形变温度对高锰TRIP/TWIP钢拉伸性能和组织的影响

研究合金成分为18Mn-0.15C-3Si-3Al的高锰TRIP/TWIP钢(18Mn钢)在-40～200℃范围内的拉伸变形行为,分析形变温度对其拉伸性能、相组成和显微组织的影响.采用EBSD取向成像分析方法着重研究了(111)取向的奥氏体晶粒在拉伸过程中的相组成变化.结果表明,随着形变温度的升高,18Mn钢的抗拉强度和延伸率大体上呈降低趋势,TRIP效应很快消失,形变孪晶和位错滑移取代马氏体相变成为主要的形变机制,即奥氏体晶粒内形变机制的变化为:α＇-M相变→ε-M相变→形变孪晶→位错滑移.18Mn钢中较硬的铁素体在形变过程中能提高材料的加工硬化率,但同时也会引起低温脆性.     

Fe-28Mn-3Si-3Al TWIP钢变形的微观组织特征

采用扫描电镜、透射电镜和电子背散射衍射技术对TWIP钢拉伸变形后的组织进行了观察和分析. 研究结果表明,热处理后的TWIP钢中存在60%的退火孪晶,变形后孪晶量减少为32%. 在拉伸过程中,具有退火孪晶的晶粒内部首先发生变形,产生的变形孪晶遗传了退火孪晶的取向. 变形过程中孪晶和位错相互作用、孪晶和孪晶相互作用以及孪晶取向改变引发滑移的综合结果使TWIP钢同时获得高塑性和高强度,因此变形过程中孪生变形是TWIP钢的主要变形机制.     

高应变速率下钛-钢复合板界面组织特征及变形机制

在高应变速率下,钛-钢复合板不同材料以不同的变形机制协调变形,结合界面起到至关重要的作用.本文分析研究了高应变速率下钛-钢复合板的界面组织特征和变形机制.结果表明:在钢侧,随着应变速率的提高,小角度(3°~10°)晶界含量增多,织构组分{1-12}〈2-41〉逐渐演变为织构{6-65}〈38-6〉和{111}〈1-10〉.在钛侧,随着应变速率的提高,出现了明显的形变孪晶组织,三种形变孪晶如{11-21}〈1-100〉拉伸孪晶、{11-22}〈11-23〉压缩孪晶和{10-12}〈10-11〉拉伸孪晶产生的难易程度不一样,变形机制由常规的"孪生变形为主"转变为"位错滑移与孪生变形共存"的复合变形模式.在结合界面处,随着应变速率的提高,需要适应由两侧产生的不同变形抗力,才能够实现连续变形而不致使材料发生破坏,其主要的协调机制依靠结合界面及附近晶粒的滑移实现变形.     

薄带连铸取向硅钢的热轧孪生行为

薄带连铸流程下取向硅钢粗大λ晶粒(〈100〉//ND,normal direction)的“遗传”会导致磁性能恶化.为解决这一问题,针对取向硅钢的热轧孪生行为开展研究,结果表明:凝固组织粗大的取向硅钢在650℃热轧时可产生大量112〈111〉形变孪晶,这与具有高层错能的硅钢在较高温度下难以孪生变形的传统认知不同.热轧过程中复杂的应力状态降低了变形孪晶的取向依赖性,由于具有更高的储存能,孪晶界/孪晶界及孪晶界/晶界交叉点成为再结晶形核的优先位置,大大提高了常化过程中的再结晶率,受沿孪晶界应变分布及孪晶间距离的限制,沿孪晶界形核的再结晶晶粒通常呈“饼状”,最终形成以细小且取向漫散的再结晶晶粒为主的常化组织,消除了初始凝固组织中有害的粗大λ晶粒.     

Fe-6.5%Si合金温轧后退火过程中再结晶行为

用电子背散射技术观察了700℃温轧板在退火过程中的组织及织构演变以了解其再结晶行为.结果表明,温轧织构由强的(111)〈112〉、较弱的〈110〉∥RD及Goss组成,再结晶织构与之相似.〈110〉∥RD及(111)〈112〉新晶粒首先形成于与之构成小角度晶界的形变晶粒的晶界附近,而在角隅及组织不均匀区等位置孕育出与周围晶粒构成大角度晶界的晶核,择优取向不明显.退火过程中(111)〈112〉在形变组织中累积,最终转化为(111)〈112〉再结晶晶粒.分析认为,温轧后退火是不均匀组织在低储存能驱动下的再结晶过程.(112)〈110〉及(111)〈112〉形变拉长晶粒多发生连续再结晶从而退火织构与形变态相似.在角隅区形成核心进而发生不连续再结晶,核心取向的统计性及不连续晶核的长大弱化再结晶织构,其中Goss晶粒多以此方式形成于(111)〈112〉晶粒内部.     

异步轧制无取向硅钢的再结晶织构演变

在无取向硅钢冷轧过程中采用同步轧制和速比为1.06,1.125,1.19的异步轧制,以考察异步轧制对冷轧和再结晶织构的影响.研究发现,异步轧制减弱冷轧织构中{001}～{112}〈110〉组分,增强{111}〈112〉并减弱{111}〈110〉组分.{111}〈112〉和{111}～{225}〈110〉形变晶粒内剪切带处分别形成η(〈001〉∥RD)及偏离其15°的η′(Ψ=75°,θ=0～45°,φ=0°)再结晶晶粒,η′因晶核尺寸优势发展成为主要织构组分.异步轧制下形变织构的变化有利于改善再结晶织构特征及性能,其影响随速比增大而增强.     

IF钢生产过程中的织构演变

对IF钢生产过程中热轧、冷轧及退火试样的织构演变进行研究.分别借助EBSD和XRD测定和计算了热轧、退火及冷轧试样的取向分布函数及相关织构组分的体积分数.结果发现,热轧板在变形过程中发生了动态再结晶,晶粒为细小的等轴晶,为后续组织发展提供了基础;热轧后试样中的织构很弱,不会影响冷轧织构组分及含量.冷轧过程是织构形成的主要过程,试样中含有4种主要的织构组分:{001}〈110〉、{111｝〈110〉、{111}〈112〉和{112}〈110〉.退火过程中发生再结晶,4种冷轧织构组分在退火过程中均分别转变为{111｝面织构.     

工业纯铝极薄带异步轧制过程中的织构演变

采用异步轧制工艺制备出工业纯铝极薄带,并利用X射线衍射仪(XRD)和透射电子显微镜(TEM)对其织构演变和微观组织进行分析。结果表明,随着变形程度的增加,工业纯铝的晶粒主要向β取向线聚集,形变织构中铜型织构(C){112}〈111〉和黄铜型织构(B){011}〈211〉逐渐增强,轧至100μm厚时试样中晶体取向密度达到最大值26,轧至30μm厚时其取向密度值下降至16,并逐渐形成旋转立方织构(RC){100}〈011〉;形变储能剧烈增加诱发工业纯铝在室温下发生再结晶过程,使系统能量降低,导致织构强度下降。     

小形变量轧制下电工钢中立方织构的形成

尝试了小形变量轧制对立方织构电工钢织构形成的影响.结果表明,对含碳量较低的Fe-3.2%Si铁硅合金的初次再结晶组织施加小形变量形变和退火后,可以得到具有柱状晶结构的晶粒组织,并且得到比较集中的立方织构.柱状晶组织形成过程中伴随着∑5和∑11晶界的减少和最终消失,这种低∑重位晶界的移动主要是由于(100)取向晶粒与基体晶粒之间存在沿〈100〉或〈110〉转动36.9°或50.5°的取向关系.     

30Mn20Al3无磁钢加工硬化行为和组织变化

研究了30Mn20Al3无磁钢冷轧板经1 000和800℃固溶处理10 min后的拉伸变形加工硬化行为和组织结构变化.结果表明:该钢的加工硬化速率在不同变形阶段随真应变的变化呈现不同的规律,加工硬化指数随真应变增加而增加.OM和TEM观察显示,变形量小时,滑移为主要变形机制;变形量增大,变形机制以形变孪晶与位错及形变孪晶之间的交互作用为主;1 000℃固溶处理的晶粒尺寸较800℃大,变形过程中产生的形变孪晶较多,且随着变形量增加,形变孪晶可持续形成,增大了TWIP效应;晶粒尺寸减小使变形过程中的形变孪晶产生的临界应力增大,抑制形变孪晶的产生,从而减小了TWIP效应.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to