金具零部件表面防腐蚀试验研究

随着经济的持续高速增长，各行业用电需求增大。在加快特高压骨干电网建设的同时，提高现有电网的输电能力、输电质量成为重中之重。金具是海上换流站的重要组成部分，海洋环境的特殊性，对金具提出了更高的耐腐蚀性能要求。为了探究海洋环境对金具的腐蚀性，选用ZL101A和ZL102两种典型的铝合金金具，采用5种辅助防腐蚀工艺获得5种耐腐蚀样本，并模拟海上工况对其分别进行盐雾腐蚀试验，得出最优防腐蚀工艺。研究表明：ZL101A和ZL102两种铝合金具有一定的耐腐蚀性能，ZL101A铝合金的耐腐蚀性能强于ZL102铝合金的；抛丸处理的防腐措施在ZL101A铝合金样本中的防腐蚀表现要强于ZL102铝合金样本的；阳极氧化在两种材质中防腐蚀表现均为优异，是最优异的防腐蚀工艺。     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

不同周围流速和电压下的绝缘子积污特性

为了研究绝缘子在不同电压下表现的积污特性，利用流体力学的相关知识和电场理论，建立了模拟风沙的多物理场仿真模型.研究结果表明，周围流动速度较小时，绝缘子两端的电压增大，积污质量发会有一定程度的增加，且积污与电场力的变化密切相关，结合静电场分析会更准确；周围流动速度较大时，即使电压增大，积污质量也不会发生太大的变化.     

Superior corrosion resistance-dependent laser energy density in(CoCrFeNi)95Nb5 high entropy alloy coating fabricated by laser cladding

(CoCrFeNi)95Nb5 high entropy alloy(HEA)coatings were successfully fabricated on a substrate of Q235 steel by laser cladding technology.These(CoCrFeNi)95Nb5 HEA coatings possess excellent properties,particularly corrosion resistance,which is clearly superior to that of some typical bulk HEA and common engineering alloys.In order to obtain appropriate laser cladding preparation process parameters,the effects of laser energy density on the microstructure,microhardness,and corrosion resistance of(CoCrFeNi)95Nb5 HEA coating were closely studied.Results showed that as the laser energy density increases,precipitation of the Laves phase in(CoCrFeNi)95Nb5 HEA coating gradually decreases,and diffusion of the Fe element in the substrate intensifies,affecting the integrity of the(CoCrFeNi)95Nb5 HEA.This decreases the microhardness of(CoCrFeNi)95Nb5 HEA coatings.Moreover,the relative content of Cr2O3,Cr(OH)3,and Nb2O5 in the surface passive film of the coating decreases with increasing energy density,causing corrosion resistance to decrease.This study demonstrates the controllability of a high-performance HEA coating using laser cladding technology,which has significance for the laser cladding preparation of other CoCrFeNi-system HEA coatings.     

原位生成NbC增强YCF102熔覆层热力学与耐磨性研究

熔覆层性能难以满足特定的工艺要求，已成为限制激光熔覆发展的关键因素之一.鉴于此，在45号钢基体上制备出原位生成NbC增强YCF102熔覆层，并进行了热力学分析.通过XRD，SEM和EDS对其微观形貌及组成成分进行了分析，对其显微硬度及耐磨性进行了研究.结果表明:激光功率的改变对激光熔覆过程中原位反应的反应程度有显著影响，过大或者过小的激光功率均会对原位反应的发生起到抑制作用;YCF102熔覆层中原位生成的NbC颗粒的主要形态为四边形和花瓣形;当激光功率为525W时，原位生成NbC增强YCF102熔覆层具有较高的显微硬度及良好的耐磨性.     

准噶尔盆地车排子凸起新近系沙湾组重矿物、U-Pb年代学特征及物源分析

综合岩石学特征、砂岩碎屑组分特征、重矿物组合特征和锆石U-Pb年代学特征, 探讨准噶尔盆地车排子凸起新近系沙湾组沙一段的沉积特征和物源演化过程。结果表明, 车排子凸起存在南北双物源体系, 沙一段以粗碎屑沉积为主。在一砂组沉积阶段, 扎依尔山为北部物源区, 发育小规模扇三角洲沉积; 中天山及北天山造山带为南部物源区, 发育辫状河三角洲沉积。在二砂组沉积阶段, 中天山供给减弱, 北天山供给加强, 盆地水体加深, 南部辫状河三角洲前端分布小型滨浅湖滩坝。南部物源变化的主要原因可能是受印度板块和欧亚板块碰撞的远程影响, 天山在新生代中新世中期经历强烈的挤压和抬升过程, 造成北天山隆升, 为车排子凸起提供物源。     

KL油田沙三下亚段混合沉积特征及演化

针对目前莱州湾凹陷南斜坡带KL油田沙河街组三段下亚段陆源碎屑与碳酸盐岩混合沉积形成条件、沉积特征及模式认识程度较低的问题，利用该区壁芯、薄片及扫描电镜等资料，结合构造演化、古气候和古地貌背景，在层序格架约束下研究沉积环境，分析其沉积特征。结果表明，研究区发育混合沉积，形成于宽缓斜坡、亚热带湿润气候，兼具湖平面、物源、水动力条件周期性变化等条件；该混合沉积包括相缘渐变混合与原地混合两种沉积类型，互层式和组分式两种混合模式，以及4种混合样式。两种混合沉积类型沉积机理不同，混合模式及组合样式表现较大差异，因而具有不同的储层微观特征。     

苏里格气田马家沟组膏模孔型储层特征及成因

含“膏模”孔泥粉晶云岩是鄂尔多斯盆地马家沟组上组合地层重要储集岩类型，其形成时间和成因对于该类型储层的认识具有重要意义。研究利用苏里格东区丰富的取芯资料，根据岩芯、薄片等观察手段，结合常规物性测试分析，综合研究含“膏模”孔型储层特征及其成因。结果表明，“膏模”孔主要发育于泥粉晶白云岩中，位于向上变浅序列中部，常可见未充填—半充填型与全充填型两类。储层特征方面，该类储集岩主要发育“膏模”孔充填残余孔、渗流粉砂间微孔和基岩晶间溶蚀微孔3类储集空间，物性测试显示储集性能优越，平均孔隙度可达5.34%，平均渗透率为1.02 mD。纵向沉积序列显示“膏模”孔发育受沉积旋回控制，旋回中部“膏模”孔内存在溶蚀，内为云质渗流粉砂充填，旋回顶部具有暴露特征，且可见下一次海侵泥质灌入岩溶系统内，各类特征均指示“膏模”孔形成与准同生期岩溶相关，即“膏模”孔形成于准同生期，而非传统认识的表生阶段。     

南水北调中线工程水源区抗生素抗性基因多样性研究

为了研究丹江口水库和汉江抗生素抗性基因(Antibiotic Resistance Genes, ARGs)的污染现状与分布规律, 采用高通量测序的方法, 于2014年春季和秋季分别对丹江口水库及汉江沿程的ARGs多样性进行检测。分别在春秋两季样本中检测出21和19类ARGs, 其中9类ARGs是水体ARGs的主要组成部分。杆菌肽类ARGs是水体中最主要的ARGs, 而β-内酰胺类ARGs在春季丹江口水库陶岔采样点中占比最高。秋季水体各采样点的ARGs组成结构差异比春季小, 通过NMDS和ANOSIM分析发现ARGs的组成存在显著的季节差异, 甲氧苄氨嘧啶类、多粘菌素类和多重耐药类ARGs是具有显著季节差异的ARGs种类。由相关性分析发现13类具有互相显著强相关关系的ARGs, 其中相关性最强的ARGs很可能共存于一种微生物中。此外, 四环素类和氨基糖苷类ARGs可能作为预测水源区中与其共存ARGs相对丰度的指示种类。研究结果可为饮用水源区的水质保护和ARGs 污染防治与管理提供科学依据。