN and β-SiC, the samples also contained 2H-SiC and Fe₅Si₃, as detected by X-ray difraction (XRD). The relative densities of the sintered ceramics were higher than 93%. Experimental results indicate that nano-SiC has a strong capability of absorbing electromagnetic waves. The dielectric constant and dielectric loss of AlN-SiC ceramics with the same content of SiC decreased as the frequency of electromagnetic waves increased from 1 kHz to 1 MHz.     

Evaluation of precipitation hardening in TiC-reinforced Ti<Subscript>2</Subscript>AlNb-based alloys

Ti₂AlNb-based alloys with 0.0wt%, 0.6wt%, and 2.0wt% carbon nanotube (CNT) addition were fabricated from spherical Ti-22Al-25Nb powder by sintering in the B2 single-phase region. Phase identification and microstructural examination were performed to evaluate the effect of carbon addition on the hardness of the alloys. Carbon was either in a soluble state or in carbide form depending on its concentration. The acicular carbides formed around 1050℃ were identified as TiC and facilitated the transformation of α₂+B2 → O. The TiC was located within the acicular O phase. The surrounding O phase was distributed in certain orientations with angles of 65° or 90° O phase particles. The obtained alloy was composed of acicular O, Widmanstatten B2+O, and acicular TiC. As a result of the precipitation of carbides as well as the O phase, the hardness of the alloy with 2.0wt% CNT addition increased to HV 429±9.     

Phase modification and dielectric properties of a cullet-paper ash-kaolin clay-based ceramic

Novel ceramics from waste material made of (x) paper ash-(80-x) cullet-20 kaolin clay (10wt% ≤ x ≤ 30wt%) were successfully synthesized using a conventional solid-state reaction technique. Energy-dispersive X-ray analysis confirmed the presence of Si, Ca, Al, and Fe in the waste material for preparing these ceramics. The influence of the cullet content on the phase structures and the dielectric properties of these ceramics were systematically investigated. The impedance spectra were verified in the range from 1 Hz to 10 MHz at room temperature. The phase of the ceramics was found to primarily consist of wollastonite (CaSiO₃), along with minor phases of γ-dicalcium silicate (Ca₂SiO₄) and quartz (SiO₂). The sample with a cullet content of 55wt% possessed the optimum wollastonite structure and exhibited good dielectric properties. An increase of the cullet content beyond 55wt% resulted in a structural change from wollastonite to dicalcium silicate, a decrease in dielectric constant, and an increase in dielectric loss. All experimental results suggested that these novel ceramics from waste are applicable for electronic devices.>     

Evaluation of precipitation hardening in TiC-reinforced Ti_2AlNb-based alloys

Ti_2AlNb-based alloys with 0.0 wt%, 0.6 wt%, and 2.0 wt% carbon nanotube(CNT) addition were fabricated from spherical Ti–22 Al–25 Nb powder by sintering in the B2 single-phase region. Phase identification and microstructural examination were performed to evaluate the effect of carbon addition on the hardness of the alloys. Carbon was either in a soluble state or in carbide form depending on its concentration. The acicular carbides formed around 1050℃ were identified as TiC and facilitated the transformation of α_2 + B2 → O. The TiC was located within the acicular O phase. The surrounding O phase was distributed in certain orientations with angles of 65° or 90° O phase particles. The obtained alloy was composed of acicular O, Widmanstatten B2 +O, and acicular TiC. As a result of the precipitation of carbides as well as the O phase, the hardness of the alloy with 2.0 wt% CNT addition increased to HV 429 ± 9.     

Effect of boehmite sol on the crystallization behavior and densification of mullite formed from a sol–gel precursor

Hybrid mullite sol was synthesized from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS), doped with boehmite sol with different ratios. Pressureless sintering of the xerogel was carried out at different temperatures in the presence of boehmite doping. The xerogel and sintered powder were characterized by FTIR, TG-DSC, XRD, SEM and bulk density. The addition of boehmite caused the formation of metaphase spinel (6Al2O3·SiO2) crystal before the appearance of mullite phase, which could lead to the formation of amorphous phase and suppress the premature formation of mullite. Both of these effects improve the densification of mullite. A maximum density about 98% of the theoretical density (TD, 3.01 g/cm3 ) of mullite could be obtained for 5 wt% boehmite addition at 1200 1C pressureless sintering.     

A.C. conductivity and relaxation dynamics in zinc–borate glasses

The frequency-dependent dielectric dispersion of ZnO–Na2O–Al2O3–B2O3(in mol%) glass prepared by the melt quenching technique is investigated in the temperatur e ranges from room temperature to 420 K. Dielectric relaxation has been analyzed based on the behavior of electric modulus behavior. An analysis of the real and imaginary parts of dielectric is performed assuming the ideal Debye behavior as confirmed by Cole–Cole plot. The activation energy associated with the dielectric relaxation determined from the electric modulus spectra was found to be 1.863 eV, which is close to that the activation energy for d.c. conductivity (1.871 eV), indicating the similar nature of relaxation and conductivity.     

Microstructure, mechanical and thermo-physical properties of hot-pressed Al2O3-GdAlO3-ZrO2 ceramics with eutectic composition

A low cost chemical co-precipitation method was employed to fabricate nanoscale Al_2O_3-GdAlO_3-ZrO_2 powder with eutectic composition. A careful control of reaction conditions was required during the preparation. The synthesized nanopowders exhibited a particle size of 20-200 nm, and were highly dispersive and uniform. The results showed that calcination temperature had an important influence on the phase constituents of the nanopowders. With increasing the calcination temperature, a phase transformation from θ-Al_2O_3 to α-Al_2O_3 and a thermal decomposition from Gd_3 Al_5O_(12)(GdAG) to GdAlO_3 and α-Al_2O_3 occurred in sequence. A calcination temperature of 1300 ℃ was needed for the crystallization of α-Al_2 O_3. These nanosized powders were consolidated via hot pressing to produce a fully densified ceramic composite with eutectic composition. The Al_2O_3-GdAlO_3-ZrO_2 ceramic hot-pressed at 1500 ℃ exhibited a relative density of 99.4%, a flexural strength of 485 MPa and a fracture toughness of 6.5 MPa m~(1/2). The ceramic had a thermal conductivity of 1.9 W m K~(-1) at 1200 ℃ and a thermal expansion coefficient of 9.49 ×10~(-6) K~(-1) at 1100 ℃.     

Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

Synthesis of dental resins using diatomite and nano-sized SiO2 and TiO2

The mechanical properties of dental composites were improved by porous diatomite and nano-sized silica (OX-50) used as co-fillers.The resin composites,filled with silanized OX-50 and silanized diatomit...     

Microstructure and mechanical properties of Nb–Si alloys fabricated by spark plasma sintering

This paper deals with microstructural evolutions and mechanical properties of Nb-Si binaries containing dual-phase Nb/Nb5Si3 with Nb to Nb5Si3 fraction ratios of 90:10,80:20,70:30 and 50:50,prepared by spark plasma sintering(SPS).Dense Nb/Nb5Si3 samples with a relative density larger than 99.5% were obtained by SPS processing.The SPS samples consist of the Nb and Nb5Si3 phases with less than 3% fraction of NbO oxide.Hv at room temperature,and compressive strength at 1150℃ and 1250 1C of the bulk SPS alloys increase monolithically by enhancing fraction of the stiffening Nb5Si3 phase.For example,0.2% yield strength,σ0.2,increases from 175 MPa to 420 MPa at 1150℃ and from 110 MPa to 280 MPa at 1250℃,when the Nb5Si3 fraction increases from 10% to 50%.It is interesting that the fracture toughness,KQ,of the bulk SPS samples seems not to be sensitive to phase fraction.Heat treatment,however,plays a key role on the KQ as compared with that of the as-sintered state,at the corresponding Nb5Si3 fraction and considerably improves the KQ by about 100% for samples with the Nb5Si3 fractions of 10%-30%,and by about 50% for the sample with 50% Nb5Si3 fraction.     

Hot corrosion behavior of nanostructured Gd2O3 doped YSZ thermal barrier coating in presence of Na2SO4 + V 2O5 molten salts

Nickel-based superalloy DZ125 was first sprayed with a NiCrAlY bond coat and followed with a nanostructured 2 mol% Gd_2O_3-4.5 mol% Y_2 O_3-ZrO_2(2 GdYSZ) topcoat using air plasma spraying(APS). Hot corrosion behavior of the as-sprayed thermal barrier coatings(TBCs) were investigated in the presence of 50 wt%Na_2SO_4 + 50 wt% V_2O_5 as the corrosive molten salt at 900 ℃ for 100 h. The analysis results indicate that Gd doped YVO_4 and m-ZrO_2 crystals were formed as corrosion products due to the reaction of the corrosive salts with stabilizers(Y_2O_3, Gd_2O_3) of zirconia. Cross-section morphology shows that a thin layer called TGO was formed at the bond coat/topcoat interface. After hot corrosion test, the proportion of m-ZrO_2 phase in nanostructured 2GdYSZ coating is lower than that of nano-YSZ coating. The result reveals that nanostructured 2GdYSZ coating exhibits a better hot corrosion resistance than nano-YSZ coating.     

DC-bias and visible light effect on dielectric characteristics of La_(0.5)Cr_(0.5)TiO_(3+δ)

La_(0.5)Cr_(0.5)TiO_(3+δ) ceramic sample was prepared via traditional solid-state reaction route. Frequency and temperature dependence of dielectric permittivity were studied in the range of 10~2~ 10~6 Hz and of 77 ~360 K, respectively. It was observed that extraordinarily high low-frequency dielectric constants appeared at room temperature, and dielectric relaxation peaks shifted to higher temperature with increasing frequency. In the dc-bias studies, it was also found that the dielectric permittivity had obviously dc-bias dependence in low frequency, but independence as the frequency above 14 kHz. Interestingly, the dielectric characteristics of the sample had obvious light dependence at room temperature within the measured frequency range. The results demonstrate that visible light improves the dielectric properties of the ceramic by means of I–V and complex impedance analysis.     

Phase stability and thermal conductivity of ytterbia and yttria co-doped zirconia

Rare earth oxides doping has been extensively investigated as one of the effective methods to lower thermal conductivity of 4.55 mol% Y2O3stabilized ZrO2(YSZ) thermal barrier coatings(TBCs).In the present work,5–6 mol% Yb2O3and Y2O3co-doped ZrO2ceramics were synthesized by solid reaction sintering at 1600 1C.The phase stability of the samples after heat treatment at 1500 1C was investigated.Yb2O3and Y2O3co-doped zirconia,especially when Yb2O3/Y2O3≥1,contained less monoclinic phase than single Yb2O3or Y2O3phase doped zirconia,indicating that co-doped zirconia was more stable at high temperature than YSZ.The thermal conductivity of the 3 mol% Yb2O3+3 mol% Y2O3co-doped ZrO2was 1.8 W m 1K 1at 1000 1C,which was more than 20% lower than that of YSZ.