金属与糖化酶共催化糊精水解加氢制山梨醇的研究

通过考察糖化酶对糊精水解的影响因素,确定了合适的糖化酶水解条件.通过对金属催化剂筛选,寻找出催化性能较好的Ru-P非晶态合金为加氢催化剂.采用超声辅助化学还原法制备了负载型Ru-P非晶态合金催化剂,与糖化酶相结合,用于糊精水解加氢一步法制备山梨醇,得到较高的山梨醇收率.     

交换耦合双能级量子点的全计数统计

基于粒子数分辨的量子主方程,研究了自旋交换耦合双能级量子点中的电子全计数统计,给出了平均电流、散粒噪声和偏斜度.库仑排斥和交换作用导致了平均电流中的小平台;散粒噪声和铁磁电极的极化率以及量子点与电极的不对称耦合密切相关.极化率和量子点电极不对称耦合越大,超泊松散粒噪声越容易出现.当两个自旋单态通道能级参与输运时散粒噪声会大大降低,而当两个自旋三重态通道能级同时参与输运时散粒噪声则会明显增大.     

Examination of dynamic recrystallization during compression of AZ31 magnesium

This study aimed to investigate dynamic recrystallization(DRX)behavior during compression of magnesium alloy AZ31. Cylinder samples were cut from the extruded rod and hot rolled sheet AZ31 for compression test.The samples were compressed using a Gleeble 1500D at a temperature of 300℃and a strain rate of 0.01 s-1.Grain orientations and misorientation angles across grain boundaries for the tested samples were obtained by using electron backscatter diffraction(EBSD)technique.The results showed that strong basal texture was observed after 50%compression(ε=0.69)on both the extruded and hot rolled samples,which have different initial textures.It was observed that with increased strain,DRX grains gradually rotated to basal orientation,and grain boundaries with misorientation angle of near 30°was formed in the samples.At the strain of 0.69,a high fraction of high-angle(60°)boundaries was present in the extruded sample,whereas almost no high angle boundaries were observed in the hot rolled sheet sample.     

Effects of Si and Ce on the microstructure and hydrogen storage property of Ti_(26.5)Cr_(20)V_(45)Fe_(8.5)Ce_(0.5) alloy

In this paper,the effects of Si and Ce on the microstructure and hydrogen storage property of Ti26.5 Cr20V45Fe8.5Ce0.5 alloy were studied,respectively.First of all,effects of Si on the microstructure and hydrogen storage properties of Ti26.5Cr20(V45Fe8.5)1-xSixCe0.5(x=0,0.5,1.0,1.5 and 2.0 at%)alloys were studied by X-ray diffraction,scanning electron microscopy and P-C isotherm measurements.As the Si addition increases,the hydrogen absorption capacities of alloys decrease but the equilibrium pressure incre...     

准晶：奇特而又平凡的晶体—— 2011年诺贝尔化学奖简介

准晶是具有长程准周期性平移序和非晶体学旋转对称的固态有序相。它的出现导致了晶体学与凝聚态物质结构理论的一次革命，极大推动了相关学科的完善和发展。其发现者Daniel Shechtman因此获得2011年度诺贝尔化学奖。本文简介了准晶的发现、结构特征和发展现状，同时介绍了中国科学家在这一领域的独特贡献。     

循环热处理及形变对TC17钛合金片层组织球化和取向的影响

将循环热处理与形变相结合,利用电子背散射衍射等手段探究该工艺对TC17钛合金片层组织球化和取向的影响.结果表明:TC17钛合金在两相区进行单纯的循环热处理其片层组织球化程度有限,而经过循环热处理+压缩变形后,其魏氏组织消失,片层α相得到明显球化,但是其取向均匀性仍没发生较大变化.此外,变形中两相的再结晶速度及其强韧性导致了两相取向的差异性.α相的再结晶速度快于β相,在变形过程中,α相的各向异性首先降低;另一方面,由于α相比β相硬度高,热变形过程中,α相的变形程度小于β相,应变主要集中在与α相邻近的较软的β相,从而导致α相的取向均匀性高于β相.     

ADC14铝合金变速轮组合肋条早期断裂失效分析

采用化学成分分析、扫描电镜断口观察、金相检验等方法对某公司ADC14铝合金变速轮组合肋条的早期断裂原因进行了分析。结果表明，大量不均匀分布的粗大块状初晶硅、沿晶分布的块状脆性相、针状的脆性铁相以及较多的疏松铸造缺陷，严重割裂基体，使肋条的塑性降低、脆性增大，导致肋条产生早期脆性断裂。在此分析的基础上提出了铸造工艺的改进措施。     

基于主模型CAD/CAE集成的卷绕锭轴结构参数优化

高速卷绕头是化纤长丝纺丝机的重要单元机,国内之前研究相对较少。采用虚拟产品开发技术进行高速卷绕头新产品开发的技术创新,提高卷绕头产品开发效率。与同类研究类似,在高速卷绕头产品的虚拟开发过程中,集成CAD/CAE系统存在若干技术瓶颈。基于CAD/CAE系统集成方法的对比分析,建立了主模型CAD/CAE集成框架,并在该框架下进行了高速卷绕头锭轴结构参数优化设计,其优化设计的动力性能分析结果验证了基于主模型CAD/CAE集成框架进行高速卷绕锭轴部件虚拟开发的有效性。

Abstract：

Researches based on the high speed winder, which is a key unit machine for filaments treatment, are relatively rare in China. The techniques of virtual product development （VPD） were applied to improve the new product development of the high speed winder, which would raise the product development efficiency of the high speed winder. Similarly to the research of this kind, in the procedure of developing the virtual product for the high speed winder, there were several key technical problems in the CAD/CAE integrated system. The contrast analysis of the CAD/CAE integrated methods was given; furthermore, the CAD/CAE integrated framework based on master model was built, in which the structural parameters of the high-speed winder chuck was optimized for design. The dynamic characteristics analysis for the optimization design was done; consequently, the result indicates that in the CAD/CAE integrated framework based on master model, the structural parameter optimization of high-speed winder chuck is available.     

4045铝合金热变形行为及其加工图

采用Gleeble-3500热模拟试验机对4045铝合金在变形速率为0.01~10 s-1，变形温度为300~450 ℃条件下进行等温热压缩实验，研究了该合金的热变形行为及其热加工特性.结果表明：4045铝合金热变形过程的流变行为可用双曲正弦模型来描述，其平均激活能为189.93 kJ/mol.基于动态材料模型(DMM)获得了4045铝合金的热加工图，并结合热加工图和金相显微组织分析得到了该合金在实验参数范围内较优的热加工工艺参数范围：加工温度为380~450℃，变形速率为0.1~0.3 s-1.     

铜合金三酸抛光微观效果研究

通过扫描电子显微镜微观观察的方法对三酸化学抛光液中各组分对铜合金表面抛光效果的影响进行了研究.结果表明,采用微观观察法能够更直观有效地研究各组分对铜合金表面抛光效果的影响,在此基础上,获得铜合金表面最佳抛光液:磷酸200~300ml/L、硫酸200~400ml/L(磷酸+硫酸500~600ml/L)、硝酸200~250ml/L(紫铜)、40~150ml/L(黄铜)、盐酸5~15ml/L.经处理的铜合金表面不仅外观光亮、微观平整,而且铜合金表面制备的转化膜中性盐雾测试时间更长、防腐性能更好.根据扫描电子显微镜观察铜合金微观形貌获得最佳抛光液组成的方法,简单方便、准确有效