Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Microstructure,mechanical properties and wear resistance of an Al–Mg–Si alloy produced by equal channel angular pressing

Microstructure, mechanical properties and wear resistance in an ultrafine-grained Al–Mg–Si alloy fabricated utilizing a combination of equal channel angular pressing (ECAP) and dynamic aging were investigated in this paper. The results indicated that the grain size of the ECAP alloy was significantly refined, i.e., to ~239 nm after three ECAP passes. Meanwhile, the yield and tensile strength of the ECAPed material reached 340 MPa and 445 MPa, respectively, while maintaining a significant uniform elongation of 14%. Wear resistance results demonstrated that the wear rate, wear depth and width of the ECAPed material decreased in comparison with the solution-treated (SST) and peak-aged (T6) conditions under a load range of 5–25 N. The adhesive wear that occurs in the undeformed specimens at 10 N does not appear in the ECAPed specimen at the same load, indicating that the ECAPed specimen delay the appearance of more serious wear mechanisms under certain loads. The cooperative interaction of high density nano-scale β" precipitates and dislocations resulted in a combination of super-high strength and good work hardening ability which suppressed the extension of cracks between the friction layer and the plastic deformation zone. As a consequence, the combination of ECAP and dynamic aging brings a significant improvement for antifriction performance of the 6061 aluminum alloy.     

基于APAS的篮球技术链攻防时空特征研究

运用三维影像解析系统软件对持球顺步突破后跨步急停跳投这一技术链的攻守影像进行解析.研究结果表明,篮球技术链中每一项技术的运用都有其时间和空间适用性,如果运用得当,链内技术可以产生互为运用手段、互相创造时空条件的效果;经测试,高水平篮球运动员脚的简单反应时和动作反应时高度相关,但在持球队员运用该技术链向左侧突破时,技术链前端技术不能为末端的投篮技术创造时空优势.     

重油催化装置反应系统的技术改造

为了减少炼油厂高低并列式两段再生重油催化裂化装置频繁停工 ,降低干气产率 ,提高加工能力和掺渣能力 ,兰州石化公司炼油厂对该装置进行了技术改造 ,同时多产了液态烃和柴油 .新鲜原料和回炼油改由 BWJ型高效雾化进料喷嘴注入 ,沉降器由原来的三叶快分换为全封闭直联快速分离系统 ,在原来采用急冷油作终止剂的基础上 ,新增急冷水 .通过改造 ,有效地降低了干气产率 ,减少了结焦 ,增加了轻质油收率 ,提高了装置的加工能力、掺渣能力及柴汽比 ,较好地实现了预期目标     

利用Wittig反应合成荧光增白剂DX.EB

基于Wittig反应原理,利用(邻氰基苄基)膦酸二甲酯、(对氰基苄基)膦酸二甲酯、对苯二甲醛和甲醇钠合成了荧光增白剂DX.EB,研究了合成工艺.当原料(邻氰基苄基)膦酸二甲酯∶(对氰基苄基)膦酸二甲酯=1∶1.5,40℃滴加甲醇钠时,收率为最佳,可达74.72%.     

45钢固体粉末法稀土、硼、铬、铝共渗工艺研究

研究了RE_Mg合金对固体粉末法硼、铬、铝共渗层成分、组织和性能的影响 .发现随着RE_Mg合金加入量的增加 ,渗层中Al2 O3的量不断增多 ,当RE_Mg合金加入量为 5 %时 ,渗层中出现连续致密分布的Al2 O3黑区组织 ,对此进行了性能测试和机理探讨     

动态规划确定化学反应器序列最小占用时间的方法

通过用动态规划给出化学反应器序列最小占用时间的设计方法,提出了一个过程的最优化输出设计,该设计在输出产品浓度给定的条件下建立问题的基本设计量和数学模型,利用动态规划原则确定各阶段的占用时间,使总的占用时间为最小值,能够合理的确定各阶段反应器的体积以取得较好的经济效应.图3,表1,参8.     

稻砂土吸附铜镍铅砷能力的比较

通过对砂壤水稻土中Cu,Ni,Pb,As4种元素的单元及复合吸附试验,表明其吸附热力学符合Freundlich方程,吸附能力为Pb Cu>As>Ni.共存元素对土壤吸附某一元素的能力影响不大;用Langmuir方程粗略地估算出这4种元素在土壤中的化学容量.     

温度对臭氧压力的影响

利用公式计算了不同温度下臭氧层内臭氧的最高压力．当臭氧层的温度分别为227K、237K、298K时，臭氧的压力依次为0．0104,0．0103、0．0100Pa．计算表明，温度上升对臭氧的压力的影响是非常小的．     

偏硼酸钠与镁和氢反应的硼氢化钠生成

高的氢压和反应温度有利于片硼酸钠与镁和氢反应生成硼氢化钠，但温度接近镁的熔点时不利于硼氢化钠的生成。在反应物中添加铁、镍和钴将加速硼氢化钠的生成，而铜的加入却阻碍硼氢化钠的生成。