基于改进多目标遗传算法的连铸二冷过程优化

采用一种改进的多目标遗传算法对二冷工艺进行优化.改进的多目标遗传算法应用概率法选取选择算子，根据适应度值来动态计算交叉和变异概率，能够得到更好的全局最优解，提高算法精度和整体性能.在基于凝固传热模型的二冷优化过程中，采用变间距差分法离散求解传热方程，对比粒子群算法、多目标遗传算法，改进的多目标遗传算法搜索效率高，得到的价值函数最小.在实际生产中，采用优化后的二冷工艺，使得总用水量减少约10%，提高了铸坯质量，达到了节能降耗的要求.     

Al涂层/AZ91镁合金复合铸造界面的研究

对型芯预喷涂一层Al涂层,将AZ91镁合金液浇注到铸型中实现基体和涂层的结合,对凝固后的结合界面组织和相组成进行分析。结果表明,AZ91镁合金液和Al涂层表面的氧化物发生反应,实现了界面间的润湿,形成冶金结合界面。该界面包含3个扩散层:镁合金基体一侧为(Al₁₂Mg₁₇+δ_Mg)共晶组织;中间层为Al₁₂Mg₁₇金属间化合物;Al涂层一侧为Al₃Mg₂金属间化合物,并弥散分布着一些氧化物。试验结果证明,通过复合铸造的方法可以实现Al涂层和镁合金基体的冶金结合。     

双辊薄带连铸低碳微合金钢的铸态组织

采用双辊薄带连铸技术制备了低碳微合金钢薄带，利用OM，SEM和TEM对铸态凝固组织、室温组织、析出及位错进行观察和分析.结果表明:低碳微合金钢铸带的凝固组织中二次枝晶间距约为12~15μm，相对于传统厚板坯和薄板坯连铸，铸带组织得到了明显细化.铸带的原奥氏体晶粒尺寸比较粗大，约为250~410μm，其组织由魏氏铁素体、珠光体和不规则铁素体组成.铸带组织中存在纳米级TiC析出和短棒状的渗碳体.TiC析出没有被薄带连铸的凝固过程及二次冷却过程明显抑制.铸带组织由于铸轧力及二次冷却速率不均匀导致大量位错的产生.     

铸造工艺仿真设计前处理及过程处理应用技术

以应用ProCAST和MAGMAsoft 2款软件为例，针对铸造工艺仿真设计前处理和过程处理每个环节的主要内容与使用方法进行了较为详细地归纳、分析和总结。提出了处理过程的技术路线，并系统地介绍了每项应用内容的操作平台与使用步骤，从而为高效地应用铸造工艺仿真设计提供理论和技术支持。     

Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

Fabrication of plain carbon steel/high chromium white cast iron bimetal by a liquid-solid composite casting process

High-chromium white cast iron (HCWCI) is one of the most widely used engineering materials in the mining and cement indus-tries. However, in some components, such as the pulverizer plates of ash mills, the poor machinability of HCWCI creates difficulties. The bimetal casting technique is a suitable method for improving the machinability of HCWCI by joining an easily machined layer of plain car-bon steel (PCS) to its hard part. In this study, the possibility of PCS/HCWCI bimetal casting was investigated using sand casting. The inves-tigation was conducted by optical and electron microscopy and non-destructive, impact toughness, and tensile tests. The hardness and chemical composition profiles on both sides of the interface were plotted in this study. The results indicated that a conventional and low-cost casting technique could be a reliable method for producing PCS/HCWCI bimetal. The interfacial microstructure comprised two distinct lay-ers:a very fine, partially spheroidized pearlite layer and a coarse full pearlite layer. Moreover, characterization of the microstructure revealed that the interface was free of defects.     

基于RSM-GA法的薄壁蜡模压蜡过程收缩率建模与优化

基于响应面法(RSM),通过一系列的实验建立了薄壁蜡模壁厚方向的收缩率与压蜡参数之间的数学模型,并对模型的合理性与充分性进行了方差分析,对压蜡过程中工艺参数对尺寸收缩率的影响进行了敏感性分析.为了减小收缩率,基于遗传算法(GA)对工艺参数进行了全局优化.     

基于激光共聚焦显微镜模拟微合金钢连铸过程中第二相的析出行为

通过高温激光共聚焦显微镜模拟了微合金钢在不同冷却工艺下的凝固过程,并原位观察该过程样品表面的变化,探讨样品表面变化与第二相析出的关联性。研究结果表明：随着微合金钢钢液的凝固冷却,样品表面会出现细小浮凸;该浮凸出现的温度及分布位置与第二相的析出理论计算及透射电镜表征结果一致;通过原位观察该浮凸的产生,可间接表征第二相的析出,有利于分析第二相对基体组织演变的影响。     

基于DSC的连铸保护渣固体渣膜结晶比定量化分析

通过对差示扫描量热(DSC)曲线的分析,建立了渣膜结晶比计算模型。利用配制已知结晶比的标样,考察了差热分析法确定渣膜结晶比的准确性,并在实验室对工业用中碳钢和低碳钢板坯保护渣制备的渣膜结晶比进行了测定。结果表明:差热分析测量再结晶热焓的方法可以用于渣膜结晶比的判定,相对误差为0~5.03%;用于连铸中碳钢的保护渣渣膜结晶比为88.6%,而低碳钢保护渣的渣膜结晶比为55.0%,其大小趋势与实际要求一致。     

热固性炸药固化过程中的温度分布与热应力研究

为研究热固性炸药固化过程中的温度场分布及热应力变化规律,采用光纤布拉格(Bragg)光栅测试了其加热固化成型时的温度场分布,同时采用Procast软件对不同固化条件下热应力场变化规律进行了数值模拟。固化实验表明:在48℃固化过程中,药柱内部温度差小于3℃,不会产生过高的热积累;数值模拟结果表明:热固性炸药不同固化温度条件下的药柱应力集中主要在下半部分,当固化温度为48℃,60℃和70℃时,固化过程中的最大热应力分别为2.35 k Pa,5.66 k Pa及6.69k Pa,且固化温度越高,应力集中区域面积越大。