锭子弹性管的刚度计算及其对动态性能的影响

首先推导了纺纱锭子中开螺旋槽弹性管的等效抗弯刚度及底部刚度系数的计算公式，分析了弹性管各参数对其刚度及振动性能的影响，并进行了模态测试，实验值与计算值基本一致。     

THE PRACTICE OF ACRYLIC SIROSPUN YARN ON THE SEMI WORSTED SPINNING FRAME

The technique of sirospun process is applied on a modified semi-worsted balloonless spinningframe to investigate the effect of spindle-speed,yarn-twist and strand-spacing on yarn properties.Yarn breaking strength,breaking extension,evenness and imperfection are examined on the basisof CCD experimental design.Yarn hairiness is particularly concerned,being found that all spinningparameters tested have significant effects on hairiness and that the minimum number of hairs oc-curs at the strand-spacing of 14.4 mm.Compared to conventional single spun yarn,experimentshave revealed the greatest advantage of using sirospun process is that all sirospun yarns have muchless hairiness.A new sirospun yarn fault,so called“loop”,has also been examined.The most likely cause forthis yarn fault is the strand-tension unbalance between the two strands when low tension spinningis applied.Further analysis and some initial tests have been carried out in the hope of overcomingthis loop fault which is an important obstacle to the application of balloonless spinning.     

THE INFLUENCE OF SPINNING CONDITION ON STRUCTURE & PROPERTIES OF MASS-DYED SUPERFINE PP AS-SPUN FILAMENTS

The effect of colorant additive on the rheology of PP polymer melt and the influence of spinning conditions on the crystalline and orientation structure of mass-dyed as-spun PP filament are reported. The △E~~~ value for all colored chips is higher than that of blank chip to a varying degree. The crystallinity and orientation degree of dyed PP as-spun filament decrease with increasing melt temperature, decreasing spinning speed and increasing denier per filament (dpf), while the crystallinity of dyed as-spun filament increases with the content of colorant additive as a nucleation agent.     

管道纺包芯纱的研究

本文研究了在管道纺纱机上不添加构件而进行包芯纱的纺制。分析了其包芯纱的成纱机理。观察了实际成纱的横截面,证实了棉纤维能够均匀地、完全地包覆在芯丝的周围。也对不同性质的芯丝所纺包芯纱的结构作了观察,并对不同成纱的性质随速度增加而变化的规律作了研究。     

NiAl金属间化合物熔体旋转法制备工艺参数研究

研究了金属间化合物快速凝固薄带的成型过程和影响薄带质量的工艺参数。提出了熔体在喷嘴处进行层流流动的经验关系式，给出了金属间化合物快速凝固薄带制备的最佳工艺参数。     

二十一世纪纺纱工程展望

二十一世纪,一些相关高新技术的发展和应用,将对传统工程产生巨大的影响和推动。文章在此基础上,对新世纪前半叶纺纱技术、纺纱设备以及纺纱工厂自动化的发展进行了展望。     

喷丝头组合花板的真空熔炼

化纤生产行业的粘胶，经过装在组合花板上的喷丝头在酸浴里形成化学纤维。粘胶为碱性物质，酸浴的化学成份为稀硫酸、磷酸，酸浴温度为57℃左右，组合花板内压力为10kg／cm^2，要求组合花板材料在有足够的强度下，具有高耐腐蚀性能。     

裂纹发电机转子轴系电磁激发主参数共振

建立了双质量裂纹转子扭振参数激励系统的数学模型。此模型以发电机产生的电磁力矩作为驱动源，应用多尺度法，给出了参数激励下的主参数共振解。通过对定常解平均方程的稳定性分析，得到了系统主参数共振解的幅频响应曲线。     

集聚纺集聚区须条等截面部分的力学分析

通过对集聚区内须条的集聚过程分析，建立须条的受力模型，发现须条在集聚过程中会产生附加捻度，并且对影响须条附加捻度的各种因素：异型管开槽长度、负压大小、须条和网格套圈间的摩擦因数以及异型管的曲率半径进行了分析。设计相关实验对集聚区内须条的力学模型进行了验证。结果表明所建立的集聚区内须条的力学模型是正确的。     

二醋酯纤维的结构特性

采用DSC、X-射线衍射和密度梯度管等技术研究了二醋酯纤维的结晶、取向等结构特性，初步探讨了不同纺丝工艺对纤维结构特性的影响，发现：二醋酯纤维存在两种晶型结构，结晶度和取向度都较低；以相同二醋片为原料时，纺丝工艺对纤维的结构特性有影响但不明显，而烟用纺丝工艺和纺织用纺丝工艺之间的差别对纤维结构特性的影响则相对较大。