Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

无溶媒结晶技术在维生素B12生产中的应用

为了筛选无溶媒结晶工艺的最佳工艺参数，采用无溶媒结晶法制备维生素B12，以产品含量及收率为考察指标，用响应面分析法优化其制备工艺。得到最佳工艺参数：蒸发温度为65 ℃、真空度为0.09 kPa、结晶前溶液效价为90 000 μg/mL。实验结果表明，无溶媒结晶工艺稳定性较高、操作简单易行，制出的成品含量高、有关物质等质量指标较好，质量及收率整体水平不低于且部分批次优于溶媒结晶工艺。该技术在提高生产安全性的同时，大幅减少了对环境的污染，同时减少了相关工序，有效地降低了生产成本，适用于产业化生产。     

光子探测器在芬兰HIP和克罗地亚RBI的研发制作

该文描述了碲化镉（CdTe）探测器，硅漂移探测器和外加一层转换闪烁体硅探测器（SiS）的设计与制作方法这些硅及CdTe芯片制作工艺及其连接方法是在芬兰的Micronova中心完成的与硅工艺不同的是，CdTe工艺必须在低于150 ℃的温度下完成我们因此专门为CdTe探测器开发了一种低温原子层淀积的氧化铝（Al2O3）薄膜工艺，大小为(10×10×1) mm3的CdTe晶圆由一种无接触的光刻工艺完成.探测器性能是由电流 电压（I V），电容 电压（C V）、瞬间电流方法和精确微质子数方法来检测的实验结果与具有材料和缺陷参数的TCAD模拟结果相符     

Growth, structural, optical, thermal and dielectric properties of a novel semi-organic nonline ar optical crystal: Dichloro-diglycine zinc II

Dichloro-diglycine zinc II(DCDGZ II),a semi-organic nonlinear optical material has been synthesized and single crystals were grown from the aqueous solution up to dimensions 20×10×3 mm3.The title compound,DCDGZ II(C4H10Cl2N2O4Zn H2O) crystallizes into monoclinic structure with the space group of C2/c.The unit-cell parameters were found to be a=14.4191(7),b=6.9180(2),c=12.9452(6) and Z=4.In the crystal structure,DCDGZ II layer is building up alternatingly with layers of water in which the zinc ions lie on a twofold axis.Theoretical calculations for polarizability,which are useful for device fabrication were made using Clausius–Mosotti equation and Penn analysis and the results were compared.Fourier transform infrared(FTIR) spectroscopic studies were performed for the identification of the different functional groups presented in the compound.The UV–vis–NIR absorption spectrum reveals that the lower UV cut-off wavelength is 240 nm.The optical band gap of the crystal was estimated as 2.2 eV.The surface morphology,thermal behaviour,dielectric properties have been studied using SEM,TG/DTA and LCR HITESTER analyzer.The nonlinear optical property of the crystal was also confirmed using Kurtz powder technique.     

Erratum to: Hesperomyces virescens (Fungi,Ascomycota, Laboulbeniales) attacking Harmonia axyridis (Coleoptera,Coccinellidae) in its native range

正Published online:14 March 2014óScience China Press and Springer-Verlag Berlin Heidelberg 2014Erratum to:Chin.Sci.Bull.(2014)59(5–6):528–532DOI 10.1007/s11434-013-0060-1In the original publication of this paper,the first name and the last name of the first author has been documented     

Effect of retained austenite and nonmetallic inclusions on the thermal/electrical properties and resistance spot welding nuggets of Si-containing TRIP steels

Five advanced high-strength transformation-induced plasticity(TRIP) steels with different chemical compositions were studied to correlate the retained austenite and nonmetallic inclusion content with their physical properties and the characteristics of the resistance spot welding nuggets. Electrical and thermal properties and equilibrium phases of TRIP steels were predicted using the JMatPro? software. Retained austenite and nonmetallic inclusions were quantified by X-ray diffraction and saturation magnetization techniques. The nonmetallic inclusions were characterized by scanning electron microscopy. The results show that the contents of Si, C, Al, and Mn in TRIP steels increase both the retained austenite and the nonmetallic inclusion contents. We found that nonmetallic inclusions affect the thermal and electrical properties of the TRIP steels and that the differences between these properties tend to result in different cooling rates during the welding process. The results are discussed in terms of the electrical and thermal properties determined from the chemical composition and their impact on the resistance spot welding nuggets.     

Effect of equal channel angular pressing on aging treatment of Al-7075 alloy

The effect of aging treatment on microstructure and mechanical properties of equal channel angular pressed Al-7075 alloy was examined.Commercial Al-7075 alloy in the solid solution heat-treated condition was processed by equal channel angular pressing through route BCat both the room temperature and 120 1C. Only three passes of equal channel angular pressing was possible due to the low ductility of the alloy at both temperatures. Followed by equal channel angular pressing, the specimens have been aged at 120 1C for different aging times. Mechanical properties were measured by Vickers microhardness and tensile tests and microstructural observations were undertaken using transmission electron microscopy, X-ray diffractometer as well as optical microscopy. Microstructural investigations showed that ultrafine-grained materials with grain size in the range of 200–350 nm and 300–500 nm could be obtained after three passes of equal channel angular pressing at room temperature and 120 1C, respectively. Equal channel angular pressing of solid solution heat-treated Al-7075 alloy accelerates precipitation rate and subsequently leads to a significant decrease in aging time to attain maximum mechanical properties. Furthermore, it is possible to achieve maximum mechanical properties during equal channel angular pressing at 120 1C as a result of dynamic aging and formation of small η′ phase.     

Design of optimum solid oxide membrane electrolysis cells for metals production

Oxide to metal conversion is one of the most energy-intensive steps in the value chain for metals production. Solid oxide membrane (SOM) electrolysis process provides a general route for directly reducing various metal oxides to their respective metals, alloys, or intermetallics. Because of its lower energy use and ability to use inert anode resulting in zero carbon emission, SOM electrolysis process emerges as a promising technology that can replace the state-of-the-art metals production processes. In this paper, a careful study of the SOM electrolysis process using equivalent DC circuit modeling is performed and correlated to the experimental results. A discussion on relative importance of each resistive element in the circuit and on possible ways of lowering the rate-limiting resistive elements provides a generic guideline for designing optimum SOM electrolysis cells.     

行人下肢有限元模型的建立与验证研究

下肢损伤是行人与车辆碰撞事故中的主要损伤形式之一,建立具有较高生物逼真度的行人下肢有限元模型,可以为下肢保护提供有效的研究手段.在下肢长骨(股骨、胫骨、腓骨)、韧带(ACL,PCL,MCL,LCL)及膝关节得到全面验证的基础上,建立了包含骨骼、韧带、肌肉及皮肤等详细解剖学结构的行人下肢有限元模型,并定义了各组织间的接触.利用行人下肢弯曲的生物力学实验,对下肢有限元模型进行了整体弯曲验证.结果显示,下肢有限元模型的损伤形式、损伤发生时刻、膝关节弯矩和弯曲角度均与实验结果吻合较好,能够较真实地反映行人下肢的损伤和生物力学响应,具有较好的生物逼真度.     

Exome sequencing of liver fluke-associated cholangiocarcinoma

Opisthorchis viverrini-related cholangiocarcinoma (CCA), a fatal bile duct cancer, is a major public health concern in areas endemic for this parasite. We report here whole-exome sequencing of eight O. viverrini-related tumors and matched normal tissue. We identified and validated 206 somatic mutations in 187 genes using Sanger sequencing and selected 15 genes for mutation prevalence screening in an additional 46 individuals with CCA (cases). In addition to the known cancer-related genes TP53 (mutated in 44.4% of cases), KRAS (16.7%) and SMAD4 (16.7%), we identified somatic mutations in 10 newly implicated genes in 14.8-3.7% of cases. These included inactivating mutations in MLL3 (in 14.8% of cases), ROBO2 (9.3%), RNF43 (9.3%) and PEG3 (5.6%), and activating mutations in the GNAS oncogene (9.3%). These genes have functions that can be broadly grouped into three biological classes: (i) deactivation of histone modifiers, (ii) activation of G protein signaling and (iii) loss of genome stability. This study provides insight into the mutational landscape contributing to O. viverrini-related CCA.