第三方物流服务质量约束下具有利他性的网购供应链决策模型*

针对单个网络商店和单个第三方物流(TPL)形成的服务供需关系,在TPL服务质量约束下构建了一个基于利他属性的网购供应链决策模型,讨论了利他属性对网购供应链系统的影响。首先在分散决策模式下,探讨了系统的均衡解和绩效;然后,分析了集中决策模式下参与者的决策和利益情况,对比分析发现分散决策模式下网络商店和TPL会因利益冲突而使系统决策失衡,从而降低了供应链参与者利润和系统绩效;在此基础上,讨论了在TPL服务质量约束下利他性与系统决策和绩效的关系,结论表明:利他属性的存在有助于改善系统决策和供应链绩效;最后,通过数值分析,进一步揭示了单方参与者具有利他性时的系统决策和绩效的变化规律,以及双方参与者切利他性互动情景下系统决策的变化规律。     

广义r-部完全超图的边色数

研究了广义r-部完全超图的边色数的问题.在r-部完全超图与t-一致完全超图的着色基础上,确定一类特殊的广义r-部完全超图的边色数,对一般的广义r-部完全超图的边色数给出了上界,推广了r-部完全超图与t-一致完全超图的着色结论.      

多分量地震监测系统AETA的研究与实现

研制多分量地震监测系统AETA(acoustic & electro-magnetic testing all in one system)。在云南、四川、西藏、河北、北京、广东等地区的现场实验表明, 该系统能够满足大区域密集布设中高灵敏度、低成本和易布设的需求。同时, 若干点的实验观测数据和均值、振铃率、峰值频率在一定程度上反映了映震效果。目前正在中国西南部、首都圈、台湾海峡等地区密集布设, 系统地开展映震效果研究。     

Effect of Ce addition on microstructures and mechanical properties of A380 aluminum alloy prepared by squeeze-casting

The effect of cerium (Ce) addition on the eutectic Si, β-Al₅FeSi phase, and the tensile properties of A380 alloy specimens prepared by squeeze-casting were studied by optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The experimental results showed that Ce more effectively modified the eutectic Si and refined the β-Al₅FeSi. The refinement effect significantly increased under a specific pressure of 100 MPa with the addition of Ce from 0.1wt% to 0.9wt%. In contrast, the average length and the aspect ratio of the eutectic Si and β-Al₅FeSi exhibited their optimal values when the content of the added Ce was greater than 0.5wt%. Needle-like Al8Cu4Ce was precipitated with the addition of excessive Ce; hence, the mechanical properties of A380 gradually decreased with increasing Ce content in the range from 0.3wt% to 0.9wt%.     

高速大功率车用永磁同步电机电磁诱发转子横向振动特性

高速大功率车用永磁同步电机的转子轴系是一个涉及电磁、机械高度耦合的非线性系统,因此转子动力学性能是高速车用永磁同步电机设计必须关注的问题.建立了电机中由于转子偏心引起的电磁激励解析模型,以转子动力学和非线性动力学为基础,建立永磁电动机转子系统的非线性模型,用解析法计算得到转子横向振动的幅频特性,结果表明转子横向振动具有负刚度和失稳幅值跳跃现象.最后通过数值计算对等效解析计算的结果进行了验证.     

Damage evolution and failure mechanism of thermal barrier coatings under Vickers indentation by using acoustic emission technique

Acoustic emission(AE) technique was adopted to monitor the damage evolution of air plasma-sprayed(APS) yttria-partially-stabilized zirconia(YSZ) thermal barrier coatings(TBCs) during instrumented indentation testing, and then the failure mechanisms were investigated by cluster analysis and wavelet transform methods.The results of cluster analysis showed that there were three classes associated with distinct failure types for the 8YSZ coatings under Vickers indentation. Based on wavelet transform, these three clusters could be clearly distinguished from their dominant frequency bands, which were concentrated on levels A5(0–156.25 kHz), D5(156.25–312.5 kHz) and D4(312.5–625 kHz), respectively. Thus, the failure mechanism of 8YSZ coatings under Vickers indentation could be clarified by the distribution of different failure types in indentation depth. To sum up, as indentation load increases, the 8YSZ coatings can accommodate the indenter by elastic or little plastic deformation, microcracks propagation and then debonding at the splat boundaries. By comparing the distribution of AE signals induced by different failure types in indentation depth for samples with different thermal exposure time, it can be inferred that thermal exposure treatment can accelerate the degradation of APS 8YSZ TBCs.     

二氧化硅微球的可控制备研究

通过St9ber法制备二氧化硅微球.研究了水醇比例、无机盐种类含量等对二氧化硅微球的微观形貌和粒径分布影响.结果表明,随着反应溶液中去离子水量的增加,二氧化硅微球的粒径逐渐变小.此外,无机盐的添加也会在一定程度上促进二氧化硅微球的长大.究其原因,是因为电解质的加入会破坏微球表面双电层的稳定性,进而促使其发生团聚形成粒径更大的颗粒.     

超密齿面铣刀的铣削力波动特性及其影响

提出了一种超密齿面铣刀概念,并推导了x和y方向的铣削力计算模型,分析了超密齿刀具铣削力及其波动规律.结果显示:随刀具的转动铣削力呈锯齿状变化,x向铣削力波动呈现两个山峰状,在三齿同时参与切削时波动最小.y向铣削力波动随初始切入角的增大先增大后减小,对比发现超密齿刀具铣削力波动远小于疏齿刀具.提出用单位体积材料所需切向铣削力大小来评价超密齿刀具和疏齿刀具性能.通过超密齿面铣刀的铣削实验验证了铣削力计算模型,并发现铣削力波动是影响工件表面粗糙度的因素之一,同时也反映出超密齿刀具的加工优越性.     

北京市水资源利用与经济增长动态关系研究——基于VAR与SVAR模型分析

基于1990—2012年北京GDP数据和三次产业用水量数据,进行GDP数据与三次产业用水量的平稳性检验和协整检验,检验通过后,对四组数据构建SVAR模型,利用脉冲响应函数,分析北京GDP与三次产业用水量之间的相互关系,结果显示第一产业用水量、第二产业用水量与北京GDP的增长负相关,第三产业用水量与北京GDP的增长正相关.     

Deep cleaning of a metallurgical zinc leaching residue and recovery of valuable metals

Huge quantities of zinc leaching residues (ZLRs) generated from zinc production are dumped continuously around the world and pose a potential environmental threat because of their considerable amounts of entrained heavy metals (mainly lead). Most ZLRs have not been properly treated and the valuable metals in them have not yet been effectively recovered. Herein, the deep cleaning of a ZLR and recovery of valuable metals via a hydrometallurgical route were investigated. The cleaning process consists of two essential stages:acid leaching followed by calcium chloride leaching. The optimum conditions for extracting zinc, copper, and indium by acid leaching were a sulfuric acid concentration of 200 g·L-1, a liquid/solid ratio of 4:1 (mL/g), a leaching time of 2 h, and a temperature of 90℃. For lead and silver extractions, the optimum conditions were a calcium chloride concentration of 400 g·L-1, a pH value of 1.0, a leaching time of 1 h, and a temperature of 30℃. After calcium chloride leaching, silver and lead were extracted out and the lead was finally recovered as electrolytic lead by electrowinning. The anglesite phase, which poses the greatest potential environmental hazard, was removed from the ZLR after deep cleaning, thus reducing the cost of environmental management of ZLRs. The treatment of chlorine and spent electrolyte generated in the process was discussed.