镁钙砂碳酸化反应特性的研究

采用TG-DTG技术对镁钙砂细粉的碳酸化反应特征进行研究，以阐明镁钙砂碳酸化反应特性。结果表明，镁钙砂在碳酸化反应过程中主要是其中CaO发生碳酸化转变成CaCO3；镁钙砂中的MgO因其碳酸化温度较低仅发生轻微碳酸化。且反应产物MgCO3在400℃后即开始分解，所以不会对镁钙砂中CaO的碳酸化反应产生太大影响；镁钙砂中CaO碳酸化反应的最大转化速率出现在700℃附近，而镁钙砂显微结构的差异是造成其碳酸化反应程度远低于氧化钙粉末的主要原因。     

镁钙砂表面碳酸化反应动力学计算中的数据处理

用数值分析法对镁钙砂碳酸化反应热重试验数据进行平滑处理,减小了因镁钙砂的显微结构特性导致的热重试验微商数据离散程度对动力学计算的影响,提高了线性拟合相关系数.用模式配合法确定了镁钙砂碳酸化反应动力学"三因子",结果表明:反应前期(α＜33%)表观活化能Ea为31.9 kJ/mol,指前因子A为0.23 s-1,最可几机理可用随机成核、随后生长模式函数Avrami-Erofeev方程描述,其微分表达式为n＝2的Avrami-Erofeev方程,f(α) =(1-α)[-ln(1-α)]-1/2;反应后期 (α＞33%)表观活化能Ea为101.8 kJ/mol,指前因子A为6.4×102,最可几机理可用三维扩散模式函数D3描述,其微分表达式为Jander方程,f(α) = 3 (1-α)2/3/(2 (1-(1-α)1/3).     

氧化钙碳酸化反应动力学研究

采用单一扫描速率法(2℃/min)对氧化钙粉末在CO2气氛中的碳酸化反应进行了热分析动力学研究。结果表明,氧化钙碳酸化反应的最大转化速率在694℃,与在镁钙砂表面碳酸化改性工艺研究中得到的最佳炉温十分接近;而氧化钙的碳酸化反应可用n=2的Avrami-Erofeev随机成核、随后生长模式(机理)函数描述,相应的表观反应活化能为178kJ·mol-1,频率因子为3.4×108min-1。     

添加ZrO_2对镁钙砂抗水化性能的影响

以w(CaO)为55%的镁钙砂细粉为原料、ZrO_2为添加剂,在1550℃温度下烧结5h制备镁钙试样,研究了添加ZrO_2对镁钙试样物相组成、显微结构、烧结性能和抗水化性能的影响。结果表明,添加ZrO_2能促进镁钙材料的烧结,且随着ZrO_2加入量的增加,试样的体积密度逐渐增大,显气孔率减小,抗水化性能逐渐增强,这是由于ZrO_2的加入增大了Ca~(2+)的空位浓度,有利于Ca~(2+)的扩散,促进了镁钙试样的烧结致密化和试样中CaO晶粒的长大。此外,ZrO_2还可与游离态CaO反应生成不易水化的CaZrO_3,该反应发生在晶界等容易水化的部位,改变了镁钙试样的显微结构,又进一步提高了材料抗水化性能;当ZrO_2添加量超过5%后,试样的各项性能变化趋于平缓。综合考虑,该镁钙试样中ZrO_2的适宜添加量为5%。     

钢渣中游离氧化钙和氧化镁碳酸化反应

在CO2含量为99.9%,压力为0.2 MPa条件下,对钢渣粉进行碳酸化处理,并作为水泥混合材料制成净浆试件,对试件进行压蒸,研究碳酸化反应时间对试件体积安定性的影响．结果表明,随着碳酸化反应时间的延长,钢渣中的硅酸盐、游离CaO、Ca(OH)2和游离MgO等物质与CO2气体进行反应,主要生成CaxMg1-xCO3．掺加未经碳酸化处理钢渣的试件,压蒸后破坏严重;掺加碳酸化反应10 min钢渣的试件膨胀率为1.03%,试件有明显裂纹;掺加碳酸化反应20 min钢渣的试件膨胀率为0.29%,符合国家标准,体积安定性合格．碳酸化处理20 min后,钢渣中游离CaO含量由2.54%降至0.84%,游离MgO含量由3.8%降至2.4%,试块压蒸后未出现Mg(OH)2,镁离子以水化硅酸镁形式存在于无定形物中．     

氧化钙砂的致密性对其碳酸化效果及抗水化性能的影响

在二氧化碳气氛下对氧化钙砂进行碳酸化处理时,无论是低密度还是高密度钙砂,碳酸化速率都由扩散过程控制·对低密度钙砂,碳酸化反应在表面和内部同时发生,每个CaO晶粒都被生成的碳酸钙包围,并在生成的碳酸钙中有显微裂纹产生;但对高密度钙砂,碳酸化反应只在表面发生,并在钙砂表面形成一层与钙砂基体结合良好的致密碳酸钙保护层·水化试验结果表明:碳酸化处理能够有效地改善钙砂的抗水化性能,但由于经碳酸化处理的低密度钙砂因显微裂纹的原因,在水化过程中容易开裂崩坏,因此碳酸化处理只适合于改善没有明显显气孔率的高密度钙砂的抗水化性能·     

高钙镁钙耐火材料对无取向硅钢中Al质量分数的影响

以合成高钙镁钙砂为原料,制成CaO质量分数分别为40%、50%和60%的高钙镁钙材料,研究不同CaO质量分数的高钙镁钙材料对无取向硅钢中[Al]质量分数的作用.利用电镜扫描及能谱分析,通过测量了在1 600 ℃反应30 min后镁钙材料反应层中Al和钢水中[Al],分析了不同CaO质量分数的高钙镁钙材料对无取向硅钢中[Al]变化的影响.结果表明,无取向硅钢中的[Al]首先氧化生成Al2O3,然后,与高钙镁钙材料中CaO反应生成CaO·Al2O3,CaO·2Al2O3,CaO·6Al2O3等铝酸盐化合物,以实现对钢液中[Al]的减少作用;随着高钙镁钙材料中的CaO质量分数的提高,对钢液中[Al]的减少作用增强,但当CaO质量分数达到40%时,各种高钙镁钙材料对无取向硅钢中的[Al]的作用基本达到平衡,此时,钢液中[Al]减少率超过96%.说明质量分数达到40%的CaO高钙镁钙材料可用于无铝无取向硅钢的深脱铝处理.     

高钙镁钙耐火材料对无取向硅钢中Al质量分数的影响

以合成高钙镁钙砂为原料,制成CaO质量分数分别为40%、50%和60%的高钙镁钙材料,研究不同CaO质量分数的高钙镁钙材料对无取向硅钢中[Al]质量分数的作用。利用电镜扫描及能谱分析,通过测量了在1600℃反应30 min后镁钙材料反应层中Al和钢水中[Al],分析了不同CaO质量分数的高钙镁钙材料对无取向硅钢中[Al]变化的影响。结果表明,无取向硅钢中的[Al]首先氧化生成Al2O3,然后,与高钙镁钙材料中CaO反应生成CaO.Al2O3,CaO.2Al2O3,CaO.6Al2O3等铝酸盐化合物,以实现对钢液中[Al]的减少作用;随着高钙镁钙材料中的CaO质量分数的提高,对钢液中[Al]的减少作用增强,但当CaO质量分数达到40%时,各种高钙镁钙材料对无取向硅钢中的[Al]的作用基本达到平衡,此时,钢液中[Al]减少率超过96%。说明质量分数达到40%的CaO高钙镁钙材料可用于无铝无取向硅钢的深脱铝处理。     

合成抗水化性致密氧化钙砂的研究

以轻质碳酸钙为原料,研究了分别添加0~20%(摩尔分数)MgO和ZrO2对氧化钙砂烧结和抗水化性的影响.研究结果表明,轻质CaCO3烧结活性高,经1 400℃烧成即可获得相对密度96%以上的CaO砂,但由于CaO晶粒的异常生长,抑制了致密性的进一步提高.添加MgO和ZrO2,能够有效地抑制CaO晶粒生长,有利于气孔排除,促进CaO砂致密度的提高并改善其微观结构.当添加20%MgO时,发育良好的MgO晶粒占据了大部分CaO晶界三角区,形成结构均一的微观结构.当添加20%ZrO2时,CaO晶粒被生成的CaZrO3保护层包围.添加MgO和ZrO2以后,由于致密度的增加,CaO固溶体的形成(添加MgO...     

金属氧化物对镁粉尘层火蔓延的增强机制

易分解的固体惰化剂会增加镁粉尘层的燃烧强度,为探究不易分解的金属氧化物对镁粉尘层燃烧是否具有抑制效应,选用TiO₂,MgO,CaO进行实验研究.结果表明：TiO₂,MgO,CaO在质量分数小于75%时均大幅增强镁粉尘层火蔓延的燃烧强度,火焰相态由纯镁粉尘层燃烧时的表面非均相燃烧转变为气相燃烧;TiO₂通过与镁粉发生化学反应增强火蔓延行为,在TiO₂和Mg恰好完全反应(TiO₂质量分数为63%)的工况下粉尘层火蔓延速率增加了50余倍;MgO,CaO通过增大镁粉颗粒间距,减缓了镁粉燃烧产物形成致密氧化层,从而增强镁粉尘层火蔓延行为.实际生产过程应高度关注镁粉尘与金属氧化物的接触工况,研究结果能够为镁粉尘防护提供理论基础.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.