基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

铅锡合金沉积物的显微组织

将离子浓度比为5∶5的铅锡电沉积分形生长沉积物制备成金相样品，用金相显微镜观察了它们的显微组织。结果表明，在此情况下，铅锡电沉积生成物由两相组成，即铅锡共晶相和铅基固溶相，两相呈交替层状分布。     

铝电解中的阴极过程

对铝电解中的阴极反应、阴极过电压、阴极表面的双电层结构等阴极过程进行了研究,发现在+005～-005V(相对于铝阴极)电位区有一个还原电流峰和一个氧化电流峰,它们是Al3++3e→Al和Al-3e→Al3+·与阳极相比,阴极过电压较小,在001～3A/cm2的Taffel区,约为01V·在阴极表面的双电层中,第一层为Ca2+,Mg2+,Li+和Al3+离子,没有Na+离子,这说明,阴极过电压是因为Mg2+,Ca2+等离子形成的电化学双电层阻力所引起,同时也说明别略耶夫猜想基本是正确的·     

铝合金加工用刀具的使用研究（三）

当前我国各机械加工生产厂家引进国外进口设备及生产线较多，实现引进设备及生产线上刀具的国产化以降低生产成本，成为当前国内整个机械加工领域亟待解决的问题。     

椭圆偏振法研究四方氧化锆对Zr-Sn-Nb合金氧化膜耐腐蚀性能的影响

将经过不同热处理的Zr-Sn-Nb合金样品放在350℃、16．8mol／LPa、0．01mol／LLiOH溶液的高压釜中进行腐蚀。用椭圆偏振法研究氧化膜中的四方氧化锆，发现经过580℃／冷轧／500℃处理的样品在腐蚀42天和190天后氧化膜中的四方氧化锆比其它样品的多。四方氧化锆是影响合金耐腐蚀性能的一个主要因素，四方氧化锆的形成有利于提高合金的耐腐蚀性能。     

苯在Ru-Zn/Ru（0001）合金表面上的吸附——密度泛函研究

为了理解苯在Ru-Zn合金催化剂上的部分加氢催化机理,采用密度泛函方法对苯在Ru-Zn/Ru（0001）面上的吸附进行理论研究。计算结果表明,当苯的碳原子或者共轭双键直接位于表面Zn原子的atop位时,其吸附热较Ru（0001）面上的类似吸附状态下降约60%.Zn原子与苯环C原子之间的排斥作用导致苯环的成键轨道与表面Ru原子的价层轨道之间的空间对称性下降,从而不利于苯与合金表面的键合。当吸附位离开Zn原子时,邻近Zn原子对于苯的吸附基本没有影响。