基于扫描数据零件轮廓特征自动识别的方法

主要研究基于扫描数据自动识别零件轮廓特征的方法与技术．首先给出了零件轮廓特征自动识别的工作流程，然后提出了零件轮廓特征自动识别的原理与算法，最后通过具体实例验证了本方法的优点及可行性。     

用正交试验法确定最佳调剖施工参数

针对文明寨油田地质特征和开采现状，按照油藏数值模拟原理，以调剖井对应油井的增油降水创经济效益大小为考核指标，运用正交试验的均衡分散性和整齐可比性及Ｌ９（３４），正交表进行调剖最佳施工参数试验．经现场试验、分析、讨论发现：影响调剖效果的主要因素是措施半径，其次为施工排量和注入方式，且最佳施工参数是措施半径在３．５ｍ左右，施工排量在１９ｍ３／ｈ左右，按连续注入方式调剖。经文明察油田、卫城油田、马寨油田５０井次现场试验证明，较好地改善了注水井吸水剖面，对应油井取得了明显的增油降水效果，收到了较好的经济和社会效益．     

堆焊切粒刀技术初探

介绍堆焊切粒刀的优点 ,着重探讨了采用靠模法加工堆焊切粒刀螺旋槽的原理 ,论证了所介绍加工工艺的合理性 .事实证明 ,采用介绍的加工工艺生产的堆焊切粒刀 ,可满足设计的技术性能 ,质量可达到国外同类产品的水平     

中国现当代寓言创作的缺失

中国现当代寓言创作虽然取得了很大的成就,但相当一部分作品从立意到表现却存在着脱离讽喻性、失去故事性、忽视原创性的倾向。中国现当代寓言的创作应在这些方面有所改进。     

基于三阶累积量奇异值分解的雷达目标识别

基于一维距离像三阶累积量矩阵的奇异值分解 ,由非零奇异值构成奇异值矢量作为正则子空间法的输入 ,提出一种雷达目标一维距离像识别方法 ,对目标进行分类识别。该方法一方面利用三阶累积量提高了抗噪性能 ,同时又使用非零奇异值矢量减少了存储量与运算量。仿真实验结果表明 :在低信噪比 ,该方法的识别率高于特征子空间法     

A non-commutative time-frequency tomography

The characterization of non-stationary signal requires joint time and frequency information. However, time and frequency are a pair of non-commuting variables that cannot constitute a joint probability density in the time-frequency plane. The time-frequency distributions have difficult interpretation problems arising from negative and complex values or spurious components. In this paper, we get time-frequency information from the marginal distributions in rotated directions in the time-frequency plane. The rigorous probability interpretation of the marginal distributions is without any ambiguities. This time-frequency transformation is similar to the computerized axial tomography (CT or CAT) and is applied to signal analysis and signal detection and reveals a lot of advantages especially in the signal detection of the low signal/noise (S/N).     

Study on End Milling Generation Surface Model and Simulation in View of Main Axle s Tolerance

In accordance with the relative movement between end-milling cutter and workpiece surface, a theoretical generation model for milled surface was established with the movement error of principal axle considered. Then the milled surfaces under various cutting condition were simulated, the results of which showed that end milled surfaces were of “vaulted profile“, heights of surface irregularty at various points to be different with maximum value in the middle and smaller at both sides, the difference were ...     

剃齿时齿形中凹现象的形成机理

本文综合啮合原理、微分几何和弹性力学的基础理论,对剃齿过程中刀具齿面和被剃齿轮齿面间的失配进行了分析。最后利用径向力求出了齿面间的压切量,从而解释并验证了剃齿过程中产生的齿形中凹现象。这对提高剃齿精度、降低噪音有着重要意义。     

全站仪线路纵、横断面测量

运用全站仪放样及对边测量功能，在已知控制点上设站，方便、快捷、精确的进行线路的纵、横断面测量。     

修形ZI蜗轮滚刀齿形合格长度的研究

本文研究了修形ZI蜗轮滚刀齿形误差的计算方法,从理论上分析了滚刀设计参数和铲磨工艺参数对齿形误差的影响,提出了变砂轮中心高铲磨新工艺,为增加滚刀齿形合格长度开辟了新途径．