多用户正交多级差分混沌键控通信系统

针对传统差分混沌键控(differential chaos shift keying, DCSK)采用多电平方式传输多进制信息导致误比特率(bit error rate, BER)高的缺点,提出一种多用户正交多级DCSK(multi-user orthogonal multi-level DCSK, MOM-DCSK)通信系统。该系统将传输的多进制信息映射为不同的传输系数,多个传输系数分别乘以对应的Walsh码后调制在信息承载信号上,并且通过不同的延时传输多用户信息。在加性高斯白噪声(additive white Gaussian noise, AWGN)信道和多径Rayleigh衰落信道中推导了系统的理论BER公式并进行了仿真分析。结果显示，该系统在传输多进制信息时拥有较好的误码性能,并且在多用户传输领域中有较好的实际应用价值。     

佛山市基本农田保护区养殖鱼塘水质抽样调查与评价

对佛山市5区的基本农田保护区养殖鱼塘水质抽样调查,并采用环境污染指数对水质状况进行评价。结果表明,养殖鱼塘水温和p H值均能达到鱼类正常生长要求,溶解氧较丰富,但水质普遍过肥。在5区20个调查点中,CODCr、NH4+-N和TP超标率分别为90%、30%、85%。5区养殖鱼塘水质的污染程度由高到低依次为禅城区、南海区、三水区、顺德区、高明区。全市养殖鱼塘的综合质量指数为1.44,水质整体上受到重度污染。TP的污染负荷分担率最高,其次是CODCr和NH4+-N。总体来说,佛山市基本农田保护区养殖鱼塘水体有机物污染十分突出,已出现富营养化。     

天津医科大学图书馆中文专业图书资源利用效率统计分析

以天津医科大学图书馆UNICORN集成管理系统的各项记录为数据源,挖掘整合了2004—2013年中文专业图书有关数据,从综合性、动态性角度,统计分析了图书购置数量、图书借阅数量及购书经费分布等有关数据,旨在为提高图书馆管理水平提供参考依据。     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

金具零部件表面防腐蚀试验研究

随着经济的持续高速增长，各行业用电需求增大。在加快特高压骨干电网建设的同时，提高现有电网的输电能力、输电质量成为重中之重。金具是海上换流站的重要组成部分，海洋环境的特殊性，对金具提出了更高的耐腐蚀性能要求。为了探究海洋环境对金具的腐蚀性，选用ZL101A和ZL102两种典型的铝合金金具，采用5种辅助防腐蚀工艺获得5种耐腐蚀样本，并模拟海上工况对其分别进行盐雾腐蚀试验，得出最优防腐蚀工艺。研究表明：ZL101A和ZL102两种铝合金具有一定的耐腐蚀性能，ZL101A铝合金的耐腐蚀性能强于ZL102铝合金的；抛丸处理的防腐措施在ZL101A铝合金样本中的防腐蚀表现要强于ZL102铝合金样本的；阳极氧化在两种材质中防腐蚀表现均为优异，是最优异的防腐蚀工艺。     

丙酸盐对厌氧氨氧化除氮性能及群落结构的影响

为了探究有机碳对厌氧氨氧化的长期影响, 向厌氧氨氧化膜生物反应器中添加不同浓度的丙酸钠, 研究对反应器的除氮效能以及微生物的种群结构和功能变化。结果表明: 反应器主要的脱氮过程由CandidatusBrocadia完成, 当丙酸钠浓度为100 mg/L时, 反应器中由于异养细菌的生长, 可实现碳氮的同步去除, 平均总氮去除率可达91.9%。当丙酸钠浓度为200 mg/L 时, 对Candidatus Brocadia的抑制作用导致反应器除氮性能下降, Candidatus Brocadia的丰度降至41.2%, 总氮去除率降至 78.8%。在有机碳抑制作用解除后, 反应器的除氮性能恢复为86.8%, Candidatus Brocadia丰度增加到54.0%, 但群落多样性下降, 属水平的微生物组成有较大的改变。     

考虑单元互测的测试性指标分配方法

测试性分配是将系统级测试性指标按照一定规则分配给各组成单元的过程。针对现有主流测试性分配方法未考虑单元之间的互测情形,导致分配结果不合理,尤其是部分单元分配指标虚高,难以实现或代价过高等问题,提出了在综合考虑单元故障率、故障危害度等多重影响因素基础上,进一步考虑单元互测因素的测试性指标分配方法。首先实施考虑多重影响因素的指标初次分配;然后基于单元测试性初步设计结果,实施测试性建模与分析,得到单元自检故障率与他检故障率;再利用这两个数据以及初次分配结果构造分配函数实施再次分配,进而得到最终的分配结果;最后应用该方法进行仿真和实例运算,证明了该方法的有效性和先进性。     

户用光伏交流冰箱系统的性能研究

针对昆明地区户用光伏交流冰箱系统的工作特性进行了实验研究,在不同天气条件下对所构建的系统性能进行了测试,测试结果表明,该系统冰箱的冷冻室最低温度可达-22℃,冷藏室温度为0~7℃,在晴天和多云天气情况下,系统带3kg水时制冷系数COP分别为0.08、0.05,系统带8kg负载时制冷系数COP分别为0.28、0.23;在阴雨天气情况下,蓄电池单独向系统供电可保证系统连续工作3d.该光伏冰箱系统在昆明地区运行稳定,并为户用光伏交流冰箱系统性能的进一步优化提供了依据.     

智能高速罐身电阻焊机数字化控制系统

提出了以国产MCT80 0 0F8运动控制器为核心的智能高速罐身电阻焊机数字化控制系统 ,并介绍了系统的组成、工作原理、硬件接口、电机控制方法以及伺服电机的运动关系数学模型 .新的系统有利于提高罐身电阻焊机的制罐生产速度 ,并具有功能全面、可靠性高、控制精确、开放性好以及成本较低等优点